CC2640R2F学习笔记（2）——OLED屏使用

一、简介

1.1 硬件规格

SSD1306规格书：
链接：https://pan.baidu.com/s/1BtCtp87fTB7VXBG-20czWQ 提取码：vtqv

OLED尺寸： 0.96寸
OLED像素： 128 * 64
OLED驱动IC： SSD1306
接口类型： 4线SPI、3线SPI、IIC接口，可通过配置模块上的电阻等元件切换

1.2 接口定义

引脚	功能说明
GND	电源地
VCC	电源正 3.3~5V
D0	SPI接口时为SPI时钟线，IIC接口时为IIC时钟线
D1	SPI接口时为SPI数据线，IIC接口时为IIC数据线
RST	OLED复位，OLED在上电后需做一次复位
DC	SPI接口时SPI数据/命令选择脚，IIC接口时用来设置IIC地址

二、OLED控制流程

2.1 硬件连接

OLED引脚	香瓜CC2640R2F开发板引脚
GND	GND
VCC	VCC
D0	IOID_9
D1	IOID_10
D0	IOID_9
RST	IOID_4
DC	IOID_26

2.2 总线协议

IO口软件模拟SPI

2.3 软件控制流程

①IO初始化。

②根据时序初始化LCD。

③显示。

三、移植文件

链接：https://pan.baidu.com/s/1FT7PMZoV8jUgoB6WUEkAEw 提取码：wifz
将 board_oled.c 和 board_oled.h 两个文件拖拽至CCS工程的Application文件夹下

添加文件过程中，选项选择如下

3.1 board_oled.c

/*********************************************************************
 * INCLUDES
 */
/* BIOS Header files */
#include <ti/sysbios/knl/Task.h>
#include <ti/sysbios/knl/Clock.h>
#include <ti/sysbios/knl/Semaphore.h>
#include <ti/sysbios/knl/Queue.h>

/* Board Header files */
#include "Board.h"

#include "util.h"
#include "board_oled.h"

#include <string.h>
#include <stdio.h>

/******************************************************************************
 * DEFINITIONS
 */
#define OLED_SCL			IOID_9		//SCLK  时钟 D0（SCLK）
#define OLED_SDA			IOID_10		//SDA   D1（MOSI） 数据
#define OLED_RST			IOID_4		//_RES  hardware reset   复位 
#define OLED_DC				IOID_26		//A0  H/L 命令数据选通端，H：数据，L:命令
 
#define X_WIDTH				128
#define Y_WIDTH				64

#define HAL_OLED_MAX_CHARS	16
#define HAL_OLED_MAX_BUF	25

#define OLED_SCL_1()		PIN_setOutputValue(OLEDPinHandle, OLED_SCL, 1)
#define OLED_SCL_0()		PIN_setOutputValue(OLEDPinHandle, OLED_SCL, 0)
#define OLED_SDA_1()		PIN_setOutputValue(OLEDPinHandle, OLED_SDA, 1)
#define OLED_SDA_0()		PIN_setOutputValue(OLEDPinHandle, OLED_SDA, 0)
#define OLED_RST_1()		PIN_setOutputValue(OLEDPinHandle, OLED_RST, 1)
#define OLED_RST_0()		PIN_setOutputValue(OLEDPinHandle, OLED_RST, 0)
#define OLED_DC_1()			PIN_setOutputValue(OLEDPinHandle, OLED_DC, 1)
#define OLED_DC_0()			PIN_setOutputValue(OLEDPinHandle, OLED_DC, 0)

#define LCD_SUPPORT			0

/*********************************************************************
 * LOCAL VARIABLES
 */
/* Application OLED pin configuration table */
static PIN_Config OLEDPinTable[] = {
	OLED_SCL | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
	OLED_SDA | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
	OLED_RST | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
	OLED_DC  | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
	PIN_TERMINATE		// Terminate list
};

/* Pin driver handle */
static PIN_Handle OLEDPinHandle = NULL;
static PIN_State OLEDPinState;

