（CSAPP第三版系列）导航篇传送门
4.46
A. 这段代码序列没有正确描述指令popq %rsp的行为。该段代码序列使%rsp的值为(%rsp)+8，而指令popq%rsp执行后，%rsp的值应为(%rsp)。
B. 改写代码序列：
addq $8 , %rsp
movq-8(%rsp) , REG4.48
冒泡排序函数的测试和交换（6-11行）代码：
if(data[i+1] < data[i]){
/*Swap adjacent elements*/
long t = data[i+1];
data[i+1] = data[i];
data[i] = t;
}
对应的Y86-64代码修改为条件转移，代码如下：
mrmovq (%rdx), %r8 rrmovq %rdx, %rsi addq %r10, %rsi mrmovq (%rsi), %rcx rrmovq %rcx, %r10 subq %r8, %r10 rrmovq %rcx, %r10 cmovl %r8, %r10 rmmovq %r10, (%rsi) rrmovq %r8, %r10 cmovl %rcx, %r10 rmmovq %r10, (%rdx)
4.50
Y86-64代码如下：
# Execution begins at address 0
.pos 0
irmovq stack, %rsp # Set up stack pointer
call main # Execute main program
halt # Terminate program
# Array of 8 elements
.align 8
vals:
.quad 0x000000000000
.quad 0x000000000000
.quad 0x000000000000
.quad 0x000000000000
.quad 0x000000000000
.quad 0x000000000000
.quad 0x000000000000
.quad 0x000000000000
jump_table:
.quad L1
.quad L4
.quad L2
.quad L3
.quad L4
.quad L2
main:
irmovq vals, %r12
irmovq $-1,%rdi
call switchv
rmmovq %rax, (%r12)
irmovq $0,%rdi
call switchv
rmmovq %rax, 0x8(%r12)
irmovq $1,%rdi
call switchv
rmmovq %rax, 0x10(%r12)
irmovq $2,%rdi
call switchv
rmmovq %rax, 0x18(%r12)
irmovq $3,%rdi
call switchv
rmmovq %rax, 0x20(%r12)
irmovq $4,%rdi
call switchv
rmmovq %rax, 0x28(%r12)
irmovq $5,%rdi
call switchv
rmmovq %rax, 0x30(%r12)
irmovq $6,%rdi
call switchv
rmmovq %rax, 0x38(%r12)
ret
# long switchv(long idx)
# idx in %rdi
switchv:
rrmovq %rdi, %r8
irmovq $5, %r9
subq %r9, %r8
jg L4
andq %rdi, %rdi
jl L4
irmovq jump_table, %r8
irmovq $8, %r9
irmovq $1, %r10
loop:
subq %r10, %rdi
jl endloop
addq %r9, %r8
jmp loop
endloop:
mrmovq (%r8), %r8
pushq %r8
ret
L1:
irmovq 0xaaa, %rax
ret
L2:
irmovq 0xbbb, %rax
ret
L3:
irmovq 0xccc, %rax
ret
L4:
irmovq 0xddd, %rax #default
ret
# Stack starts here and grows to lower addresses
.pos 0x300 #栈开始地址不能太小
stack:
测试结果截图：
4.52
设计思想：
分析seq-full.hcl，需要对Instr_valid, need_regids, need_valC, srcB, dstE, aluA, aluB进行修改。
bool Instr_valid = icode in{…}; 大括号中所列指令需加上IIADDQ
bool need_regids = icode in{…}; 大括号中所列指令需加上IIADDQ
bool need_valC = icode in{…}; 大括号中所列指令需加上IIADDQ
word srcB = [
icode in {…} : rB; 大括号中所列指令需加上IIADDQ
…
];
word dstE = [
…
icode in {…} : rB; 大括号中所列指令需加上IIADDQ
…
];
word aluA = [
…
icode in {… } : valC; 大括号中所列指令需加上IIADDQ
…
];
word aluB = [
icode in { … } : valB; 大括号中所列指令需加上IIADDQ
…
];添加IIADDQ指令后seq-full.hcl文件：
#/* $begin seq-all-hcl */
####################################################################
# HCL Description of Control for Single Cycle Y86-64 Processor SEQ #
# Copyright (C) Randal E. Bryant, David R. O'Hallaron, 2010 #
####################################################################
## Your task is to implement the iaddq instruction
## The file contains a declaration of the icodes
## for iaddq (IIADDQ)
## Your job is to add the rest of the logic to make it work
####################################################################
# C Include's. Don't alter these #
####################################################################
quote '#include <stdio.h>'
quote '#include "isa.h"'
quote '#include "sim.h"'
quote 'int sim_main(int argc, char *argv[]);'
