刚才配置了MPLS+E×××，接着在原因配置的基础上增加E×××+VxALN的配置。
一、拓扑图如下:
图中共有4台设备，两台做PE，两台做CE。
两台PE之间配置E×××信令，建立隧道，传输CE端的流量。
CE上有两个vlan ，vlan100和vlan200，用于模拟用户。
配置L2的VxLAN，同vlan间互访
配置L3的VxLAN，不同VLAN间的互访。
CE1 vlan 100 192.168.10.10/24 gateway 192.168.10.254
CE1 vlan 200 192.168.20.10/24 gateway 192.168.20.254
CE2 vlan 100 192.168.10.20/24 gateway 192.168.10.254
CE2 vlan 200 192.168.20.20/24 gateway 192.168.20.254
二、配置步骤
- 配置vxlan前，假设拓扑中三层可以，MPLS，LDP等协议已经配置完成
- L2的LxLAN配置
root@PE1# show protocols bgp | display set
set protocols bgp group ibgp type internal
set protocols bgp group ibgp local-address 1.1.1.1
set protocols bgp group ibgp family inet-*** unicast
set protocols bgp group ibgp family e*** signaling
set protocols bgp group ibgp multipath
set protocols bgp group ibgp neighbor 2.2.2.2
root@PE2# show protocols bgp | display set
set protocols bgp group ibgp type internal
set protocols bgp group ibgp local-address 2.2.2.2
set protocols bgp group ibgp family inet-*** unicast
set protocols bgp group ibgp family e*** signaling
set protocols bgp group ibgp multipath
set protocols bgp group ibgp neighbor 1.1.1.1
- 配置PE上的interface和E×××实例
root@PE2# show interfaces ae0 | display set
set interfaces ae0 unit 0 family bridge interface-mode trunk
set interfaces ae0 unit 0 family bridge vlan-id-list 100
set interfaces ae0 unit 0 family bridge vlan-id-list 200
[edit]
root@PE2# show routing-instances e*** | display set
set routing-instances e*** vtep-source-interface lo0.0
set routing-instances e*** instance-type virtual-switch
set routing-instances e*** interface ae0.0
set routing-instances e*** route-distinguisher 2.2.2.2:1
set routing-instances e*** vrf-target target:65000:1
set routing-instances e*** protocols e*** encapsulation vxlan
set routing-instances e*** protocols e*** extended-vni-list 100
set routing-instances e*** protocols e*** extended-vni-list 200
set routing-instances e*** protocols e*** multicast-mode ingress-replication
set routing-instances e*** protocols e*** default-gateway no-gateway-community
set routing-instances e*** bridge-domains v100 vlan-id 100
set routing-instances e*** bridge-domains v100 vxlan vni 100
set routing-instances e*** bridge-domains v100 vxlan ingress-node-replication
set routing-instances e*** bridge-domains v200 vlan-id 200
set routing-instances e*** bridge-domains v200 vxlan vni 200
set routing-instances e*** bridge-domains v200 vxlan ingress-node-replication
syntax error.
root@PE1# show interfaces ae0 | display set
set interfaces ae0 unit 0 family bridge interface-mode trunk
set interfaces ae0 unit 0 family bridge vlan-id-list 100
set interfaces ae0 unit 0 family bridge vlan-id-list 200
[edit]
root@PE1# show routing-instances e*** | display set
set routing-instances e*** vtep-source-interface lo0.0
set routing-instances e*** instance-type virtual-switch
set routing-instances e*** interface ae0.0
set routing-instances e*** route-distinguisher 1.1.1.1:1
set routing-instances e*** vrf-target target:65000:1
set routing-instances e*** protocols e*** encapsulation vxlan
set routing-instances e*** protocols e*** extended-vni-list 100
set routing-instances e*** protocols e*** extended-vni-list 200
set routing-instances e*** protocols e*** multicast-mode ingress-replication
set routing-instances e*** protocols e*** default-gateway no-gateway-community
set routing-instances e*** bridge-domains v100 vlan-id 100
set routing-instances e*** bridge-domains v100 routing-interface irb.100
set routing-instances e*** bridge-domains v100 vxlan vni 100
set routing-instances e*** bridge-domains v100 vxlan ingress-node-replication
set routing-instances e*** bridge-domains v200 vlan-id 200
set routing-instances e*** bridge-domains v200 routing-interface irb.200
set routing-instances e*** bridge-domains v200 vxlan vni 200
set routing-instances e*** bridge-domains v200 vxlan ingress-node-replication
- 查看bgp状态
root@PE1# run show bgp summary
Groups: 1 Peers: 1 Down peers: 0
Table Tot Paths Act Paths Suppressed History Damp State Pending
bgp.l3***.0
0 0 0 0 0 0
bgp.e***.0
16 16 0 0 0 0
Peer AS InPkt OutPkt OutQ Flaps Last Up/Dwn State|#Active/Received/Accepted/Damped...
