1.cv2.imread（）返回值为NONE
执行pip install --upgrade opencv-python，成功后重新打开python console验证，imread jpg通过，返回的img为正常的MN3数据；至此解决此错误。
修改图片路径：
img = cv2.imread('/usr/apps/python-cv-samples-master/examples/analog-gauge-reader/images/gauge-1.jpg',cv2.IMREAD_UNCHANGED)
2.python3将raw_input和input进行了整合，只有input
gray2 = cv2.cvtColor(img, cv2.COLOR_BGR2GRAY)
'''
Copyright (c) 2017 Intel Corporation.
Licensed under the MIT license. See LICENSE file in the project root for full license information.
'''
import cv2
import numpy as np
#import paho.mqtt.client as mqtt
import time
def avg_circles(circles, b):
avg_x=0
avg_y=0
avg_r=0
for i in range(b):
#optional - average for multiple circles (can happen when a gauge is at a slight angle)
avg_x = avg_x + circles[0][i][0]
avg_y = avg_y + circles[0][i][1]
avg_r = avg_r + circles[0][i][2]
avg_x = int(avg_x/(b))
avg_y = int(avg_y/(b))
avg_r = int(avg_r/(b))
return avg_x, avg_y, avg_r
def dist_2_pts(x1, y1, x2, y2):
#print np.sqrt((x2-x1)^2+(y2-y1)^2)
return np.sqrt((x2 - x1)**2 + (y2 - y1)**2)
def calibrate_gauge(gauge_number, file_type):
'''
This function should be run using a test image in order to calibrate the range available to the dial as well as the
units. It works by first finding the center point and radius of the gauge. Then it draws lines at hard coded intervals
(separation) in degrees. It then prompts the user to enter position in degrees of the lowest possible value of the gauge,
as well as the starting value (which is probably zero in most cases but it won't assume that). It will then ask for the
position in degrees of the largest possible value of the gauge. Finally, it will ask for the units. This assumes that
the gauge is linear (as most probably are).
It will return the min value with angle in degrees (as a tuple), the max value with angle in degree45s (as a tuple),
and the units (as a string).
这个函数用测试图片来校准刻度盘和刻度盘可用的范围单位。需要之前所得的中心点以及半径。然后绘制出刻度。
需要输入表盘读数最小角度，最大角度,最小值，最大值，以及单位(min_angle,max_angle,min_value,max_value,units)
'''
img = cv2.imread('/home/dingzhihui/Downloads/python-cv-samples-master/examples/analog-gauge-reader/images/gauge-%s.%s' %(gauge_number, file_type))
print(img)
height, width = img.shape[:2]
#将图片转为灰度图片
gray = cv2.cvtColor(img, cv2.COLOR_BGR2GRAY) #convert to gray
#gray = cv2.GaussianBlur(gray, (5, 5), 0)
# gray = cv2.medianBlur(gray, 5)
#for testing, output gray image
#cv2.imwrite('gauge-%s-bw.%s' %(gauge_number, file_type),gray)
#detect circles
#restricting the search from 35-48% of the possible radii gives fairly good results across different samples. Remember that
#these are pixel values which correspond to the possible radii search range.
