ErrorCode[错误代码]
0x01802007
| Transfer setting[传输设置] |
| Receive data error [接收数据错误] The data received is abnormal. [接收到的数据不正常] The corrective action is as follows: [纠正措施如下：] Review the system, e.g. PLC CPU, module setting and cable status. [ 查看PLC系统，例如 PLC CPU，模块设置和电缆状态。] Check the cable. [检查电缆。] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] |
| <ErrorCode:1802007 [HEX]> |
0x01808003
| Transfer setting[传输设置] |
| Driver not yet started [驱动程序尚未启动] The corrective action is as follows: [纠正措施如下：] The network board driver is not started. [网络板驱动程序未启动] Start the driver. [启用驱动] |
| <ErrorCode:1808003 [HEX]> |
0x01808009
| Transfer setting[传输设置] |
| COM port handle error [COM端口句柄错误] The handle of the COM port cannot be acquired. [无法获取COM端口的句柄。] The COM port object cannot be copied. [无法复制COM端口对象。] The SOCKET object cannot be copied. [无法复制SOCKET对象。] The corrective action is as follows: [纠正措施如下：] Check for an application which uses the COM port. [检测是否有程序占用了COM端口] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] |
| <ErrorCode:1808009 [HEX]> |
0x0180800e
| Transfer setting[传输设置] |
| Shared memory open error [共享内存打开错误] Open processing of shared memory failed. [共享内存的开放处理失败。] The corrective action is follows: [纠正措施如下：] Check whether the GX Simulator has started. [检查GX Simulator是否已启动。] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] |
| <ErrorCode:180800e [HEX]> |
0x01808201
| Transfer setting[传输设置] |
| Send error [发送错误] Data send failed. [数据发送失败] The corrective action is as follows. [纠正措施如下：] Review the system, e.g. PLC CPU, module setting and cable status. [ 查看PLC系统，例如 PLC CPU，模块设置和电缆状态。] Make COM port setting on the control panel of the OS. [在操作系统的控制面板上进行COM端口设置。] Make Ethernet board and protocol settings on the control panel. [在控制面板上进行以太网板和协议设置。] Retry the method. [重试此方法。] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] |
| <ErrorCode:1808201[HEX]> |
0x01808301
| Transfer setting[传输设置] |
| Receive error [接收错误] Data receive failed. [数据接收失败] The corrective action is follows: [纠正措施如下：] Review the system, e.g. PLC CPU, module setting and cable status. [ 查看PLC系统，例如 PLC CPU，模块设置和电缆状态。] Review the time-out value of the property. [检查属性的超时值。] Review the time-out value on the communication settings utility. [查看通信设置实用程序的超时值。] Retry the method. [重试此方法。] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] |
| <ErrorCode:1808301 [HEX]> |
0x0180840a
| Transfer setting[传输设置] |
| Communication control setting error [通讯控制设置错误] The control value of the property is unauthorised. [Control的属性值不在设置范围内。] The corrective action is as follows: [纠正措施如下：] Review the control value of the property. [检查Control的属性值。] Set it again on the communication settings utility. [在communication settings设置区域重新设置。] |
| <ErrorCode:180840a [HEX]> |
0x0180840b
| Transfer setting[传输设置] |
| Time-out error [超时错误] Though the time-out period had elapsed, data could not be received. [虽然超时时间已过，但无法接收数据。] The corrective action is as follows: [纠正措施如下：] Review the time-out value of the property. [检测time out 的属性值] Set it again on the communication settings utility. [在communication settings设置区域重新设置。] Review the system, e.g. PLC CPU, module setting and cable status. [ 查看PLC系统，例如 PLC CPU，模块设置和电缆状态。] Retry the method. [重试此方法。] Perform Close once and execute Open again. [执行一次关闭然后再次打开。] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] |
| <ErrorCode:180840b[HEX]> |
0x01808502
| Transfer setting[传输设置] |
| USB driver connect error [USB驱动程序连接错误] Connection of the USB driver failed. [连接USB驱动程序失败。] The corrective action is as follows: [纠正措施如下：] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] Reinstall MX Component. [重装MX Component ] |
| <ErrorCode:1808502 [HEX]> |
0x04000001
| Transfer setting[传输设置] |