2.2.2.2 65000 158 157 0 0 55:02 Establ
bgp.l3***.0: 0/0/0/0
bgp.e***.0: 16/16/16/0
e***.e***.0: 16/16/16/0
__default_e***__.e***.0: 0/0/0/0
[edit]
root@PE1# run show route table bgp.e***.0 match-prefix "3:*"
bgp.e***.0: 16 destinations, 16 routes (16 active, 0 holddown, 0 hidden)
- = Active Route, - = Last Active, * = Both
3:2.2.2.2:1::100::2.2.2.2/248 IM
*[BGP/170] 00:55:08, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
3:2.2.2.2:1::200::2.2.2.2/248 IM
*[BGP/170] 00:55:08, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
[edit]
root@PE1# run show route table bgp.e***.0 match-prefix "2:*"
bgp.e***.0: 16 destinations, 16 routes (16 active, 0 holddown, 0 hidden)
- = Active Route, - = Last Active, * = Both
2:2.2.2.2:1::100::00:00:5e:00:01:01/304 MAC/IP
*[BGP/170] 00:55:11, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::100::00:05:86:71:b7:c0/304 MAC/IP
[BGP/170] 00:01:57, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::100::2c:6b:f5:84:cd:f0/304 MAC/IP
[BGP/170] 00:55:11, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::200::00:00:5e:00:01:01/304 MAC/IP
[BGP/170] 00:55:11, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::200::00:05:86:71:b7:c0/304 MAC/IP
[BGP/170] 00:05:24, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::200::2c:6b:f5:84:cd:f0/304 MAC/IP
[BGP/170] 00:55:11, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::100::00:00:5e:00:01:01::192.168.10.254/304 MAC/IP
[BGP/170] 00:55:11, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::100::00:05:86:71:b7:c0::192.168.10.20/304 MAC/IP
[BGP/170] 00:01:57, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::100::2c:6b:f5:84:cd:f0::192.168.10.252/304 MAC/IP
[BGP/170] 00:55:11, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::200::00:00:5e:00:01:01::192.168.20.254/304 MAC/IP
[BGP/170] 00:55:11, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::200::00:05:86:71:b7:c0::192.168.20.20/304 MAC/IP
[BGP/170] 00:05:24, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
2:2.2.2.2:1::200::2c:6b:f5:84:cd:f0::192.168.20.252/304 MAC/IP
*[BGP/170] 00:55:11, localpref 100, from 2.2.2.2
AS path: I, validation-state: unverified
to 10.0.12.2 via ge-0/0/0.0
to 10.0.21.2 via ge-0/0/1.0
- 查看MAC地址状态
root@PE1# run show bridge mac-table
MAC flags (S -static MAC, D -dynamic MAC, L -locally learned, C -Control MAC
O -OVSDB MAC, SE -Statistics enabled, NM -Non configured MAC, R -Remote PE MAC)
Routing instance : e***
Bridging domain : v100, VLAN : 100
MAC MAC Logical Active
address flags interface source
00:00:5e:00:01:01 DR esi.577 05:00:00:fd:e8:00:00:00:64:00
00:05:86:71:b7:c0 D vtep.32769 2.2.2.2
00:05:86:71:e4:c0 D ae0.0
2c:6b:f5:84:cd:f0 D vtep.32769 2.2.2.2
MAC flags (S -static MAC, D -dynamic MAC, L -locally learned, C -Control MAC
O -OVSDB MAC, SE -Statistics enabled, NM -Non configured MAC, R -Remote PE MAC)
Routing instance : e***
Bridging domain : v200, VLAN : 200
MAC MAC Logical Active
address flags interface source
00:00:5e:00:01:01 DR esi.575 05:00:00:fd:e8:00:00:00:c8:00
00:05:86:71:b7:c0 D vtep.32769 2.2.2.2
00:05:86:71:e4:c0 D ae0.0
2c:6b:f5:84:cd:f0 D vtep.32769 2.2.2.2
[edit]
root@PE1# run show interfaces terse | match vtep
vtep up up
vtep.32768 up up
vtep.32769 up up bridge
[edit]
root@PE1#
5.测试连通性
[edit]
root@CE1# run ping 192.168.10.20 source 192.168.10.10
PING 192.168.10.20 (192.168.10.20): 56 data bytes
64 bytes from 192.168.10.20: icmp_seq=0 ttl=64 time=7.373 ms
^C