/*********************************************************************
 * LOCAL FUNCTIONS
 */
#if LCD_SUPPORT
//16*16的点阵字体取模方式：共阴——列行式——逆向输出
static const unsigned char F16x16[] =
{
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	
	/*--  文字:  深  --*/
	/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
	0x10,0x61,0x06,0xE0,0x00,0x26,0x22,0x1A,0x02,0xC2,0x0A,0x12,0x32,0x06,0x02,0x00,
	0x04,0xFC,0x03,0x20,0x20,0x11,0x11,0x09,0x05,0xFF,0x05,0x09,0x19,0x31,0x10,0x00,

	/*--  文字:  圳  --*/
	/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
	0x10,0x10,0x10,0xFE,0x10,0x10,0xFE,0x00,0x00,0xFC,0x00,0x00,0x00,0xFE,0x00,0x00,
	0x08,0x08,0x04,0x47,0x24,0x18,0x07,0x00,0x00,0x1F,0x00,0x00,0x00,0x7F,0x00,0x00,

	/*--  文字:  市  --*/
	/*--  宋体12;  此字体下对应的点阵为：宽x高=16x16   --*/
	0x04,0x04,0x04,0xE4,0x24,0x24,0x25,0xFE,0x24,0x24,0x24,0x24,0xE4,0x04,0x04,0x00,
	0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0xFF,0x00,0x00,0x10,0x20,0x1F,0x00,0x00,0x00,
};

//8*16的点阵
static const unsigned char F8X16[]=	
{
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 0
	0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 1
	0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 2
	0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 3
	0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 4
	0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 5
	0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 6
	0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 7
	0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 8
	0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 9
	0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 10
	0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 11
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 12
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 13
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 14
	0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 15
	0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 16
	0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 17
	0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 18
	0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 19
	0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 20
	0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 21
	0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 22
	0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 23
	0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 24
	0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 25
	0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 26
	0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 27
	0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 28
	0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 29
	0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 30
	0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 31
	0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 32
	0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 33
	0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 34
	0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 35
	0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 36
	0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 37
	0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 38
	0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 39
	0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 40
	0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 41
	0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 42
	0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 43
	0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 44
	0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 45
	0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 46
	0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 47
	0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 48
	0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 49
	0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 50
	0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 51
	0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 52
	0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 53
	0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 54
	0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 55
	0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 56
	0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 57
	0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 58
	0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 59
	0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 60
	0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 61
	0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 62
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 63
	0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 64
	0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 65
	0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 66
	0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 67
	0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 68
	0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 69
	0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 70
	0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 71
	0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 72
	0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 73
	0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 74
	0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 75
	0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 76
	0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 77
	0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 78
	0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 79
	0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 80
	0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 81
	0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 82
	0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 83
	0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 84
	0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 85
	0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 86
	0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 87
	0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 88
	0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 89
	0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 90
	0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 91
	0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 92
	0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 93
	0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};
#endif

