模块化编程+LCD1602调试工具——“51单片机”

企业开发 2023-10-02 18:26:15 阅读次数: 0

各位CSDN的uu们你们好呀，小雅兰又来啦，刚刚学完静态数码管显示和动态数码管显示，感觉真不错呢，下面，小雅兰就要开始学习模块化编程以及LCD1602调试工具的知识了，让我们进入51单片机的世界吧！！！

模块化编程

LCD1602调试工具

模块化编程

 

 

右键点击Open document <REGX52.H> ，就会显示出此头文件的内容，这句代码的意思也就是把这部分内容拷贝到此文件下

/*--------------------------------------------------------------------------
AT89X52.H

Header file for the low voltage Flash Atmel AT89C52 and AT89LV52.
Copyright (c) 1988-2002 Keil Elektronik GmbH and Keil Software, Inc.
All rights reserved.
--------------------------------------------------------------------------*/

#ifndef __AT89X52_H__
#define __AT89X52_H__

/*------------------------------------------------
Byte Registers
------------------------------------------------*/
sfr P0      = 0x80;
sfr SP      = 0x81;
sfr DPL     = 0x82;
sfr DPH     = 0x83;
sfr PCON    = 0x87;
sfr TCON    = 0x88;
sfr TMOD    = 0x89;
sfr TL0     = 0x8A;
sfr TL1     = 0x8B;
sfr TH0     = 0x8C;
sfr TH1     = 0x8D;
sfr P1      = 0x90;
sfr SCON    = 0x98;
sfr SBUF    = 0x99;
sfr P2      = 0xA0;
sfr IE      = 0xA8;
sfr P3      = 0xB0;
sfr IP      = 0xB8;
sfr T2CON   = 0xC8;
sfr T2MOD   = 0xC9;
sfr RCAP2L  = 0xCA;
sfr RCAP2H  = 0xCB;
sfr TL2     = 0xCC;
sfr TH2     = 0xCD;
sfr PSW     = 0xD0;
sfr ACC     = 0xE0;
sfr B       = 0xF0;

/*------------------------------------------------
P0 Bit Registers
------------------------------------------------*/
sbit P0_0 = 0x80;
sbit P0_1 = 0x81;
sbit P0_2 = 0x82;
sbit P0_3 = 0x83;
sbit P0_4 = 0x84;
sbit P0_5 = 0x85;
sbit P0_6 = 0x86;
sbit P0_7 = 0x87;

/*------------------------------------------------
PCON Bit Values
------------------------------------------------*/
#define IDL_    0x01

#define STOP_   0x02
#define PD_     0x02    /* Alternate definition */

#define GF0_    0x04
#define GF1_    0x08
#define SMOD_   0x80

/*------------------------------------------------
TCON Bit Registers
------------------------------------------------*/
sbit IT0  = 0x88;
sbit IE0  = 0x89;
sbit IT1  = 0x8A;
sbit IE1  = 0x8B;
sbit TR0  = 0x8C;
sbit TF0  = 0x8D;
sbit TR1  = 0x8E;
sbit TF1  = 0x8F;

/*------------------------------------------------
TMOD Bit Values
------------------------------------------------*/
#define T0_M0_   0x01
#define T0_M1_   0x02
#define T0_CT_   0x04
#define T0_GATE_ 0x08
#define T1_M0_   0x10
#define T1_M1_   0x20
#define T1_CT_   0x40
#define T1_GATE_ 0x80

#define T1_MASK_ 0xF0
#define T0_MASK_ 0x0F

/*------------------------------------------------
P1 Bit Registers
------------------------------------------------*/
sbit P1_0 = 0x90;
sbit P1_1 = 0x91;
sbit P1_2 = 0x92;
sbit P1_3 = 0x93;
sbit P1_4 = 0x94;
sbit P1_5 = 0x95;
sbit P1_6 = 0x96;
sbit P1_7 = 0x97;

sbit T2   = 0x90;       /* External input to Timer/Counter 2, clock out */
sbit T2EX = 0x91;       /* Timer/Counter 2 capture/reload trigger & dir ctl */

