GRE over IPSEC Configuration
IPSec-Over-GRE和GRE-Over-IPSec方式配置上的区别为：
GRE-Over-IPSec IPSec-Over-GRE
ACL定义 GRE数据流 内网数据流
IKE peer中指定的remote-address 对方公网地址 对方GRE tunnel地址
应用端口 公网出口 GRE tunnel上
技术特点:
IPSec (ESP) tunnel only IP unicast traffic
GRE encryption non-ip and ip multicast or broadcast packets into ip unicast packets
Using a GRE tunnel inside an ipsec tunnel uses only three SA (at maximum)
GRE---Generic Routing Encapsulation
GRE是一个三层协议,无连接,没有安全性,支持的协议:IP / IPX / Apple Talk
Tunnel Mode 包结构: | IP | ESP | IP | GRE | IP | TCP | Data | ESP |
|<=== Encrypted Payload ===>|
Transport Mode 包结构: | IP | ESP | GRE | IP | TCP | Data | ESP |
|<=== Encrypted Payload ===>|
实验 1 :
本实验Tunnel Mode的包结构:
..| Peer source Peer destination| ESP| GRE的源地址 GRE的目标地址| GRE | 源IP 目标IP | data | ESP |..
本实验Transport Mode 包结构:
由于"Peer source Peer destination"(加密点)等于"GRE的源地址 GRE的目标地址"(通信点),所以包结构更改为: ...| GRE的源地址 GRE的目标地址| ESP| GRE | 源IP 目标IP | data | ESP |...
老命令:
起Tunnel:
R2(config)#interface tunnel 23
R2(config-if)#ip address 23.1.1.2 255.255.255.0 <===起tunnel地址
R2(config-if)#tunnel source 12.1.1.2
R2(config-if)#tunnel destination 13.1.1.3
--------------------------------------------
R3(config)#interface tunnel 23
R3(config-if)#ip address 23.1.1.3 255.255.255.0
R3(config-if)#tunnel source 13.1.1.3
R3(config-if)#tunnel destination 12.1.1.2
宣告:
R2(config-if)# router eigrp 90 <===不用宣告连接Internet的接口
R2(config-router)#no auto-summary
R2(config-router)#network 100.2.2.0 0.0.0.255 <====宣告内部网络
R2(config-router)#network 23.1.1.0 0.0.0.255 <====宣告tunnel地址
-----------------------------------------------
R3(config-if)#router eigrp 90
R3(config-router)#no auto-summary
R3(config-router)#network 100.3.3.0 0.0.0.255
R3(config-router)#network 23.1.1.0 0.0.0.255
IKE Phase I Policy:
R2(config)#crypto isakmp policy 1
R2(config-isakmp)#authentication pre-share
R2(config-isakmp)#hash md5
R2(config-isakmp)#encryption 3des
R2(config-isakmp)#group 2
R2(config)#crypto isakmp key 0 wolf address 13.1.1.3 <===使用物理口地址
-----------------------------------------------------
R3(config)#crypto isakmp policy 1
R3(config-isakmp)#authentication pre-share
R3(config-isakmp)#hash md5
R3(config-isakmp)#encryption 3des
R3(config-isakmp)#group 2
R3(config)#crypto isakmp key 0 wolf address 12.1.1.2
IPSec Phase II Policy:
R2(config)#crypto ipsec transform-set cisco esp-des esp-sha-hmac
模式:
R2(cfg-crypto-trans)#mode tunnel <===使用"tunnel"模式
或者: R2(cfg-crypto-trans)#mode transport <=== 使用"transport"模式.(只有"Peer source Peer destination"等于"GRE的源地址 GRE的目标地址"的特例中,才能使用,且只能在25系列路由器上做)
R2(config)#ip access-list extended gre
R2(config-ext-nacl)#permit gre any any <===对条件可以抓的更细(any:可换成GRE的SOURCE/DESTINATION)
R2(config)#crypto map huawei 10 ipsec-isakmp
R2(config-crypto-map)#set peer 13.1.1.3 <===使用物理口地址
R2(config-crypto-map)#set transform-set cisco
R2(config-crypto-map)#set pfs
R2(config-crypto-map)#match address gre
-----------------------------------------------
R3(config)#crypto ipsec transform-set cisco esp-des esp-sha-hmac
R3(cfg-crypto-trans)#mode tunnel
R3(config)#ip access-list extended gre
R3(config-ext-nacl)#permit gre any any <===对条件可以抓的更细
R3(config)#crypto map huawei 10 ipsec-isakmp
R3(config-crypto-map)#set peer 12.1.1.2
R3(config-crypto-map)#set transform-set cisco
R3(config-crypto-map)#set pfs
R3(config-crypto-map)#match address gre
Apply VPN Configuration
R2(config)#interface ethernet 0/0
R2(config-if)#crypto map huawei
------------------------------------
R3(config)#interface ethernet 0/0
R3(config-if)#crypto map huawei
新命令: 不需要感兴趣流,不需要MAP,不需要set peer
... <===之前的都一样
IPSec Phase II Policy:
R2(config)#crypto ipsec transform-set cisco esp-des esp-sha-hmac
R2(config)#crypto ipsec profile GREPRO <===只有26系列以上路由器才支持
R2(ipsec-profile)#set transform-set cisco
Apply VPN Configuration
R2(config)#interface tunnel 23
R2(config-if)#tunnel protection ipsec profile GREPRO
R2#show crypto ipsec sa <===可以查看协商成"transport"模式