//6*8的点阵
static const unsigned char F6x8[92][6] =		
{
	0x00, 0x00, 0x00, 0x00, 0x00, 0x00,// sp
	0x00, 0x00, 0x00, 0x2f, 0x00, 0x00,// !
	0x00, 0x00, 0x07, 0x00, 0x07, 0x00,// "
	0x00, 0x14, 0x7f, 0x14, 0x7f, 0x14,// #
	0x00, 0x24, 0x2a, 0x7f, 0x2a, 0x12,// $
	0x00, 0x62, 0x64, 0x08, 0x13, 0x23,// %
	0x00, 0x36, 0x49, 0x55, 0x22, 0x50,// &
	0x00, 0x00, 0x05, 0x03, 0x00, 0x00,// '
	0x00, 0x00, 0x1c, 0x22, 0x41, 0x00,// (
	0x00, 0x00, 0x41, 0x22, 0x1c, 0x00,// )
	0x00, 0x14, 0x08, 0x3E, 0x08, 0x14,// *
	0x00, 0x08, 0x08, 0x3E, 0x08, 0x08,// +
	0x00, 0x00, 0x00, 0xA0, 0x60, 0x00,// ,
	0x00, 0x08, 0x08, 0x08, 0x08, 0x08,// -
	0x00, 0x00, 0x60, 0x60, 0x00, 0x00,// .
	0x00, 0x20, 0x10, 0x08, 0x04, 0x02,// /
	0x00, 0x3E, 0x51, 0x49, 0x45, 0x3E,// 0
	0x00, 0x00, 0x42, 0x7F, 0x40, 0x00,// 1
	0x00, 0x42, 0x61, 0x51, 0x49, 0x46,// 2
	0x00, 0x21, 0x41, 0x45, 0x4B, 0x31,// 3
	0x00, 0x18, 0x14, 0x12, 0x7F, 0x10,// 4
	0x00, 0x27, 0x45, 0x45, 0x45, 0x39,// 5
	0x00, 0x3C, 0x4A, 0x49, 0x49, 0x30,// 6
	0x00, 0x01, 0x71, 0x09, 0x05, 0x03,// 7
	0x00, 0x36, 0x49, 0x49, 0x49, 0x36,// 8
	0x00, 0x06, 0x49, 0x49, 0x29, 0x1E,// 9
	0x00, 0x00, 0x36, 0x36, 0x00, 0x00,// :
	0x00, 0x00, 0x56, 0x36, 0x00, 0x00,// ;
	0x00, 0x08, 0x14, 0x22, 0x41, 0x00,// <
	0x00, 0x14, 0x14, 0x14, 0x14, 0x14,// =
	0x00, 0x00, 0x41, 0x22, 0x14, 0x08,// >
	0x00, 0x02, 0x01, 0x51, 0x09, 0x06,// ?
	0x00, 0x32, 0x49, 0x59, 0x51, 0x3E,// @
	0x00, 0x7C, 0x12, 0x11, 0x12, 0x7C,// A
	0x00, 0x7F, 0x49, 0x49, 0x49, 0x36,// B
	0x00, 0x3E, 0x41, 0x41, 0x41, 0x22,// C
	0x00, 0x7F, 0x41, 0x41, 0x22, 0x1C,// D
	0x00, 0x7F, 0x49, 0x49, 0x49, 0x41,// E
	0x00, 0x7F, 0x09, 0x09, 0x09, 0x01,// F
	0x00, 0x3E, 0x41, 0x49, 0x49, 0x7A,// G
	0x00, 0x7F, 0x08, 0x08, 0x08, 0x7F,// H
	0x00, 0x00, 0x41, 0x7F, 0x41, 0x00,// I
	0x00, 0x20, 0x40, 0x41, 0x3F, 0x01,// J
	0x00, 0x7F, 0x08, 0x14, 0x22, 0x41,// K
	0x00, 0x7F, 0x40, 0x40, 0x40, 0x40,// L
	0x00, 0x7F, 0x02, 0x0C, 0x02, 0x7F,// M