/*------------------------------------------------
SCON Bit Registers
------------------------------------------------*/
sbit RI   = 0x98;
sbit TI   = 0x99;
sbit RB8  = 0x9A;
sbit TB8  = 0x9B;
sbit REN  = 0x9C;
sbit SM2  = 0x9D;
sbit SM1  = 0x9E;
sbit SM0  = 0x9F;

/*------------------------------------------------
P2 Bit Registers
------------------------------------------------*/
sbit P2_0 = 0xA0;
sbit P2_1 = 0xA1;
sbit P2_2 = 0xA2;
sbit P2_3 = 0xA3;
sbit P2_4 = 0xA4;
sbit P2_5 = 0xA5;
sbit P2_6 = 0xA6;
sbit P2_7 = 0xA7;

/*------------------------------------------------
IE Bit Registers
------------------------------------------------*/
sbit EX0  = 0xA8;       /* 1=Enable External interrupt 0 */
sbit ET0  = 0xA9;       /* 1=Enable Timer 0 interrupt */
sbit EX1  = 0xAA;       /* 1=Enable External interrupt 1 */
sbit ET1  = 0xAB;       /* 1=Enable Timer 1 interrupt */
sbit ES   = 0xAC;       /* 1=Enable Serial port interrupt */
sbit ET2  = 0xAD;       /* 1=Enable Timer 2 interrupt */

sbit EA   = 0xAF;       /* 0=Disable all interrupts */

/*------------------------------------------------
P3 Bit Registers (Mnemonics & Ports)
------------------------------------------------*/
sbit P3_0 = 0xB0;
sbit P3_1 = 0xB1;
sbit P3_2 = 0xB2;
sbit P3_3 = 0xB3;
sbit P3_4 = 0xB4;
sbit P3_5 = 0xB5;
sbit P3_6 = 0xB6;
sbit P3_7 = 0xB7;

sbit RXD  = 0xB0;       /* Serial data input */
sbit TXD  = 0xB1;       /* Serial data output */
sbit INT0 = 0xB2;       /* External interrupt 0 */
sbit INT1 = 0xB3;       /* External interrupt 1 */
sbit T0   = 0xB4;       /* Timer 0 external input */
sbit T1   = 0xB5;       /* Timer 1 external input */
sbit WR   = 0xB6;       /* External data memory write strobe */
sbit RD   = 0xB7;       /* External data memory read strobe */

/*------------------------------------------------
IP Bit Registers
------------------------------------------------*/
sbit PX0  = 0xB8;
sbit PT0  = 0xB9;
sbit PX1  = 0xBA;
sbit PT1  = 0xBB;
sbit PS   = 0xBC;
sbit PT2  = 0xBD;

/*------------------------------------------------
T2CON Bit Registers
------------------------------------------------*/
sbit CP_RL2= 0xC8;      /* 0=Reload, 1=Capture select */
sbit C_T2 = 0xC9;       /* 0=Timer, 1=Counter */
sbit TR2  = 0xCA;       /* 0=Stop timer, 1=Start timer */
sbit EXEN2= 0xCB;       /* Timer 2 external enable */
sbit TCLK = 0xCC;       /* 0=Serial clock uses Timer 1 overflow, 1=Timer 2 */
sbit RCLK = 0xCD;       /* 0=Serial clock uses Timer 1 overflow, 1=Timer 2 */
sbit EXF2 = 0xCE;       /* Timer 2 external flag */
sbit TF2  = 0xCF;       /* Timer 2 overflow flag */

/*------------------------------------------------
T2MOD Bit Values
------------------------------------------------*/
#define DCEN_   0x01    /* 1=Timer 2 can be configured as up/down counter */
#define T2OE_   0x02    /* Timer 2 output enable */

/*------------------------------------------------
PSW Bit Registers
------------------------------------------------*/
sbit P    = 0xD0;
sbit F1   = 0xD1;
sbit OV   = 0xD2;
sbit RS0  = 0xD3;
sbit RS1  = 0xD4;
sbit F0   = 0xD5;
sbit AC   = 0xD6;
sbit CY   = 0xD7;