quote 'word_t gen_pc(){return 0;}'
quote 'int main(int argc, char *argv[])'
quote ' {plusmode=0;return sim_main(argc,argv);}'
####################################################################
# Declarations. Do not change/remove/delete any of these #
####################################################################
##### Symbolic representation of Y86-64 Instruction Codes #############
wordsig INOP 'I_NOP'
wordsig IHALT 'I_HALT'
wordsig IRRMOVQ 'I_RRMOVQ'
wordsig IIRMOVQ 'I_IRMOVQ'
wordsig IRMMOVQ 'I_RMMOVQ'
wordsig IMRMOVQ 'I_MRMOVQ'
wordsig IOPQ 'I_ALU'
wordsig IJXX 'I_JMP'
wordsig ICALL 'I_CALL'
wordsig IRET 'I_RET'
wordsig IPUSHQ 'I_PUSHQ'
wordsig IPOPQ 'I_POPQ'
# Instruction code for iaddq instruction
wordsig IIADDQ 'I_IADDQ'
##### Symbolic represenations of Y86-64 function codes #####
wordsig FNONE 'F_NONE' # Default function code
##### Symbolic representation of Y86-64 Registers referenced explicitly #####
wordsig RRSP 'REG_RSP' # Stack Pointer
wordsig RNONE 'REG_NONE' # Special value indicating "no register"
##### ALU Functions referenced explicitly #####
wordsig ALUADD 'A_ADD' # ALU should add its arguments
##### Possible instruction status values #####
wordsig SAOK 'STAT_AOK' # Normal execution
wordsig SADR 'STAT_ADR' # Invalid memory address
wordsig SINS 'STAT_INS' # Invalid instruction
wordsig SHLT 'STAT_HLT' # Halt instruction encountered
##### Signals that can be referenced by control logic ####################
##### Fetch stage inputs #####
wordsig pc 'pc' # Program counter
##### Fetch stage computations #####
wordsig imem_icode 'imem_icode' # icode field from instruction memory
wordsig imem_ifun 'imem_ifun' # ifun field from instruction memory
wordsig icode 'icode' # Instruction control code
wordsig ifun 'ifun' # Instruction function
wordsig rA 'ra' # rA field from instruction
wordsig rB 'rb' # rB field from instruction
wordsig valC 'valc' # Constant from instruction
wordsig valP 'valp' # Address of following instruction
boolsig imem_error 'imem_error' # Error signal from instruction memory
boolsig instr_valid 'instr_valid' # Is fetched instruction valid?
##### Decode stage computations #####
wordsig valA 'vala' # Value from register A port
wordsig valB 'valb' # Value from register B port
##### Execute stage computations #####
wordsig valE 'vale' # Value computed by ALU
boolsig Cnd 'cond' # Branch test
##### Memory stage computations #####
wordsig valM 'valm' # Value read from memory
boolsig dmem_error 'dmem_error' # Error signal from data memory
####################################################################
# Control Signal Definitions. #
####################################################################
################ Fetch Stage ###################################
# Determine instruction code
word icode = [
imem_error: INOP;
1: imem_icode; # Default: get from instruction memory
];
# Determine instruction function
word ifun = [
imem_error: FNONE;
1: imem_ifun; # Default: get from instruction memory
];
bool instr_valid = icode in
{ INOP, IHALT, IRRMOVQ, IIRMOVQ, IIADDQ, IRMMOVQ, IMRMOVQ,
IOPQ, IJXX, ICALL, IRET, IPUSHQ, IPOPQ };