	0x00, 0x7F, 0x04, 0x08, 0x10, 0x7F,// N
	0x00, 0x3E, 0x41, 0x41, 0x41, 0x3E,// O
	0x00, 0x7F, 0x09, 0x09, 0x09, 0x06,// P
	0x00, 0x3E, 0x41, 0x51, 0x21, 0x5E,// Q
	0x00, 0x7F, 0x09, 0x19, 0x29, 0x46,// R
	0x00, 0x46, 0x49, 0x49, 0x49, 0x31,// S
	0x00, 0x01, 0x01, 0x7F, 0x01, 0x01,// T
	0x00, 0x3F, 0x40, 0x40, 0x40, 0x3F,// U
	0x00, 0x1F, 0x20, 0x40, 0x20, 0x1F,// V
	0x00, 0x3F, 0x40, 0x38, 0x40, 0x3F,// W
	0x00, 0x63, 0x14, 0x08, 0x14, 0x63,// X
	0x00, 0x07, 0x08, 0x70, 0x08, 0x07,// Y
	0x00, 0x61, 0x51, 0x49, 0x45, 0x43,// Z
	0x00, 0x00, 0x7F, 0x41, 0x41, 0x00,// [
	0x00, 0x55, 0x2A, 0x55, 0x2A, 0x55,// 55
	0x00, 0x00, 0x41, 0x41, 0x7F, 0x00,// ]
	0x00, 0x04, 0x02, 0x01, 0x02, 0x04,// ^
	0x00, 0x40, 0x40, 0x40, 0x40, 0x40,// _
	0x00, 0x00, 0x01, 0x02, 0x04, 0x00,// '
	0x00, 0x20, 0x54, 0x54, 0x54, 0x78,// a
	0x00, 0x7F, 0x48, 0x44, 0x44, 0x38,// b
	0x00, 0x38, 0x44, 0x44, 0x44, 0x20,// c
	0x00, 0x38, 0x44, 0x44, 0x48, 0x7F,// d
	0x00, 0x38, 0x54, 0x54, 0x54, 0x18,// e
	0x00, 0x08, 0x7E, 0x09, 0x01, 0x02,// f
	0x00, 0x18, 0xA4, 0xA4, 0xA4, 0x7C,// g
	0x00, 0x7F, 0x08, 0x04, 0x04, 0x78,// h
	0x00, 0x00, 0x44, 0x7D, 0x40, 0x00,// i
	0x00, 0x40, 0x80, 0x84, 0x7D, 0x00,// j
	0x00, 0x7F, 0x10, 0x28, 0x44, 0x00,// k
	0x00, 0x00, 0x41, 0x7F, 0x40, 0x00,// l
	0x00, 0x7C, 0x04, 0x18, 0x04, 0x78,// m
	0x00, 0x7C, 0x08, 0x04, 0x04, 0x78,// n
	0x00, 0x38, 0x44, 0x44, 0x44, 0x38,// o
	0x00, 0xFC, 0x24, 0x24, 0x24, 0x18,// p
	0x00, 0x18, 0x24, 0x24, 0x18, 0xFC,// q
	0x00, 0x7C, 0x08, 0x04, 0x04, 0x08,// r
	0x00, 0x48, 0x54, 0x54, 0x54, 0x20,// s
	0x00, 0x04, 0x3F, 0x44, 0x40, 0x20,// t
	0x00, 0x3C, 0x40, 0x40, 0x20, 0x7C,// u
	0x00, 0x1C, 0x20, 0x40, 0x20, 0x1C,// v
	0x00, 0x3C, 0x40, 0x30, 0x40, 0x3C,// w
	0x00, 0x44, 0x28, 0x10, 0x28, 0x44,// x
	0x00, 0x1C, 0xA0, 0xA0, 0xA0, 0x7C,// y
	0x00, 0x44, 0x64, 0x54, 0x4C, 0x44,// z
	0x14, 0x14, 0x14, 0x14, 0x14, 0x14,// horiz lines
};