#霍夫圆环检测
#image:8位，单通道图像
#method：定义检测图像中圆的方法。目前唯一实现的方法cv2.HOUGH_GRADIENT。
#dp：累加器分辨率与图像分辨率的反比。dp获取越大，累加器数组越小。
#minDist：检测到的圆的中心，（x,y）坐标之间的最小距离。如果minDist太小，则可能导致检测到多个相邻的圆。如果minDist太大，则可能导致很多圆检测不到。
#param1：用于处理边缘检测的梯度值方法。
#param2：cv2.HOUGH_GRADIENT方法的累加器阈值。阈值越小，检测到的圈子越多。
#minRadius：半径的最小大小（以像素为单位）。
#maxRadius：半径的最大大小（以像素为单位）。
circles = cv2.HoughCircles(gray, cv2.HOUGH_GRADIENT, 1, 20, np.array([]), 100, 50, int(height*0.35), int(height*0.48))
# average found circles, found it to be more accurate than trying to tune HoughCircles parameters to get just the right one
a, b, c = circles.shape
#获取圆的坐标x,y和半径r
x,y,r = avg_circles(circles, b)
#draw center and circle
cv2.circle(img, (x, y), r, (0, 0, 255), 3, cv2.LINE_AA) # draw circle
cv2.circle(img, (x, y), 2, (0, 255, 0), 3, cv2.LINE_AA) # draw center of circle
#for testing, output circles on image
#cv2.imwrite('gauge-%s-circles.%s' % (gauge_number, file_type), img)
#for calibration, plot lines from center going out at every 10 degrees and add marker
#for i from 0 to 36 (every 10 deg)
'''
goes through the motion of a circle and sets x and y values based on the set separation spacing. Also adds text to each
line. These lines and text labels serve as the reference point for the user to enter
NOTE: by default this approach sets 0/360 to be the +x axis (if the image has a cartesian grid in the middle), the addition
(i+9) in the text offset rotates the labels by 90 degrees so 0/360 is at the bottom (-y in cartesian). So this assumes the
gauge is aligned in the image, but it can be adjusted by changing the value of 9 to something else.
根据画出的刻度值，给定x，y的值，并在此位置添加文本信息。
这些刻度和文本标签用作用户输入的参考点
'''
separation = 10.0 #in degrees
interval = int(360 / separation)
p1 = np.zeros((interval,2)) #set empty arrays
p2 = np.zeros((interval,2))
p_text = np.zeros((interval,2))
for i in range(0,interval):
for j in range(0,2):
if (j%2==0):
p1[i][j] = x + 0.9 * r * np.cos(separation * i * 3.14 / 180) #point for lines
else:
p1[i][j] = y + 0.9 * r * np.sin(separation * i * 3.14 / 180)
text_offset_x = 10
text_offset_y = 5
for i in range(0, interval):
for j in range(0, 2):
if (j % 2 == 0):
p2[i][j] = x + r * np.cos(separation * i * 3.14 / 180)
p_text[i][j] = x - text_offset_x + 1.2 * r * np.cos((separation) * (i+9) * 3.14 / 180) #point for text labels, i+9 rotates the labels by 90 degrees
else:
p2[i][j] = y + r * np.sin(separation * i * 3.14 / 180)
p_text[i][j] = y + text_offset_y + 1.2* r * np.sin((separation) * (i+9) * 3.14 / 180) # point for text labels, i+9 rotates the labels by 90 degrees
#add the lines and labels to the image
for i in range(0,interval):
cv2.line(img, (int(p1[i][0]), int(p1[i][1])), (int(p2[i][0]), int(p2[i][1])),(0, 255, 0), 2)
cv2.putText(img, '%s' %(int(i*separation)), (int(p_text[i][0]), int(p_text[i][1])), cv2.FONT_HERSHEY_SIMPLEX, 0.3,(0,0,0),1,cv2.LINE_AA)
cv2.imwrite('gauge-%s-calibration.%s' % (gauge_number, file_type), img)
#get user input on min, max, values, and units
print ('gauge number: %s' %gauge_number)
min_angle = input('Min angle (lowest possible angle of dial) - in degrees: ') #the lowest possible angle
max_angle = input('Max angle (highest possible angle) - in degrees: ') #highest possible angle
min_value = input('Min value: ') #usually zero
max_value = input('Max value: ') #maximum reading of the gauge
