【IoT】ESP32 Arduino GPIO 使用简析

一、GPIO 中断使用简析

1、中断触发方式

ESP32 Arduino 有以下四种触发方式：

LOW 低电平触发
CHANGE 电平变化
RISING 上升沿触发
FALLING 下降沿触发
HIGH 高电平触发

2、配置中断

在定义中断函数后，需要在 setup 函数配置中断函数

// interrupt=中断通道编号，function=中断函数，mode=中断触发模式
attachInterrupt(interrupt, function, mode);

// pin=中断引脚，function=中断函数，mode=中断触发模式
attachInterrupt(pin, function, mode);

如果在程序运行过程不需要使用外部中断了，可以用中断分离函数来取消这一中断设置：

detachInterrupt(interrupt);
detachInterrupt(Pin);。

3、示例

void setup()
{
  // 初始化日志打印串口
  Serial.begin(115200);
  
  // 配置中断引脚
  pinMode(26, INPUT|PULLUP );

  // 检测到引脚 26 下降沿，触发中断函数 blink
  attachInterrupt(26, blink, FALLING);

  Serial.println("\nstart irq test");
}

void loop()
{

}

// 中断函数
void blink()
{
  Serial.println("IRQ");
}

二、IIC 使用简析

示例：

#include <Wire.h>

void setup() {
  // 启动 i2c 总线
  Wire.begin();

  // 初始化串口
  Serial.begin(9600);
}

int reading = 0;

void loop() {
  // step 1: 启动与从设备 #112 0x70 的数据交互
  Wire.beginTransmission(112);

  // 发送数据
  Wire.write(byte(0x00));
  Wire.write(byte(0x50));

  // 结束通信
  Wire.endTransmission();

  // step 2: 等待读数据
  delay(70);

  // step 3: 读取指定寄存器
  Wire.beginTransmission(112);
  Wire.write(byte(0x02));
  Wire.endTransmission();

  // step 4: 请求读 2 字节数据
  Wire.requestFrom(112, 2);

  // step 5: 接收数据
  if (2 <= Wire.available()) {
    reading = Wire.read();
    reading = reading << 8;
    reading |= Wire.read();
    Serial.println(reading);
  }

  delay(250);
}

三、SPI 使用简析

示例：



/* The ESP32 has four SPi buses, however as of right now only two of
 * them are available to use, HSPI and VSPI. Simply using the SPI API 
 * as illustrated in Arduino examples will use HSPI, leaving VSPI unused.
 * 
 * However if we simply intialise two instance of the SPI class for both
 * of these buses both can be used. However when just using these the Arduino
 * way only will actually be outputting at a time.
 * 
 * Logic analyser capture is in the same folder as this example as
 * "multiple_bus_output.png"
 * 
 * created 30/04/2018 by Alistair Symonds
 */
#include <SPI.h>

static const int spiClk = 1000000; // 1 MHz

//uninitalised pointers to SPI objects
SPIClass * vspi = NULL;
SPIClass * hspi = NULL;

void setup() {
  // 初始化 SPI 实例 VSPI、HSPI
  vspi = new SPIClass(VSPI);
  hspi = new SPIClass(HSPI);
  
  //clock miso mosi ss

  //使用默认 VSPI 引脚：SCLK = 18, MISO = 19, MOSI = 23, SS = 5
  vspi->begin();
  
  // alternatively route through GPIO pins of your choice
  //vspi->begin(0, 2, 4, 33); // SCLK, MISO, MOSI, SS
  
  //使用默认引脚初始化 HSPI
  //SCLK = 14, MISO = 12, MOSI = 13, SS = 15
  hspi->begin(); 

  //alternatively route through GPIO pins
  //hspi->begin(25, 26, 27, 32); //SCLK, MISO, MOSI, SS
  
  // 初始化 ss 片选引脚，默认为低电平
  pinMode(5, OUTPUT); //VSPI SS
  pinMode(15, OUTPUT); //HSPI SS

}

// the loop function runs over and over again until power down or reset
void loop() {
  //use the SPI buses
  vspiCommand();
  hspiCommand();
  delay(100);
}

void vspiCommand() {
  // 模拟数据
  byte data = 0b01010101;

  // 启动 VSPI 传输
  vspi->beginTransaction(SPISettings(spiClk, MSBFIRST, SPI_MODE0));
  digitalWrite(5, LOW);
  vspi->transfer(data);  
  digitalWrite(5, HIGH);
  vspi->endTransaction();
}

void hspiCommand() {
  byte stuff = 0b11001100;
  
  hspi->beginTransaction(SPISettings(spiClk, MSBFIRST, SPI_MODE0));
  digitalWrite(15, LOW);
  hspi->transfer(stuff);
  digitalWrite(15, HIGH);
  hspi->endTransaction();
}

【IoT】ESP32 Arduino GPIO 使用简析

猜你喜欢