/*------------------------------------------------
Interrupt Vectors:
Interrupt Address = (Number * 8) + 3
------------------------------------------------*/
#define IE0_VECTOR    0  /* 0x03 External Interrupt 0 */
#define TF0_VECTOR    1  /* 0x0B Timer 0 */
#define IE1_VECTOR    2  /* 0x13 External Interrupt 1 */
#define TF1_VECTOR    3  /* 0x1B Timer 1 */
#define SIO_VECTOR    4  /* 0x23 Serial port */

#define TF2_VECTOR    5  /* 0x2B Timer 2 */
#define EX2_VECTOR    5  /* 0x2B External Interrupt 2 */

#endif



 

下面，我们来把之前的动态数码管显示的代码模块化一下~~

小雅兰一共是把这些代码封装成了五个文件：

Delay.h的内容：

#ifndef __DELAY_H__
#define __DELAY_H__

void Delay(unsigned char xms);

#endif

Delay.c的内容：

#include <REGX52.H>

void Delay(unsigned char xms)	//@12.000MHz
{
	unsigned char data i, j;
	while(xms)
	{
		i = 2;
		j = 239;
		do
		{
			while (--j);
		} while (--i);
		xms--;
	}
}

Nixie.h的内容：

#ifndef __NIXIE_H__
#define __NIXIE_H__

void Nixie(unsigned char Location,unsigned char Number);

#endif

Nixie.c的内容：

#include <REGX52.H>
#include "Delay.h"
unsigned char NixieTable[]={0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F};
void Nixie(unsigned char Location,unsigned char Number)
{
	switch(Location)
	{
	case 1:
		P2_4=1;
		P2_3=1;
		P2_2=1;
		break;
	case 2:
		P2_4=1;
		P2_3=1;
		P2_2=0;
		break;
	case 3:
		P2_4=1;
		P2_3=0;
		P2_2=1;
		break;
	case 4:
		P2_4=1;
		P2_3=0;
		P2_2=0;
		break;
	case 5:
		P2_4=0;
		P2_3=1;
		P2_2=1;
		break;
	case 6:
		P2_4=0;
		P2_3=1;
		P2_2=0;
		break;
	case 7:
		P2_4=0;
		P2_3=0;
		P2_2=1;
		break;
	case 8:
		P2_4=0;
		P2_3=0;
		P2_2=0;
		break;
	}
	P0=NixieTable[Number];
	Delay(1);
	P0=0x00;
}

main.c的内容：

#include <REGX52.H>
#include "Nixie.h"
void main()
{
	while(1)
	{
		Nixie(1,1);
		Nixie(2,2);
		Nixie(3,3);
		Nixie(4,4);
		Nixie(5,5);
		Nixie(6,6);
	}
}

 LCD1602调试工具

 LCD1602.c的内容：

#include <REGX52.H>

//引脚配置：
sbit LCD_RS=P2^6;
sbit LCD_RW=P2^5;
sbit LCD_EN=P2^7;
#define LCD_DataPort P0

//函数定义：
/**
  * @brief  LCD1602延时函数，12MHz调用可延时1ms
  * @param  无
  * @retval 无
  */
void LCD_Delay()
{
	unsigned char i, j;

	i = 2;
	j = 239;
	do
	{
		while (--j);
	} while (--i);
}

/**
  * @brief  LCD1602写命令
  * @param  Command 要写入的命令
  * @retval 无
  */
void LCD_WriteCommand(unsigned char Command)
{
	LCD_RS=0;
	LCD_RW=0;
	LCD_DataPort=Command;
	LCD_EN=1;
	LCD_Delay();
	LCD_EN=0;
	LCD_Delay();
}

/**
  * @brief  LCD1602写数据
  * @param  Data 要写入的数据
  * @retval 无
  */
void LCD_WriteData(unsigned char Data)
{
	LCD_RS=1;
	LCD_RW=0;
	LCD_DataPort=Data;
	LCD_EN=1;
	LCD_Delay();
	LCD_EN=0;
	LCD_Delay();
}