//字转数组
static void _itoa(unsigned int uiNum, unsigned char *buf, unsigned char uiRadix)
{
    unsigned char c, i;
    unsigned char *p, rst[32];

    p = rst;
    for (i = 0; i < 32; i++, p++)
    {
        /* Isolate a digit */
        c = uiNum % uiRadix;
        /* Convert to Ascii */
        *p = c + ((c < 10) ? '0' : '7');
        uiNum /= uiRadix;
        if (!uiNum)
            break;
    }

    for (c = 0; c <= i; c++)
    {
        /* Reverse character order */
        *buf++ = *p--;
    }
    *buf = '\0';
}

//字转数组
static unsigned char * _ltoa(unsigned long l, unsigned char *buf, unsigned char radix)
{
#if defined (__TI_COMPILER_VERSION)
  return ( (unsigned char*)ltoa( l, (char *)buf ) );
#elif defined( __GNUC__ )
  return ( (char*)ltoa( l, buf, radix ) );
#else
  unsigned char tmp1[10] = "", tmp2[10] = "", tmp3[10] = "";
  unsigned short num1, num2, num3;
  unsigned char i;

  buf[0] = '\0';

  if ( radix == 10 )
  {
    num1 = l % 10000;
    num2 = (l / 10000) % 10000;
    num3 = (unsigned short)(l / 100000000);

    if (num3) _itoa(num3, tmp3, 10);
    if (num2) _itoa(num2, tmp2, 10);
    if (num1) _itoa(num1, tmp1, 10);

    if (num3)
    {
      strcpy((char*)buf, (char const*)tmp3);
      for (i = 0; i < 4 - strlen((char const*)tmp2); i++)
        strcat((char*)buf, "0");
    }
    strcat((char*)buf, (char const*)tmp2);
    if (num3 || num2)
    {
      for (i = 0; i < 4 - strlen((char const*)tmp1); i++)
        strcat((char*)buf, "0");
    }
    strcat((char*)buf, (char const*)tmp1);
    if (!num3 && !num2 && !num1)
      strcpy((char*)buf, "0");
  }
  else if ( radix == 16 )
  {
    num1 = l & 0x0000FFFF;
    num2 = l >> 16;

    if (num2) _itoa(num2, tmp2, 16);
    if (num1) _itoa(num1, tmp1, 16);

    if (num2)
    {
      strcpy((char*)buf,(char const*)tmp2);
      for (i = 0; i < 4 - strlen((char const*)tmp1); i++)
        strcat((char*)buf, "0");
    }
    strcat((char*)buf, (char const*)tmp1);
    if (!num2 && !num1)
      strcpy((char*)buf, "0");
  }
  else
    return NULL;

  return buf;
#endif
}

/*********************OLED 延时1ms************************************/
static void OLED_DLY_Ms(unsigned int ms)
{                         
    unsigned int a;
    while(ms)
    {
        a=1800;
        while(a--);
        ms--;
    }
    return;
}

/*********************OLED 写数据************************************/
static void OLED_WrDat(unsigned char dat)     
{
    unsigned char i=8, temp=0;
    OLED_DC_1();  
    for(i=0;i<8;i++) //鍙戦�佷竴涓叓浣嶆暟鎹�
    {
        OLED_SCL_0();  
        
        temp = dat&0x80;
        if (temp == 0)
        {
            OLED_SDA_0();
        }
        else
        {
            OLED_SDA_1();
        }
        OLED_SCL_1();       
        dat<<=1;    
    }
} 

/*********************OLED 写命令************************************/
static void OLED_WrCmd(unsigned char cmd)
{
    unsigned char i=8, temp=0;
    OLED_DC_0();  
    for(i=0;i<8;i++) //鍙戦�佷竴涓叓浣嶆暟鎹�
    { 
        OLED_SCL_0(); 
       
        temp = cmd&0x80;
        if (temp == 0)
        {
            OLED_SDA_0();
        }
        else
        {
            OLED_SDA_1();
        }
        OLED_SCL_1();  
        cmd<<=1;;        
    }     
}

/*********************OLED 设置坐标************************************/
static void OLED_Set_Pos(unsigned char x, unsigned char y) 
{ 
    OLED_WrCmd(0xb0+y);
    OLED_WrCmd(((x&0xf0)>>4)|0x10);
    OLED_WrCmd((x&0x0f)|0x01); 
} 

/*********************OLED 全屏************************************/
static void OLED_Fill(unsigned char bmp_dat) 
{
    unsigned char y,x;
    for(y=0;y<8;y++)
    {
        OLED_WrCmd(0xb0+y);
        OLED_WrCmd(0x01);
        OLED_WrCmd(0x10);
        for(x=0;x<X_WIDTH;x++)
            OLED_WrDat(bmp_dat);
    }
}

/***************功能描述：行填充, y为页范围0～7****************/
static void OLED_FillLine(unsigned char y,unsigned char ch)
{
    unsigned char x;    
    OLED_WrCmd(0xb0+y);
    OLED_WrCmd(0x01);
    OLED_WrCmd(0x10); 
    for(x=0;x<X_WIDTH;x++)
        OLED_WrDat(ch);
}