# Does fetched instruction require a regid byte?
bool need_regids =
icode in { IRRMOVQ, IOPQ, IPUSHQ, IPOPQ,
IIRMOVQ, IIADDQ, IRMMOVQ, IMRMOVQ };
# Does fetched instruction require a constant word?
bool need_valC =
icode in { IIRMOVQ, IIADDQ, IRMMOVQ, IMRMOVQ, IJXX, ICALL };
################ Decode Stage ###################################
## What register should be used as the A source?
word srcA = [
icode in { IRRMOVQ, IRMMOVQ, IOPQ, IPUSHQ } : rA;
icode in { IPOPQ, IRET } : RRSP;
1 : RNONE; # Don't need register
];
## What register should be used as the B source?
word srcB = [
icode in { IOPQ, IRMMOVQ, IMRMOVQ, IIADDQ } : rB;
icode in { IPUSHQ, IPOPQ, ICALL, IRET } : RRSP;
1 : RNONE; # Don't need register
];
## What register should be used as the E destination?
word dstE = [
icode in { IRRMOVQ } && Cnd : rB;
icode in { IIRMOVQ, IOPQ, IIADDQ} : rB;
icode in { IPUSHQ, IPOPQ, ICALL, IRET } : RRSP;
1 : RNONE; # Don't write any register
];
## What register should be used as the M destination?
word dstM = [
icode in { IMRMOVQ, IPOPQ } : rA;
1 : RNONE; # Don't write any register
];
################ Execute Stage ###################################
## Select input A to ALU
word aluA = [
icode in { IRRMOVQ, IOPQ } : valA;
icode in { IIRMOVQ, IRMMOVQ, IMRMOVQ, IIADDQ } : valC;
icode in { ICALL, IPUSHQ } : -8;
icode in { IRET, IPOPQ } : 8;
# Other instructions don't need ALU
];
## Select input B to ALU
word aluB = [
icode in { IRMMOVQ, IMRMOVQ, IOPQ, ICALL,
IPUSHQ, IRET, IPOPQ, IIADDQ } : valB;
icode in { IRRMOVQ, IIRMOVQ } : 0;
# Other instructions don't need ALU
];
## Set the ALU function
word alufun = [
icode == IOPQ : ifun;
1 : ALUADD;
];
## Should the condition codes be updated?
bool set_cc = icode in { IOPQ, IIADDQ };
################ Memory Stage ###################################
## Set read control signal
bool mem_read = icode in { IMRMOVQ, IPOPQ, IRET };
## Set write control signal
bool mem_write = icode in { IRMMOVQ, IPUSHQ, ICALL };
## Select memory address
word mem_addr = [
icode in { IRMMOVQ, IPUSHQ, ICALL, IMRMOVQ } : valE;
icode in { IPOPQ, IRET } : valA;
# Other instructions don't need address
];
## Select memory input data
word mem_data = [
# Value from register
icode in { IRMMOVQ, IPUSHQ } : valA;
# Return PC
icode == ICALL : valP;
# Default: Don't write anything
];
## Determine instruction status
word Stat = [
imem_error || dmem_error : SADR;
!instr_valid: SINS;
icode == IHALT : SHLT;
1 : SAOK;
];
################ Program Counter Update ############################
## What address should instruction be fetched at
word new_pc = [
# Call. Use instruction constant
icode == ICALL : valC;
# Taken branch. Use instruction constant
icode == IJXX && Cnd : valC;
# Completion of RET instruction. Use value from stack
icode == IRET : valM;
# Default: Use incremented PC
1 : valP;
];
#/* $end seq-all-hcl */
模拟器测试结果截图(ISA Check Succeeds)：
4.54
设计思想：
分析pipe-full.hcl，需要对Instr_valid, need_regids, need_valC, srcB, dstE, aluA, aluB, set_cc进行修改。
bool Instr_valid = ficode in{…}; 大括号中所列指令需加上IIADDQ
bool need_regids = ficode in{…}; 大括号中所列指令需加上IIADDQ
bool need_valC = ficode in{…}; 大括号中所列指令需加上IIADDQ
word d_srcB = [
D_icode in {…} : D_rB; 大括号中所列指令需加上IIADDQ
…
];
word d_dstE = [
D_icode in {…} : D_rB; 大括号中所列指令需加上IIADDQ
…