| No command error [没有命令错误] The specified CPU type cannot be used to perform processing. [指定的CPU类型不能用于执行处理。] The corrective action is as follows: [纠正措施如下：] Check the CPU type set to ActCpuType. [检查设置为ActCpuType的CPU类型。] Check whether the system configuration is supported or not. [检查是否支持系统配置。] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] Reinstall MX Component. [重装MX Component ] Set it again on the communication settings utility. [在communication settings设置区域重新设置。] |
| <ErrorCode:4000001 [HEX]> |
0xf2100004
| Transfer setting[传输设置] |
| There is no response from the modem. [调制解调器没有响应。] Causes can be the following: [原因可能如下：] Abnormality in the modem. [调制解调器的异常。] Telephone number setting mistake. [电话号码设置错误。] The corrective action is follows: [纠正措施如下：] Check the status of the modem. [检查调制解调器的状态。] Check the telephone number. [检查电话号码。] If the problem persists even after checking the above points, change the value of the properties set (Properties such as ActConnectionCDWaitTime etc., which set the timings) in case of program settings type and change the contents of the detailed settings that were set using the wizard in case of utility settings type. [如果在检查上述点后问题仍然存在，则在程序设置类型的情况下更改属性集的值（ActConnectionCDWaitTime等属性，设置时间），并更改使用该设置设置的详细设置的内容。 实用程序设置类型的向导。] Exit the program and restart the IBM-PC/AT compatible. [退出程序并重启计算机。] |
| <ErrorCode:f2100004 [HEX]> |
0xf2000006
| Transfer setting[传输设置] |
| The PC modem did not receive the AT command. [PC调制解调器没有收到AT命令。] Causes can be the following: [原因可能如下。] Invalid AT command was specified. [指定了无效的AT命令。] Abnormality in the modem. [调制解调器的异常。] The corrective action is follows: [纠正措施如下：] Check the contents of the AT Command. [检查AT命令的内容。] Check the status of the modem. [检查调制解调器的状态。] |
| <ErrorCode:f2000004 [HEX]> |
PLC Monitor Utility参数设置保存位置
C:\MELSEC\Act\Utl\ ActMon.exe
Regedit[注册表]-x64
| 计算机\HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\MITSUBISHI\SWnD5-ACT\MONUTL\LogicalSt\STECMOPEN |
Regedit[注册表]-x86
| HKEY_LOCAL_MACHINE\SOFTWARE\MITSUBISHI\SWnD5-ACT\MONUTL\LogicalSt\STECMOPEN |
FX3UC
Communication setting[串口通讯设置]
CPU type[CPU类型]
| Item |
HEX |
DEC |
| Q00J |
0x0030 |
48 |
| Q00 |
0x0031 |
49 |
| Q01 |
0x0032 |
50 |
| Q02(H) |
0x0022 |
34 |
| Q06H |
0x0023 |
35 |
| Q12H |
0x0024 |
36 |
| Q25H |
0x0025 |
37 |
| Q12PH |
0x0041 |
65 |
| Q25PH |
0x0042 |
66 |
| Q12PRH |
0x0043 |
67 |
| Q25PRH |
0x0044 |
68 |
| Q02(H)-A |
0x0141 |
321 |
| Q06H-A |
0x0142 |
322 |
| Q2A |
0x0011 |
17 |
| Q2AS(H) |
0x0011 |
17 |
| Q2AS1 |
0x0012 |
18 |
| Q2AS(H)S1 |
0x0012 |
18 |
| Q3A |
0x0013 |
19 |
| Q4A |
0x0014 |
20 |
| Q4AR |
0x0014 |
20 |
| A0J2H |
0x0102 |
258 |
| A1FX |
0x0103 |
259 |
| A1S |
0x0104 |
260 |
| A1S(S1) |
0x0104 |
260 |
| A1SJ |
0x0104 |
260 |
| A1SH |
0x0105 |
261 |
| A1SJH |
0x0105 |
261 |
| A1N |
0x0106 |
262 |
| A2C |
0x0107 |
263 |
| A2CJ |
0x0107 |
263 |
| A2N(S1) |
0x0108 |
264 |
| A2S |
0x0108 |
264 |
| A2S(S1) |
0x0108 |
264 |
| A2SH |
0x0109 |
265 |
| A2SH(S1) |
0x0109 |
265 |
| A3N |
0x010A |
266 |
| A2A(S1) |
0x010C |
268 |
| A3A |
0x010D |
269 |
| A2U(S1) |
0x010E |
270 |
| A2US(S1) |
0x010E |
270 |
| A2AS(S1) |
0x010E |
270 |
| A2AS-S30 |
0x0110 |
272 |
| A2AS-S60 |
0x0110 |
272 |
| A2USH-S1 |
0x010F |
271 |
| A3U |
0x0110 |
272 |
| A4U |
0x0111 |
273 |
| A171SH |
0x0601 |
1537 |
| A172SH |
0x0602 |
1538 |
| A173UH(S1) |
0x0604 |
1540 |
| A273UH(S3) |
0x0603 |
1539 |
| FX0(S) |
0x0201 |
513 |
| FX0N |
0x0202 |
514 |
| FX1 |
0x0203 |
515 |
| FX1S |
0x0206 |
518 |
| FX1N(C) |
0x0207 |
519 |
| FX2(C) |
0x0204 |
516 |
| FXU/FX2C |
0x0204 |
516 |
| FX2N(C) |
0x0205 |
517 |
| FX3UC |
0x0208 |
520 |
Transmission speed [传输速率]
| Item |
HEX |
DEC |
| 9600 |
0x00002580 |
9600 |
| 19200 |
0x00004b00 |
19200 |
| 38400 |
0x00009600 |
38400 |
| 57600 |
0x0000e100 |
57600 |
| 115200 |
0x0001c200 |
115200 |
Control[控制方式]
| Item |
HEX |
DEC |
| DTR Control |
0x0001 |
1 |
| RTS Control |
0x0002 |
2 |
| DTR and RTS Control |
0x0007 |
7 |
| DTR or RTS Control |
0x0008 |
8 |