/**
  * @brief  LCD1602设置光标位置
  * @param  Line 行位置，范围：1~2
  * @param  Column 列位置，范围：1~16
  * @retval 无
  */
void LCD_SetCursor(unsigned char Line,unsigned char Column)
{
	if(Line==1)
	{
		LCD_WriteCommand(0x80|(Column-1));
	}
	else if(Line==2)
	{
		LCD_WriteCommand(0x80|(Column-1+0x40));
	}
}

/**
  * @brief  LCD1602初始化函数
  * @param  无
  * @retval 无
  */
void LCD_Init()
{
	LCD_WriteCommand(0x38);//八位数据接口，两行显示，5*7点阵
	LCD_WriteCommand(0x0c);//显示开，光标关，闪烁关
	LCD_WriteCommand(0x06);//数据读写操作后，光标自动加一，画面不动
	LCD_WriteCommand(0x01);//光标复位，清屏
}

/**
  * @brief  在LCD1602指定位置上显示一个字符
  * @param  Line 行位置，范围：1~2
  * @param  Column 列位置，范围：1~16
  * @param  Char 要显示的字符
  * @retval 无
  */
void LCD_ShowChar(unsigned char Line,unsigned char Column,char Char)
{
	LCD_SetCursor(Line,Column);
	LCD_WriteData(Char);
}

/**
  * @brief  在LCD1602指定位置开始显示所给字符串
  * @param  Line 起始行位置，范围：1~2
  * @param  Column 起始列位置，范围：1~16
  * @param  String 要显示的字符串
  * @retval 无
  */
void LCD_ShowString(unsigned char Line,unsigned char Column,char *String)
{
	unsigned char i;
	LCD_SetCursor(Line,Column);
	for(i=0;String[i]!='\0';i++)
	{
		LCD_WriteData(String[i]);
	}
}

/**
  * @brief  返回值=X的Y次方
  */
int LCD_Pow(int X,int Y)
{
	unsigned char i;
	int Result=1;
	for(i=0;i<Y;i++)
	{
		Result*=X;
	}
	return Result;
}

/**
  * @brief  在LCD1602指定位置开始显示所给数字
  * @param  Line 起始行位置，范围：1~2
  * @param  Column 起始列位置，范围：1~16
  * @param  Number 要显示的数字，范围：0~65535
  * @param  Length 要显示数字的长度，范围：1~5
  * @retval 无
  */
void LCD_ShowNum(unsigned char Line,unsigned char Column,unsigned int Number,unsigned char Length)
{
	unsigned char i;
	LCD_SetCursor(Line,Column);
	for(i=Length;i>0;i--)
	{
		LCD_WriteData(Number/LCD_Pow(10,i-1)%10+'0');
	}
}

/**
  * @brief  在LCD1602指定位置开始以有符号十进制显示所给数字
  * @param  Line 起始行位置，范围：1~2
  * @param  Column 起始列位置，范围：1~16
  * @param  Number 要显示的数字，范围：-32768~32767
  * @param  Length 要显示数字的长度，范围：1~5
  * @retval 无
  */
void LCD_ShowSignedNum(unsigned char Line,unsigned char Column,int Number,unsigned char Length)
{
	unsigned char i;
	unsigned int Number1;
	LCD_SetCursor(Line,Column);
	if(Number>=0)
	{
		LCD_WriteData('+');
		Number1=Number;
	}
	else
	{
		LCD_WriteData('-');
		Number1=-Number;
	}
	for(i=Length;i>0;i--)
	{
		LCD_WriteData(Number1/LCD_Pow(10,i-1)%10+'0');
	}
}

/**
  * @brief  在LCD1602指定位置开始以十六进制显示所给数字
  * @param  Line 起始行位置，范围：1~2
  * @param  Column 起始列位置，范围：1~16
  * @param  Number 要显示的数字，范围：0~0xFFFF
  * @param  Length 要显示数字的长度，范围：1~4
  * @retval 无
  */
void LCD_ShowHexNum(unsigned char Line,unsigned char Column,unsigned int Number,unsigned char Length)
{
	unsigned char i,SingleNumber;
	LCD_SetCursor(Line,Column);
	for(i=Length;i>0;i--)
	{
		SingleNumber=Number/LCD_Pow(16,i-1)%16;
		if(SingleNumber<10)
		{
			LCD_WriteData(SingleNumber+'0');
		}
		else
		{
			LCD_WriteData(SingleNumber-10+'A');
		}
	}
}