--- 192.168.10.20 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/stddev = 7.373/7.373/7.373/0.000 ms
[edit]
root@CE1# ...source 192.168.20.10 routing-instance ce1
PING 192.168.20.20 (192.168.20.20): 56 data bytes
64 bytes from 192.168.20.20: icmp_seq=0 ttl=64 time=86.393 ms
^C
--- 192.168.20.20 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/stddev = 86.393/86.393/86.393/0.000 ms
[edit]
root@CE1#
配置VxLAN 三层网关配置：
[edit]
root@PE1# show interfaces irb | display set
set interfaces irb unit 100 proxy-macip-advertisement
set interfaces irb unit 100 family inet address 192.168.10.251/24 virtual-gateway-address 192.168.10.254
set interfaces irb unit 200 proxy-macip-advertisement
set interfaces irb unit 200 family inet address 192.168.20.251/24 virtual-gateway-address 192.168.20.254
[edit]
root@PE1# show routing-instances e*** bridge-domains | display set
set routing-instances e*** bridge-domains v100 vlan-id 100
set routing-instances e*** bridge-domains v100 routing-interface irb.100
set routing-instances e*** bridge-domains v100 vxlan vni 100
set routing-instances e*** bridge-domains v100 vxlan ingress-node-replication
set routing-instances e*** bridge-domains v200 vlan-id 200
set routing-instances e*** bridge-domains v200 routing-interface irb.200
set routing-instances e*** bridge-domains v200 vxlan vni 200
set routing-instances e*** bridge-domains v200 vxlan ingress-node-replication
[edit]
root@PE2# show interfaces irb | display set
set interfaces irb unit 100 proxy-macip-advertisement
set interfaces irb unit 100 family inet address 192.168.10.252/24 virtual-gateway-address 192.168.10.254
set interfaces irb unit 200 family inet address 192.168.20.252/24 virtual-gateway-address 192.168.20.254
[edit]
root@PE2# show routing-instances e*** bridge-domains | display set
set routing-instances e*** bridge-domains v100 vlan-id 100
set routing-instances e*** bridge-domains v100 routing-interface irb.100
set routing-instances e*** bridge-domains v100 vxlan vni 100
set routing-instances e*** bridge-domains v100 vxlan ingress-node-replication
set routing-instances e*** bridge-domains v200 vlan-id 200
set routing-instances e*** bridge-domains v200 routing-interface irb.200
set routing-instances e*** bridge-domains v200 vxlan vni 200
set routing-instances e*** bridge-domains v200 vxlan ingress-node-replication
查看ARP状态：
Total entries: 11
[edit]
root@PE1# run show arp no-resolve | match irb
00:05:86:71:e4:c0 192.168.10.10 irb.100 [ae0.0] none
00:05:86:71:b7:c0 192.168.10.20 irb.100 [vtep.32769] none
2c:6b:f5:84:cd:f0 192.168.10.252 irb.100 [vtep.32769] none
00:00:5e:00:01:01 192.168.10.254 irb.100 permanent published gateway
00:05:86:71:e4:c0 192.168.20.10 irb.200 [ae0.0] none
00:05:86:71:b7:c0 192.168.20.20 irb.200 [vtep.32769] none
2c:6b:f5:84:cd:f0 192.168.20.252 irb.200 [vtep.32769] none
00:00:5e:00:01:01 192.168.20.254 irb.200 permanent published gateway
[edit]
root@PE1#
[edit]
root@PE2# run show arp no-resolve | match irb
00:05:86:71:e4:c0 192.168.10.10 irb.100 [vtep.32769] none
00:05:86:71:b7:c0 192.168.10.20 irb.100 [ae0.0] none
2c:6b:f5:d1:ce:f0 192.168.10.251 irb.100 [vtep.32769] none
00:00:5e:00:01:01 192.168.10.254 irb.100 permanent published gateway
00:05:86:71:e4:c0 192.168.20.10 irb.200 [vtep.32769] permanent remote
00:05:86:71:b7:c0 192.168.20.20 irb.200 [ae0.0] permanent remote
2c:6b:f5:d1:ce:f0 192.168.20.251 irb.200 [vtep.32769] permanent remote
00:00:5e:00:01:01 192.168.20.254 irb.200 permanent published gateway
[edit]
root@PE2#
测试L3 连通性：
[edit]
