Early into the mine on a snail interstellar mining machine, until the installation is black skirt in use, but also because the OMV has already been installed, after the expiry of experience and see what use is precisely the dual Ethernet ports, this CPU used to do a lot of soft route. So wanted to bring a soft brush LEDE do with the route, there are a lot of people are PVE coat LEDE + black dress, J1900 is not strong, although this use is personal enough. I do not have too many demands on what you want to dual-route and the like, do not play virtual, so I installed a solid line, since you do not move, just install a LEDE. I have here is going to call the shots with a soft routing routing, routing hard to do AP. Routing software for home use, there are more advantages than the hard route, do not worry about the hard route that the hundreds of M memory, but there are many plug-ins, Shuangwai.
There are already too many people write a lot of good articles, and there will be a different operation or an easier way, I am also white, so I'm just here a practical record. for reference only
Preparatory
- x86 devices (this is my snail J1900)
- firmware
- ON
- System disk (larger than 8G on OK I should be here in the garbage msata 16G)
- monitor
Download Firmware
Firmware can be downloaded directly to the official firmware download download, msata my hard drive, so no tool can not be ripped off Windows disk write, so I chose 虚拟机转盘或PE下写盘专用, I chose to start the firmware UEFI mode, will be written in the disk PE.
Write disk need to use physdiskwritethis software, download address below:
Links: https://pan.baidu.com/s/16nQzGnp9Y8JlOVuSDAqiOA extraction code: vc5t
Write disk firmware
Assuming you already have a PE system, the previously downloaded firmware and write disk tool two copied to your PE tray together.
PE startup disk into your machine in x86, U disk boot into PE.
- Formatting system disk
bootDiskGeniussystem disk删除所有分区operation
11556878600_.pic_hd.jpg
Confirmation pop-up window是(Y)
21556878603_.pic_hd.jpg
save Changes
c
After the system disk can be seen empty
51556878610_.pic_hd.jpg - The firmware is written to the system tray
this time to check your firmware PE disk in the drive letter and write disk tool in PE it is how much, I was U,
61556878982_.pic.jpg
Then shortcutwin+Rin the pop-up window to entercmdinto the command line (if you can use another system disk media read on Windows, then you can not make in the PE)
Switch to the firmware of your letter where I was U
After using
physdiskwrite -u 你的固件名称
to brush written into the system tray, for example, I am now called firmware
openwrt-koolshare-mod-v2.30-r10402-51ad900e2c-x86-64-uefi-gpt-squashfs.img.gz
then I brush write command is:
physdiskwrite -u openwrt-koolshare-mod-v2.30-r10402-51ad900e2c-x86-64-uefi-gpt-squashfs.img.gz
After pressing Enter, select the location you want to flash the system disk, you saw what a system disk, do not brush wrong, I was at the 0 position, so I chose 0
Then there will be a prompt for confirmation, after confirmation fill out y, after a carriage return
After Enter to start the firmware brush written into the system tray, and wait patiently, it takes about a minute or two after the success will be the following tips:
This time the firmware flashing is complete, the whole process is complete.
Restart LEDE
Now pull out your PE boot disk, click 重启, and then you will see a lot of brush log in screen
Finally, the brush does not move, so that the following example represents a successful start
After you just tap once on the keyboard, you can see the logo and bash command line interface
Modify LEDE address management
The default management address LEDE is 192.168.1.1, this address is usually light cat's management address, in order not to give rise to a conflict, you need to modify LEDE default management address to another address, directly in just modify the address on the command line
enter the command vim /etc/config/network, then in alphabetical ienter edit mode, the default is 192.168.1.1changed to another address, I am here to change it to 192.168.100.1press after :wq!save and exit, a little rough, then a direct hit enter rebootto restart LEDE.
LEDE into the management interface
This time once again to start the LEDE, you can now monitor off soft routing machine, and after the network cable plugged into a network port routing software, enter LEDE admin interface, working machine browser and enter you just modified LEDE manage my address here192.168.100.1
Username root
password koolshare
- Modify wan dial
if you want to use a dial-up route, then you need to modify your cat is light桥接模式, the dial-up work to the soft route.
Soft route has two Ethernet ports, used to make a wan, used to make a lan port. How settings are not called, just specify a fine.
My mouth is now laneth0, wan mouth iseth1
Into 网络-> 接口-> WANtab, set the PPPoEdial-up, fill your broadband account and password, you can save the application
Wait a little while, to
总览
be able to see the network information
Now you open the page, you should be able to get online.
LEDE really a lot of software plug-center
Author: qinkangdeid
link: https: //www.jianshu.com/p/f6de111f3c34
Source: Jane books
are copyrighted by the author. Commercial reprint please contact the author authorized, non-commercial reprint please indicate the source.