];
word aluA = [
…
E_icode in {… } : E_valC; 大括号中所列指令需加上IIADDQ
…
];
word aluB = [
icode in { … } : E_valB; 大括号中所列指令需加上IIADDQ
…
];
bool set_cc = E_icode == IOPQ && …改为：
boolset_cc = (E_icode == IOPQ || E_icode == IIADDQ) &&…修改后pipe-full.hcl文件：
#/* $begin pipe-all-hcl */
####################################################################
# HCL Description of Control for Pipelined Y86-64 Processor #
# Copyright (C) Randal E. Bryant, David R. O'Hallaron, 2014 #
####################################################################
## Your task is to implement the iaddq instruction
## The file contains a declaration of the icodes
## for iaddq (IIADDQ)
## Your job is to add the rest of the logic to make it work
####################################################################
# C Include's. Don't alter these #
####################################################################
quote '#include <stdio.h>'
quote '#include "isa.h"'
quote '#include "pipeline.h"'
quote '#include "stages.h"'
quote '#include "sim.h"'
quote 'int sim_main(int argc, char *argv[]);'
quote 'int main(int argc, char *argv[]){return sim_main(argc,argv);}'
####################################################################
# Declarations. Do not change/remove/delete any of these #
####################################################################
##### Symbolic representation of Y86-64 Instruction Codes #############
wordsig INOP 'I_NOP'
wordsig IHALT 'I_HALT'
wordsig IRRMOVQ 'I_RRMOVQ'
wordsig IIRMOVQ 'I_IRMOVQ'
wordsig IRMMOVQ 'I_RMMOVQ'
wordsig IMRMOVQ 'I_MRMOVQ'
wordsig IOPQ 'I_ALU'
wordsig IJXX 'I_JMP'
wordsig ICALL 'I_CALL'
wordsig IRET 'I_RET'
wordsig IPUSHQ 'I_PUSHQ'
wordsig IPOPQ 'I_POPQ'
# Instruction code for iaddq instruction
wordsig IIADDQ 'I_IADDQ'
##### Symbolic represenations of Y86-64 function codes #####
wordsig FNONE 'F_NONE' # Default function code
##### Symbolic representation of Y86-64 Registers referenced #####
wordsig RRSP 'REG_RSP' # Stack Pointer
wordsig RNONE 'REG_NONE' # Special value indicating "no register"
##### ALU Functions referenced explicitly ##########################
wordsig ALUADD 'A_ADD' # ALU should add its arguments
##### Possible instruction status values #####
wordsig SBUB 'STAT_BUB' # Bubble in stage
wordsig SAOK 'STAT_AOK' # Normal execution
wordsig SADR 'STAT_ADR' # Invalid memory address
wordsig SINS 'STAT_INS' # Invalid instruction
wordsig SHLT 'STAT_HLT' # Halt instruction encountered
##### Signals that can be referenced by control logic ##############
##### Pipeline Register F ##########################################
wordsig F_predPC 'pc_curr->pc' # Predicted value of PC
##### Intermediate Values in Fetch Stage ###########################
wordsig imem_icode 'imem_icode' # icode field from instruction memory
wordsig imem_ifun 'imem_ifun' # ifun field from instruction memory
wordsig f_icode 'if_id_next->icode' # (Possibly modified) instruction code
wordsig f_ifun 'if_id_next->ifun' # Fetched instruction function
wordsig f_valC 'if_id_next->valc' # Constant data of fetched instruction
wordsig f_valP 'if_id_next->valp' # Address of following instruction
boolsig imem_error 'imem_error' # Error signal from instruction memory
boolsig instr_valid 'instr_valid' # Is fetched instruction valid?