units = input('Enter units: ')
#for testing purposes: hardcode and comment out raw_inputs above
# min_angle = 45
# max_angle = 320
# min_value = 0
# max_value = 200
# units = "PSI"
return min_angle, max_angle, min_value, max_value, units, x, y, r
def get_current_value(img, min_angle, max_angle, min_value, max_value, x, y, r, gauge_number, file_type):
#for testing purposes
#img = cv2.imread('gauge-%s.%s' % (gauge_number, file_type))
gray2 = cv2.cvtColor(img, cv2.COLOR_BGR2GRAY)
# Set threshold and maxValue
thresh = 175
maxValue = 255
# for testing purposes, found cv2.THRESH_BINARY_INV to perform the best
# th, dst1 = cv2.threshold(gray2, thresh, maxValue, cv2.THRESH_BINARY);
# th, dst2 = cv2.threshold(gray2, thresh, maxValue, cv2.THRESH_BINARY_INV);
# th, dst3 = cv2.threshold(gray2, thresh, maxValue, cv2.THRESH_TRUNC);
# th, dst4 = cv2.threshold(gray2, thresh, maxValue, cv2.THRESH_TOZERO);
# th, dst5 = cv2.threshold(gray2, thresh, maxValue, cv2.THRESH_TOZERO_INV);
# cv2.imwrite('gauge-%s-dst1.%s' % (gauge_number, file_type), dst1)
# cv2.imwrite('gauge-%s-dst2.%s' % (gauge_number, file_type), dst2)
# cv2.imwrite('gauge-%s-dst3.%s' % (gauge_number, file_type), dst3)
# cv2.imwrite('gauge-%s-dst4.%s' % (gauge_number, file_type), dst4)
# cv2.imwrite('gauge-%s-dst5.%s' % (gauge_number, file_type), dst5)
# apply thresholding which helps for finding lines
th, dst2 = cv2.threshold(gray2, thresh, maxValue, cv2.THRESH_BINARY_INV);
# found Hough Lines generally performs better without Canny / blurring, though there were a couple exceptions where it would only work with Canny / blurring
#dst2 = cv2.medianBlur(dst2, 5)
#dst2 = cv2.Canny(dst2, 50, 150)
#dst2 = cv2.GaussianBlur(dst2, (5, 5), 0)
# for testing, show image after thresholding
cv2.imwrite('gauge-%s-tempdst2.%s' % (gauge_number, file_type), dst2)
# find lines
minLineLength = 10
maxLineGap = 0
lines = cv2.HoughLinesP(image=dst2, rho=3, theta=np.pi / 180, threshold=100,minLineLength=minLineLength, maxLineGap=0) # rho is set to 3 to detect more lines, easier to get more then filter them out later
#for testing purposes, show all found lines
# for i in range(0, len(lines)):
# for x1, y1, x2, y2 in lines[i]:
# cv2.line(img, (x1, y1), (x2, y2), (0, 255, 0), 2)
# cv2.imwrite('gauge-%s-lines-test.%s' %(gauge_number, file_type), img)
# remove all lines outside a given radius
print('lines',lines)
final_line_list = []
#print "radius: %s" %r
diff1LowerBound = 0.15 #diff1LowerBound and diff1UpperBound determine how close the line should be from the center
diff1UpperBound = 0.25
diff2LowerBound = 0.5 #diff2LowerBound and diff2UpperBound determine how close the other point of the line should be to the outside of the gauge
diff2UpperBound = 1.0
for i in range(0, len(lines)):
for x1, y1, x2, y2 in lines[i]:
#print('x1',x1)
#print('y1',y1)
#print('x2',x2)
#print('y2',y2)
diff1 = dist_2_pts(x, y, x1, y1) # x, y is center of circle
#print('diff1',diff1)
diff2 = dist_2_pts(x, y, x2, y2) # x, y is center of circle
#print('diff2', diff2)
#set diff1 to be the smaller (closest to the center) of the two), makes the math easier
if (diff1 > diff2):
temp = diff1
diff1 = diff2
diff2 = temp
# check if line is within an acceptable range
#print('diff1UpperBound*r',diff1UpperBound*r)
#print('diff1LowerBound*r', diff1LowerBound*r)
#print('diff2UpperBound*r', diff2UpperBound*r)
