CUBE+SD卡读写大量数据/存TXT文件+SPI通信+电路图+源程序+软件解决热插拔

电路图如下（注，通过SPI和SD卡通信；没有在硬件上通过额外引脚判断SD卡是否存在，通过程序检测解决SD热插拔问题）：

CUBE配置：

fatfs，先在cube的Pinout下选上FATFS下的User-defined，fatfs系统指令详解

程序解决热插拔，具体见源代码

uint8_t SD_Init(void)
{
  /* Mount SD Card */
	fres = f_mount(&fs, "", 1);
  if(fres != FR_OK)
	{
		SD_disk_initialize(fs.drv);
		return 0;
	}
  
  /* Open file to write */
  if(f_open(&fil, "pm_data.txt", FA_OPEN_ALWAYS | FA_READ | FA_WRITE) != FR_OK)
    return 0;
	  /* Check free space */
  if(f_getfree("", &fre_clust, &pfs) != FR_OK)
    return 0; 
	else
	{
		total = (uint32_t)((pfs->n_fatent - 2) * pfs->csize * 0.5); //all total is ECF20
    free = (uint32_t)(fre_clust * pfs->csize * 0.5); //all free is ECEC0
		sd_status = free * 1000 / (total / 10);//0.01
		sd_status = 10000 - sd_status ;
		tx_screen[4] = 0x11; tx_screen[5] = 0x10; tx_screen[6] = (sd_status >> 8) & 0xff; tx_screen[7] = sd_status & 0xff; //int sd ->0.01
		HAL_UART_Transmit(&huart5, (uint8_t *)tx_screen, sizeof(tx_screen),0xFFFF);//tx
	}		
    
  /* Free space is less than 1kb */
//  if(free < 1)
//    return 0; 
  
  /* Writing text */
	if(free > 100)//100B
	{
		f_lseek(&fil,fil.fsize);//move the guide
		f_puts("The pm is:", &fil);  //970000/16=60625,one min/time   60625min = 1010hour = 42days
//		f_printf(&fil, "%ld\n", fil.fsize);
		f_printf(&fil, "%ld\n", rx_slave[1]*256 + rx_slave[2]);
//		f_printf(&fil, "%ld\n", sd_status);
	}
	
  
  /* Close file */
  if(f_close(&fil) != FR_OK)
    return 0;  
  
  /* Open file to read */
//  if(f_open(&fil, "pm_data.txt", FA_READ) != FR_OK)
//    return 0;
//  
//  while(f_gets(buffer, sizeof(buffer), &fil))
//  {
//    printf("%s", buffer);
//  }
  
  /* Close file */
//  if(f_close(&fil) != FR_OK)
//    return 0;    
  
  /* Unmount SDCARD */
  if(f_mount(NULL, "", 1) != FR_OK)
    return 0;
	
		return 1;
}

注意事项：不同类型CMD指令不同，本SD卡指令前都加0X40，如下

#define CMD0 (0x40+0) /* GO_IDLE_STATE */
#define CMD1 (0x40+1) /* SEND_OP_COND */
#define CMD8 (0x40+8) /* SEND_IF_COND */
#define CMD9 (0x40+9) /* SEND_CSD */
#define CMD10 (0x40+10) /* SEND_CID */
#define CMD12 (0x40+12) /* STOP_TRANSMISSION */
#define CMD16 (0x40+16) /* SET_BLOCKLEN */
#define CMD17 (0x40+17) /* READ_SINGLE_BLOCK */
#define CMD18 (0x40+18) /* READ_MULTIPLE_BLOCK */
#define CMD23 (0x40+23) /* SET_BLOCK_COUNT */
#define CMD24 (0x40+24) /* WRITE_BLOCK */
#define CMD25 (0x40+25) /* WRITE_MULTIPLE_BLOCK */
#define CMD41 (0x40+41) /* SEND_OP_COND (ACMD) */
#define CMD55 (0x40+55) /* APP_CMD */
#define CMD58 (0x40+58) /* READ_OCR */

写入文件后，必须关闭文件，才能成功

先确保SPI和SD卡通信上，再弄FATFS系统

如果挂载用f_mount(&fs, "", 0);就是稍后挂载，这样，不管有没有SD卡都会显示挂载成功；如果用f_mount(&fs, "", 1);就是立即挂载，这样，没有SD卡就不成功，同原理解决热插拔

按照文件现有大小移动指针，f_lseek(filescr1,filescr1->fptr+filescr1->fsize);这句解决连续存储

这个论坛有介绍

CUBE+SD卡读写大量数据/存TXT文件+SPI通信+电路图+源程序+软件解决热插拔

猜你喜欢