/*********************OLED 复位************************************/
static void OLED_CLS(void)
{
    unsigned char y,x;    
    for(y=0;y<8;y++)
    {
        OLED_WrCmd(0xb0+y);
        OLED_WrCmd(0x01);
        OLED_WrCmd(0x10); 
        for(x=0;x<X_WIDTH;x++)
            OLED_WrDat(0);
    }
}

/***************功能描述：显示6*8一组标准ASCII字符串    显示的坐标（x,y），y为页范围0～7****************/
static void OLED_P6x8Str(unsigned char x, unsigned char y,unsigned char ch[])
{
    unsigned char c=0,i=0,j=0;      
    while (ch[j]!='\0')
    {    
        c =ch[j]-32;
        if(x>126){x=0;y++;}
        OLED_Set_Pos(x,y);  
        if(c > 0 && c < 92)
        {
            for(i=0;i<6;i++)     
                OLED_WrDat(F6x8[c][i]);  
        }
        x+=6;
        j++;
    }
}

/***********功能描述：显示一行ascii 码?无显示的点阵显示黑色,     y为页的范围0～7*****************/
static void OLED_WriteLine(unsigned char line, const char *pText)
{
    OLED_FillLine(line, 0);                            //鍏堟妸杩欎竴琛屾樉绀烘垚榛戣壊
    OLED_P6x8Str(0, line, (unsigned char *)pText);
}

#if LCD_SUPPORT
/*******************功能描述：显示8*16一组标准ASCII字符串     显示的坐标（x,y），y为页范围0～7****************/
static void OLED_P8x16Str(unsigned char x, unsigned char y,unsigned char ch[])
{
    unsigned char c=0,i=0,j=0;
    while (ch[j]!='\0')
    {    
        c =ch[j]-32;
        if(x>120){x=0;y++;}
        OLED_Set_Pos(x,y);    
        for(i=0;i<8;i++)     
            OLED_WrDat(F8X16[c*16+i]);
        OLED_Set_Pos(x,y+1);    
        for(i=0;i<8;i++)     
            OLED_WrDat(F8X16[c*16+i+8]);  
        x+=8;
        j++;
    }
}

/*****************功能描述：显示16*16点阵  显示的坐标（x,y），y为页范围0～7****************************/
static void OLED_P16x16Ch(unsigned char x, unsigned char y, unsigned char N)
{
    unsigned char wm=0;
    unsigned int adder=32*N;  //      
    OLED_Set_Pos(x , y);
    for(wm = 0;wm < 16;wm++)  //             
    {
        OLED_WrDat(F16x16[adder]);    
        adder += 1;
    }      
    OLED_Set_Pos(x,y + 1); 
    for(wm = 0;wm < 16;wm++) //         
    {
        OLED_WrDat(F16x16[adder]);
        adder += 1;
    }           
}
#endif

/*********************************************************************
 * PUBLIC FUNCTIONS
 */
/*********************************************************************
 * @fn      Board_initOLED
 *
 * @brief   Initialize OLED pins.
 *
 * @param   none
 *
 * @return  none
 */
void Board_initOLED(void)
{
    /* Open LED pins */
    if(OLEDPinHandle == NULL)
    {
        OLEDPinHandle = PIN_open(&OLEDPinState, OLEDPinTable);
    }
 
    //初始化
    OLED_SCL_1();
    OLED_RST_0();
    OLED_DLY_Ms(250);
    OLED_RST_1();	//从上电到下面开始初始化要有足够的时间，即等待RC复位完毕  
 