/**
  * @brief  在LCD1602指定位置开始以二进制显示所给数字
  * @param  Line 起始行位置，范围：1~2
  * @param  Column 起始列位置，范围：1~16
  * @param  Number 要显示的数字，范围：0~1111 1111 1111 1111
  * @param  Length 要显示数字的长度，范围：1~16
  * @retval 无
  */
void LCD_ShowBinNum(unsigned char Line,unsigned char Column,unsigned int Number,unsigned char Length)
{
	unsigned char i;
	LCD_SetCursor(Line,Column);
	for(i=Length;i>0;i--)
	{
		LCD_WriteData(Number/LCD_Pow(2,i-1)%2+'0');
	}
}

LCD1602.h的内容：

#ifndef __LCD1602_H__
#define __LCD1602_H__

//用户调用函数：
void LCD_Init();
void LCD_ShowChar(unsigned char Line,unsigned char Column,char Char);
void LCD_ShowString(unsigned char Line,unsigned char Column,char *String);
void LCD_ShowNum(unsigned char Line,unsigned char Column,unsigned int Number,unsigned char Length);
void LCD_ShowSignedNum(unsigned char Line,unsigned char Column,int Number,unsigned char Length);
void LCD_ShowHexNum(unsigned char Line,unsigned char Column,unsigned int Number,unsigned char Length);
void LCD_ShowBinNum(unsigned char Line,unsigned char Column,unsigned int Number,unsigned char Length);

#endif

main.c的内容：

#include <REGX52.H>
#include "LCD1602.h"

void main()
{
	LCD_Init();
	LCD_ShowChar(1,1,'K');
	LCD_ShowString(1,3,"Hello");
	LCD_ShowNum(1,9,123,3);
	LCD_ShowSignedNum(1,13,-66,2);
	LCD_ShowHexNum(2,1,0xA8,2);
	LCD_ShowBinNum(2,4,0xAA,8);
	while(1)
	{}
}

 这个调试工具还是非常方便的！！！

好啦，小雅兰的模块化编程和LCD1602调试工具的内容就到这里啦，还要继续加油！！！

猜你喜欢

转载自blog.csdn.net/weixin_74957752/article/details/133493625
今日推荐
火速冲上 GitHub 热榜 —— 开源编程语言、框架哪有这么可爱？
北京人形机器人创新中心发布全球首个纯电驱拟人奔跑的全尺寸人形机器人“天工”
LFOSSA 源来如此公开课 | 掌握云原生未来：CNCF 认证全面攻略与备考秘籍
国产云输入法——仅华为无云端数据上传安全问题
开源日报 | 工业开源项目OGG 1.0；姐姐，你要和我一起配置火狐吗；苹果AI遥遥落后？Fedora 40
开放签电子签章：停止新增，优化体验，前进更进（五一假期前工作）
开源日报 | 中学生开源前端动画引擎；全球首个Llama3 8B中文版开源模型；联想电脑恐出局；Linus讽刺AI炒作
周排行
浏览器对同一域名进行请求的最大并发连接数
React Hook之自定义Hook
【转】MyBatis缓存机制
-Java-泛型
自动化测试常用脚本-发送邮件
LeetCode#859: Buddy Strings
java、Python处理字符串
第二篇の博客
Hadoop伪分布式环境安装
SQL Server进阶（十一）临时表、表变量
每日归档
更多
2024-04-27(56)
2024-04-26(39)
2024-04-25(22)
2024-04-24(36)
2024-04-23(26)
2024-04-22(39)
2024-04-21(0)
2024-04-20(6)
2024-04-19(5)
2024-04-18(0)

代码天地 © 2018 codetd.com

境外服务器   最新电视剧2022