#print('diff2LowerBound*r', diff2LowerBound*r)
if (((diff1<diff1UpperBound*r) and (diff1>diff1LowerBound*r) and (diff2<diff2UpperBound*r)) and (diff2>diff2LowerBound*r)):
print('aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa')
print('diff1UpperBound*r',diff1UpperBound*r)
print('diff1LowerBound*r', diff1LowerBound*r)
print('diff2UpperBound*r', diff2UpperBound*r)
print('diff2LowerBound*r', diff2LowerBound*r)
print('diff1', diff1)
print('diff2', diff2)
line_length = dist_2_pts(x1, y1, x2, y2)
# add to final list
print([x1, y1, x2, y2])
final_line_list.append([x1, y1, x2, y2])
#testing only, show all lines after filtering
# for i in range(0,len(final_line_list)):
# x1 = final_line_list[i][0]
# y1 = final_line_list[i][1]
# x2 = final_line_list[i][2]
# y2 = final_line_list[i][3]
# cv2.line(img, (x1, y1), (x2, y2), (0, 255, 0), 2)
# assumes the first line is the best one
print(final_line_list)
x1 = final_line_list[0][0]
y1 = final_line_list[0][1]
x2 = final_line_list[0][2]
y2 = final_line_list[0][3]
cv2.line(img, (x1, y1), (x2, y2), (0, 255, 0), 2)
#for testing purposes, show the line overlayed on the original image
#cv2.imwrite('gauge-1-test.jpg', img)
cv2.imwrite('gauge-%s-lines-2.%s' % (gauge_number, file_type), img)
#find the farthest point from the center to be what is used to determine the angle
dist_pt_0 = dist_2_pts(x, y, x1, y1)
dist_pt_1 = dist_2_pts(x, y, x2, y2)
if (dist_pt_0 > dist_pt_1):
x_angle = x1 - x
y_angle = y - y1
else:
x_angle = x2 - x
y_angle = y - y2
# take the arc tan of y/x to find the angle
res = np.arctan(np.divide(float(y_angle), float(x_angle)))
#np.rad2deg(res) #coverts to degrees
# print x_angle
# print y_angle
# print res
# print np.rad2deg(res)
#these were determined by trial and error
res = np.rad2deg(res)
if x_angle > 0 and y_angle > 0: #in quadrant I
final_angle = 270 - res
if x_angle < 0 and y_angle > 0: #in quadrant II
final_angle = 90 - res
if x_angle < 0 and y_angle < 0: #in quadrant III
final_angle = 90 - res
if x_angle > 0 and y_angle < 0: #in quadrant IV
final_angle = 270 - res
#print final_angle
old_min = float(min_angle)
old_max = float(max_angle)
new_min = float(min_value)
new_max = float(max_value)
old_value = final_angle
old_range = (old_max - old_min)
new_range = (new_max - new_min)
new_value = (((old_value - old_min) * new_range) / old_range) + new_min
return new_value
def main():
gauge_number = 1
file_type='jpg'
# name the calibration image of your gauge 'gauge-#.jpg', for example 'gauge-5.jpg'. It's written this way so you can easily try multiple images
min_angle, max_angle, min_value, max_value, units, x, y, r = calibrate_gauge(gauge_number, file_type)
print('min_angle=',min_angle)
print('max_angle=',max_angle)
print('min_value=', min_value)
print('max_value=', max_value)
print('units=', units)
print('x=', x)
print('y=', y)
print('r=', r)
#feed an image (or frame) to get the current value, based on the calibration, by default uses same image as calibration
img = cv2.imread('/home/dingzhihui/Downloads/python-cv-samples-master/examples/analog-gauge-reader/images/gauge-%s.%s' % (gauge_number, file_type))
print()
val = get_current_value(img, min_angle, max_angle, min_value, max_value, x, y, r, gauge_number, file_type)
print("Current reading: %s %s" %(val, units))
if __name__=='__main__':
main()