##### Pipeline Register D ##########################################
wordsig D_icode 'if_id_curr->icode' # Instruction code
wordsig D_rA 'if_id_curr->ra' # rA field from instruction
wordsig D_rB 'if_id_curr->rb' # rB field from instruction
wordsig D_valP 'if_id_curr->valp' # Incremented PC
##### Intermediate Values in Decode Stage #########################
wordsig d_srcA 'id_ex_next->srca' # srcA from decoded instruction
wordsig d_srcB 'id_ex_next->srcb' # srcB from decoded instruction
wordsig d_rvalA 'd_regvala' # valA read from register file
wordsig d_rvalB 'd_regvalb' # valB read from register file
##### Pipeline Register E ##########################################
wordsig E_icode 'id_ex_curr->icode' # Instruction code
wordsig E_ifun 'id_ex_curr->ifun' # Instruction function
wordsig E_valC 'id_ex_curr->valc' # Constant data
wordsig E_srcA 'id_ex_curr->srca' # Source A register ID
wordsig E_valA 'id_ex_curr->vala' # Source A value
wordsig E_srcB 'id_ex_curr->srcb' # Source B register ID
wordsig E_valB 'id_ex_curr->valb' # Source B value
wordsig E_dstE 'id_ex_curr->deste' # Destination E register ID
wordsig E_dstM 'id_ex_curr->destm' # Destination M register ID
##### Intermediate Values in Execute Stage #########################
wordsig e_valE 'ex_mem_next->vale' # valE generated by ALU
boolsig e_Cnd 'ex_mem_next->takebranch' # Does condition hold?
wordsig e_dstE 'ex_mem_next->deste' # dstE (possibly modified to be RNONE)
##### Pipeline Register M #########################
wordsig M_stat 'ex_mem_curr->status' # Instruction status
wordsig M_icode 'ex_mem_curr->icode' # Instruction code
wordsig M_ifun 'ex_mem_curr->ifun' # Instruction function
wordsig M_valA 'ex_mem_curr->vala' # Source A value
wordsig M_dstE 'ex_mem_curr->deste' # Destination E register ID
wordsig M_valE 'ex_mem_curr->vale' # ALU E value
wordsig M_dstM 'ex_mem_curr->destm' # Destination M register ID
boolsig M_Cnd 'ex_mem_curr->takebranch' # Condition flag
boolsig dmem_error 'dmem_error' # Error signal from instruction memory
##### Intermediate Values in Memory Stage ##########################
wordsig m_valM 'mem_wb_next->valm' # valM generated by memory
wordsig m_stat 'mem_wb_next->status' # stat (possibly modified to be SADR)
##### Pipeline Register W ##########################################
wordsig W_stat 'mem_wb_curr->status' # Instruction status
wordsig W_icode 'mem_wb_curr->icode' # Instruction code
wordsig W_dstE 'mem_wb_curr->deste' # Destination E register ID
wordsig W_valE 'mem_wb_curr->vale' # ALU E value
wordsig W_dstM 'mem_wb_curr->destm' # Destination M register ID
wordsig W_valM 'mem_wb_curr->valm' # Memory M value
####################################################################
# Control Signal Definitions. #
####################################################################
################ Fetch Stage ###################################
## What address should instruction be fetched at
word f_pc = [
# Mispredicted branch. Fetch at incremented PC
M_icode == IJXX && !M_Cnd : M_valA;
# Completion of RET instruction
W_icode == IRET : W_valM;
# Default: Use predicted value of PC
1 : F_predPC;
];
## Determine icode of fetched instruction
word f_icode = [
imem_error : INOP;
1: imem_icode;
];
# Determine ifun
word f_ifun = [
imem_error : FNONE;
1: imem_ifun;
];