    OLED_WrCmd(0xae);//--turn off oled panel
    OLED_WrCmd(0x00);//---set low column address
    OLED_WrCmd(0x10);//---set high column address
    OLED_WrCmd(0x40);//--set start line address  Set Mapping RAM Display Start Line (0x00~0x3F)
    OLED_WrCmd(0x81);//--set contrast control register
    OLED_WrCmd(0xcf);// Set SEG Output Current Brightness
    OLED_WrCmd(0xa1);//--Set SEG/Column Mapping     0xa0左右反置 0xa1正常
    OLED_WrCmd(0xc8);//Set COM/Row Scan Direction   0xc0上下反置 0xc8正常
    OLED_WrCmd(0xa6);//--set normal display
    OLED_WrCmd(0xa8);//--set multiplex ratio(1 to 64)
    OLED_WrCmd(0x3f);//--1/64 duty
    OLED_WrCmd(0xd3);//-set display offset    Shift Mapping RAM Counter (0x00~0x3F)
    OLED_WrCmd(0x00);//-not offset
    OLED_WrCmd(0xd5);//--set display clock divide ratio/oscillator frequency
    OLED_WrCmd(0x80);//--set divide ratio, Set Clock as 100 Frames/Sec
    OLED_WrCmd(0xd9);//--set pre-charge period
    OLED_WrCmd(0xf1);//Set Pre-Charge as 15 Clocks & Discharge as 1 Clock
    OLED_WrCmd(0xda);//--set com pins hardware configuration
    OLED_WrCmd(0x12);
    OLED_WrCmd(0xdb);//--set vcomh
    OLED_WrCmd(0x40);//Set VCOM Deselect Level
    OLED_WrCmd(0x20);//-Set Page Addressing Mode (0x00/0x01/0x02)
    OLED_WrCmd(0x02);//
    OLED_WrCmd(0x8d);//--set Charge Pump enable/disable
    OLED_WrCmd(0x14);//--set(0x10) disable
    OLED_WrCmd(0xa4);// Disable Entire Display On (0xa4/0xa5)
    OLED_WrCmd(0xa6);// Disable Inverse Display On (0xa6/a7)
    OLED_WrCmd(0xaf);//--turn on oled panel
    OLED_Fill(0x00); //初始成黑屏
 
    //设置偏移值
    OLED_Set_Pos(0,0);
}

/*********************************************************************
 * @fn      OLED_writeValue
 *
 * @brief   Write a value to the OLED.
 *
 * @param   value  - value that will be displayed
 * @param   radix  - 8, 10, 16
 * @param   line - display options
 *
 * @return  none
 */
void OLED_writeValue(unsigned int value, const unsigned char radix, unsigned char line)
{
	unsigned char buf[HAL_OLED_MAX_BUF];

	_ltoa(value, &buf[0], radix);
	OLED_WriteLine(line, (char*)buf);
}

/*********************************************************************
 * @fn      OLED_writeString
 *
 * @brief   Write a string on the OLED display.
 *
 * @param   str - string to print
 * @param   line - line (page) to write (0-7)
 *
 * @return  void
 */
void OLED_writeString(char *str, unsigned char line)
{
	OLED_WriteLine(line, (char*)str);
}

/*********************************************************************
 * @fn      OLED_writeStringValue
 *
 * @brief   Write a string and value on the OLED display.
 *
 * @param   str - string to print
 * @param   value - value to print
 * @param   format - base of the value to print (2,8,16 etc)
 * @param   line - line (page) to write (0-7)
 *
 * @return  none
 */
void OLED_writeStringValue(char *str, unsigned int value, unsigned char format, unsigned char line)
{
	unsigned char tmpLen;
	unsigned char buf[HAL_OLED_MAX_BUF] = {0};

	tmpLen = (unsigned char)strlen((char*)str);
	memcpy(buf, str, tmpLen);
	buf[tmpLen] = ' ';
	_ltoa(value, &buf[tmpLen+1], format );
	OLED_WriteLine(line, (char*)buf);		
}

/*********************************************************************
 * @fn      OLED_clearLine
 *
 * @brief   Clear  lines if the OLED is on.
 *
 * @param   line - line (page) to write (0-7)
 *
 * @return  none
 */
void OLED_clearLine(unsigned char line)
{
    OLED_FillLine(line, 0);
}