root@CE1# run ping 192.168.10.20
PING 192.168.10.20 (192.168.10.20): 56 data bytes
64 bytes from 192.168.10.20: icmp_seq=0 ttl=64 time=9.451 ms
^C
--- 192.168.10.20 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/stddev = 9.451/9.451/9.451/0.000 ms
[edit]
root@CE1# run ping 192.168.20.10
PING 192.168.20.10 (192.168.20.10): 56 data bytes
64 bytes from 192.168.20.10: icmp_seq=0 ttl=63 time=5.845 ms
^C
--- 192.168.20.10 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/stddev = 5.845/5.845/5.845/0.000 ms
[edit]
root@CE1# run ping 192.168.20.20
PING 192.168.20.20 (192.168.20.20): 56 data bytes
64 bytes from 192.168.20.20: icmp_seq=0 ttl=63 time=18.676 ms
^C
--- 192.168.20.20 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/stddev = 18.676/18.676/18.676/0.000 ms
[edit]
root@CE1#
[edit]
root@CE1# run ping 192.168.10.10 routing-instance ce1
PING 192.168.10.10 (192.168.10.10): 56 data bytes
64 bytes from 192.168.10.10: icmp_seq=0 ttl=63 time=26.844 ms
^C
--- 192.168.10.10 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/stddev = 26.844/26.844/26.844/0.000 ms
[edit]
root@CE1# run ping 192.168.10.20 routing-instance ce1
PING 192.168.10.20 (192.168.10.20): 56 data bytes
64 bytes from 192.168.10.20: icmp_seq=0 ttl=63 time=11.732 ms
^C
--- 192.168.10.20 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/stddev = 11.732/11.732/11.732/0.000 ms
[edit]
root@CE1# run ping 192.168.20.20 routing-instance ce1
PING 192.168.20.20 (192.168.20.20): 56 data bytes
64 bytes from 192.168.20.20: icmp_seq=0 ttl=64 time=9.908 ms
^C
--- 192.168.20.20 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max/stddev = 9.908/9.908/9.908/0.000 ms
[edit]
root@CE1#
四、设备的完成配置
PE1配置：
root@PE1# show | display set | no-more
set version 18.1R1.9
set system host-name PE1
set system root-authentication encrypted-password "$6$vr.UFWb6$F30e1qd2fm4Y6YBLzuyykAbYTjQ4axpUOPxnG8QljU1YmD5Hz6TkAHmUQf3hHP3mTXR0bnEns3aVFarvZLweK0"
set system syslog file messages any notice
set system syslog file messages authorization info
set system syslog file interactive-commands interactive-commands any
set chassis aggregated-devices ethernet device-count 8
set chassis fpc 0 pic 0 tunnel-services bandwidth 1g
set chassis fpc 0 lite-mode
set chassis network-services enhanced-ip
set interfaces ge-0/0/0 unit 0 family inet address 10.0.12.1/24
set interfaces ge-0/0/0 unit 0 family mpls
set interfaces ge-0/0/1 unit 0 family inet address 10.0.21.1/24
set interfaces ge-0/0/1 unit 0 family mpls
set interfaces ge-0/0/2 gigether-options 802.3ad ae0
set interfaces ge-0/0/3 gigether-options 802.3ad ae0
set interfaces ae0 unit 0 family bridge interface-mode trunk
set interfaces ae0 unit 0 family bridge vlan-id-list 100
set interfaces ae0 unit 0 family bridge vlan-id-list 200
set interfaces irb unit 100 proxy-macip-advertisement
set interfaces irb unit 100 family inet address 192.168.10.251/24 virtual-gateway-address 192.168.10.254
set interfaces irb unit 200 proxy-macip-advertisement
set interfaces irb unit 200 family inet address 192.168.20.251/24 virtual-gateway-address 192.168.20.254
set interfaces lo0 unit 0 family inet address 1.1.1.1/32
set interfaces tap unit 0
set routing-options router-id 1.1.1.1
set routing-options autonomous-system 65000
set routing-options forwarding-table export load-blance
set protocols mpls interface all
set protocols bgp group ibgp type internal
set protocols bgp group ibgp local-address 1.1.1.1
set protocols bgp group ibgp family inet-*** unicast