3.2 board_oled.h

#ifndef BOARD_OLED_H
#define BOARD_OLED_H

#ifdef __cplusplus
extern "C" {
#endif

/*********************************************************************
 * INCLUDES
 */

/*********************************************************************
 * EXTERNAL VARIABLES
 */

/*********************************************************************
 * CONSTANTS
 */
 
/*********************************************************************
 * TYPEDEFS
 */
//LCD的可写行
typedef enum
{
    OLED_LINE0 = 0,
    OLED_LINE1,
    OLED_LINE2,
    OLED_LINE3,
    OLED_LINE4,
    OLED_LINE5,
    OLED_LINE6,
    OLED_LINE7,
    OLED_LINE_COUNT
}OLED_LINE;
 
/*********************************************************************
 * MACROS
 */

/*********************************************************************
 * API FUNCTIONS
 */
 
/*********************************************************************
 * @fn      Board_initOLED
 *
 * @brief   Initialize OLED pins.
 *
 * @param   none
 *
 * @return  none
 */
void Board_initOLED(void);

/*********************************************************************
 * @fn      OLED_writeValue
 *
 * @brief   Write a value to the OLED.
 *
 * @param   value  - value that will be displayed
 * @param   radix  - 8, 10, 16
 * @param   line - display options
 *
 * @return  none
 */
void OLED_writeValue(unsigned int value, const unsigned char radix, unsigned char line);

/*********************************************************************
 * @fn      OLED_writeString
 *
 * @brief   Write a string on the OLED display.
 *
 * @param   str - string to print
 * @param   line - line (page) to write (0-7)
 *
 * @return  void
 */
void OLED_writeString(char *str, unsigned char line);

/*********************************************************************
 * @fn      OLED_writeStringValue
 *
 * @brief   Write a string and value on the OLED display.
 *
 * @param   str - string to print
 * @param   value - value to print
 * @param   format - base of the value to print (2,8,16 etc)
 * @param   line - line (page) to write (0-7)
 *
 * @return  none
 */
void OLED_writeStringValue(char *str, unsigned int value, unsigned char format, unsigned char line);

/*********************************************************************
 * @fn      OLED_clearLine
 *
 * @brief   Clear  lines if the OLED is on.
 *
 * @param   line - line (page) to write (0-7)
 *
 * @return  none
 */
void OLED_clearLine(unsigned char line);

/*********************************************************************
*********************************************************************/

#ifdef __cplusplus
}
#endif

#endif /* BOARD_OLED_H */

四、API调用

需包含头文件 board_oled.h

Board_initOLED

功能	初始化OLED引脚
函数定义	void Board_initOLED(void)
参数	无
返回	无

OLED_writeValue

功能	对OLED写入数值
函数定义	void OLED_writeValue(unsigned int value, const unsigned char radix, unsigned char line)
参数1	value：被显示的数值
参数2	radix：8, 10, 16进制
参数3	line：数值被显示所在的行数
返回	无

OLED_writeString

功能	对OLED写入字符串
函数定义	void OLED_writeString(char *str, unsigned char line)
参数1	str：被显示的字符串
参数2	line：数值被显示所在的行数
返回	无

OLED_writeStringValue

功能	对OLED写入字符串和值
函数定义	void OLED_writeStringValue(char *str, unsigned int value, unsigned char format, unsigned char line)
参数1	str：被显示的字符串
参数2	value：被显示的数值
参数3	format：8, 10, 16进制
参数4	line：数值被显示所在的行数
返回	无

OLED_clearLine

功能	清除所在行
函数定义	void OLED_clearLine(unsigned char line)
参数	无
返回	无

五、使用例子

1）添加头文件（例 multi_role.c 中）

#include "board_oled.h"

2）添加初始化代码（multi_role.c 的 multi_role_init 函数末尾中）

// 初始化OLED屏
Board_initOLED();

3）添加显示内容

OLED_writeString("Leung", OLED_LINE0); // 写字符串 
OLED_writeValue(557278427, 10, OLED_LINE1); // 写数据 
OLED_writeStringValue("day:", 31, 10, OLED_LINE2);// 写字符串+数据 
OLED_clearLine(OLED_LINE3); // 清除该行

---

• 由 Leung 写于 2018 年 12 月 26 日

• 参考：【CC2640R2F】香瓜CC2640R2F之LCD