set protocols bgp group ibgp family e*** signaling
set protocols bgp group ibgp multipath
set protocols bgp group ibgp neighbor 2.2.2.2
set protocols ospf area 0.0.0.0 interface lo0.0 passive
set protocols ospf area 0.0.0.0 interface ge-0/0/0.0
set protocols ospf area 0.0.0.0 interface ge-0/0/1.0
set protocols ldp interface all
set policy-options policy-statement load-blance then load-balance per-packet
set routing-instances e*** vtep-source-interface lo0.0
set routing-instances e*** instance-type virtual-switch
set routing-instances e*** interface ae0.0
set routing-instances e*** route-distinguisher 1.1.1.1:1
set routing-instances e*** vrf-target target:65000:1
set routing-instances e*** protocols e*** encapsulation vxlan
set routing-instances e*** protocols e*** extended-vni-list 100
set routing-instances e*** protocols e*** extended-vni-list 200
set routing-instances e*** protocols e*** multicast-mode ingress-replication
set routing-instances e*** protocols e*** default-gateway no-gateway-community
set routing-instances e*** bridge-domains v100 vlan-id 100
set routing-instances e*** bridge-domains v100 routing-interface irb.100
set routing-instances e*** bridge-domains v100 vxlan vni 100
set routing-instances e*** bridge-domains v100 vxlan ingress-node-replication
set routing-instances e*** bridge-domains v200 vlan-id 200
set routing-instances e*** bridge-domains v200 routing-interface irb.200
set routing-instances e*** bridge-domains v200 vxlan vni 200
set routing-instances e*** bridge-domains v200 vxlan ingress-node-replication
PE2配置：
root@PE2# show | display set | no-more
set version 18.1R1.9
set system host-name PE2
set system root-authentication encrypted-password "$6$KNzT/UZC$1X6NqsVWkWWwafPSlvxZOTFMYe4prMJ1bWUbtrH4KhN/xjEQeLl8txSncpJYO9DeQgeFz8.hmQiRbFoUzdonD."
set system syslog file messages any notice
set system syslog file messages authorization info
set system syslog file interactive-commands interactive-commands any
set chassis aggregated-devices ethernet device-count 8
set chassis fpc 0 lite-mode
set chassis network-services enhanced-ip
set interfaces ge-0/0/0 unit 0 family inet address 10.0.12.2/24
set interfaces ge-0/0/0 unit 0 family mpls
set interfaces ge-0/0/1 unit 0 family inet address 10.0.21.2/24
set interfaces ge-0/0/1 unit 0 family mpls
set interfaces ge-0/0/2 gigether-options 802.3ad ae0
set interfaces ge-0/0/3 gigether-options 802.3ad ae0
set interfaces ae0 unit 0 family bridge interface-mode trunk
set interfaces ae0 unit 0 family bridge vlan-id-list 100
set interfaces ae0 unit 0 family bridge vlan-id-list 200
set interfaces irb unit 100 proxy-macip-advertisement
set interfaces irb unit 100 family inet address 192.168.10.252/24 virtual-gateway-address 192.168.10.254
set interfaces irb unit 200 family inet address 192.168.20.252/24 virtual-gateway-address 192.168.20.254
set interfaces lo0 unit 0 family inet address 2.2.2.2/32
set interfaces tap unit 0
set routing-options router-id 2.2.2.2
set routing-options autonomous-system 65000
set routing-options forwarding-table export load-blance
set protocols mpls interface all
set protocols bgp group ibgp type internal
set protocols bgp group ibgp local-address 2.2.2.2
set protocols bgp group ibgp family inet-*** unicast
set protocols bgp group ibgp family e*** signaling
set protocols bgp group ibgp multipath
set protocols bgp group ibgp neighbor 1.1.1.1
set protocols ospf area 0.0.0.0 interface lo0.0 passive
set protocols ospf area 0.0.0.0 interface ge-0/0/0.0
set protocols ospf area 0.0.0.0 interface ge-0/0/1.0
set protocols ldp interface all
set policy-options policy-statement load-blance then load-balance per-packet
set routing-instances e*** vtep-source-interface lo0.0
set routing-instances e*** instance-type virtual-switch
set routing-instances e*** interface ae0.0
set routing-instances e*** route-distinguisher 2.2.2.2:1
set routing-instances e*** vrf-target target:65000:1
set routing-instances e*** protocols e*** encapsulation vxlan
set routing-instances e*** protocols e*** extended-vni-list 100
set routing-instances e*** protocols e*** extended-vni-list 200
set routing-instances e*** protocols e*** multicast-mode ingress-replication
set routing-instances e*** protocols e*** default-gateway no-gateway-community
set routing-instances e*** bridge-domains v100 vlan-id 100
set routing-instances e*** bridge-domains v100 routing-interface irb.100
set routing-instances e*** bridge-domains v100 vxlan vni 100
set routing-instances e*** bridge-domains v100 vxlan ingress-node-replication
set routing-instances e*** bridge-domains v200 vlan-id 200
set routing-instances e*** bridge-domains v200 routing-interface irb.200
set routing-instances e*** bridge-domains v200 vxlan vni 200
set routing-instances e*** bridge-domains v200 vxlan ingress-node-replication
CE1配置：
[edit]
root@CE1# show | display set
set version 14.1R1.10
set system host-name CE1
set system root-authentication encrypted-password "$1$53mbzDGK$9Hca7Iwxm0xD/k18JhYaa/"
set system syslog user * any emergency
set system syslog file messages any notice
set system syslog file messages authorization info
set system syslog file interactive-commands interactive-commands any
set chassis aggregated-devices ethernet device-count 8
set interfaces ge-0/0/0 gigether-options 802.3ad ae0
set interfaces ge-0/0/1 gigether-options 802.3ad ae0
set interfaces ae0 flexible-vlan-tagging
set interfaces ae0 unit 100 vlan-id 100
set interfaces ae0 unit 100 family inet address 192.168.10.10/24
set interfaces ae0 unit 200 vlan-id 200
set interfaces ae0 unit 200 family inet address 192.168.20.10/24
set routing-options static route 0.0.0.0/0 next-hop 192.168.10.254
set routing-instances ce1 instance-type virtual-router
set routing-instances ce1 interface ae0.200
set routing-instances ce1 routing-options static route 0.0.0.0/0 next-hop 192.168.20.254
[edit]
root@CE1#
CE2配置：
[edit]
root@CE2# show | no-more |display set
set version 14.1R1.10
set system host-name CE2
set system root-authentication encrypted-password "$1$Lm.K.ooI$tfjWMjodLO6oIbEfGX8m40"
set system syslog user * any emergency
set system syslog file messages any notice
set system syslog file messages authorization info
set system syslog file interactive-commands interactive-commands any
set chassis aggregated-devices ethernet device-count 8
set interfaces ge-0/0/0 gigether-options 802.3ad ae0
set interfaces ge-0/0/1 gigether-options 802.3ad ae0
set interfaces ae0 flexible-vlan-tagging
set interfaces ae0 unit 100 vlan-id 100
set interfaces ae0 unit 100 family inet address 192.168.10.20/24
set interfaces ae0 unit 200 vlan-id 200
set interfaces ae0 unit 200 family inet address 192.168.20.20/24
set routing-options static route 0.0.0.0/0 next-hop 192.168.10.254
set routing-instances ce1 instance-type virtual-router
set routing-instances ce1 interface ae0.200
set routing-instances ce1 routing-options static route 0.0.0.0/0 next-hop 192.168.20.254
[edit]
root@CE2#