# Is instruction valid?
bool instr_valid = f_icode in
{ INOP, IHALT, IRRMOVQ, IIRMOVQ, IRMMOVQ, IMRMOVQ,
IOPQ, IJXX, ICALL, IRET, IPUSHQ, IPOPQ, IIADDQ };
# Determine status code for fetched instruction
word f_stat = [
imem_error: SADR;
!instr_valid : SINS;
f_icode == IHALT : SHLT;
1 : SAOK;
];
# Does fetched instruction require a regid byte?
bool need_regids =
f_icode in { IRRMOVQ, IOPQ, IPUSHQ, IPOPQ,
IIRMOVQ, IRMMOVQ, IMRMOVQ, IIADDQ };
# Does fetched instruction require a constant word?
bool need_valC =
f_icode in { IIRMOVQ, IRMMOVQ, IMRMOVQ, IJXX, ICALL, IIADDQ };
# Predict next value of PC
word f_predPC = [
f_icode in { IJXX, ICALL } : f_valC;
1 : f_valP;
];
################ Decode Stage ######################################
## What register should be used as the A source?
word d_srcA = [
D_icode in { IRRMOVQ, IRMMOVQ, IOPQ, IPUSHQ } : D_rA;
D_icode in { IPOPQ, IRET } : RRSP;
1 : RNONE; # Don't need register
];
## What register should be used as the B source?
word d_srcB = [
D_icode in { IOPQ, IRMMOVQ, IMRMOVQ, IIADDQ } : D_rB;
D_icode in { IPUSHQ, IPOPQ, ICALL, IRET } : RRSP;
1 : RNONE; # Don't need register
];
## What register should be used as the E destination?
word d_dstE = [
D_icode in { IRRMOVQ, IIRMOVQ, IOPQ, IIADDQ} : D_rB;
D_icode in { IPUSHQ, IPOPQ, ICALL, IRET } : RRSP;
1 : RNONE; # Don't write any register
];
## What register should be used as the M destination?
word d_dstM = [
D_icode in { IMRMOVQ, IPOPQ } : D_rA;
1 : RNONE; # Don't write any register
];
## What should be the A value?
## Forward into decode stage for valA
word d_valA = [
D_icode in { ICALL, IJXX } : D_valP; # Use incremented PC
d_srcA == e_dstE : e_valE; # Forward valE from execute
d_srcA == M_dstM : m_valM; # Forward valM from memory
d_srcA == M_dstE : M_valE; # Forward valE from memory
d_srcA == W_dstM : W_valM; # Forward valM from write back
d_srcA == W_dstE : W_valE; # Forward valE from write back
1 : d_rvalA; # Use value read from register file
];
word d_valB = [
d_srcB == e_dstE : e_valE; # Forward valE from execute
d_srcB == M_dstM : m_valM; # Forward valM from memory
d_srcB == M_dstE : M_valE; # Forward valE from memory
d_srcB == W_dstM : W_valM; # Forward valM from write back
d_srcB == W_dstE : W_valE; # Forward valE from write back
1 : d_rvalB; # Use value read from register file
];
################ Execute Stage #####################################
## Select input A to ALU
word aluA = [
E_icode in { IRRMOVQ, IOPQ } : E_valA;
E_icode in { IIRMOVQ, IRMMOVQ, IMRMOVQ, IIADDQ } : E_valC;
E_icode in { ICALL, IPUSHQ } : -8;
E_icode in { IRET, IPOPQ } : 8;
# Other instructions don't need ALU
];
## Select input B to ALU
word aluB = [
E_icode in { IRMMOVQ, IMRMOVQ, IOPQ, ICALL,
IPUSHQ, IRET, IPOPQ, IIADDQ } : E_valB;
E_icode in { IRRMOVQ, IIRMOVQ } : 0;
# Other instructions don't need ALU
];
## Set the ALU function
word alufun = [
E_icode == IOPQ : E_ifun;
1 : ALUADD;
];
## Should the condition codes be updated?
bool set_cc = (E_icode == IOPQ || E_icode == IIADDQ) &&
# State changes only during normal operation
!m_stat in { SADR, SINS, SHLT } && !W_stat in { SADR, SINS, SHLT };
## Generate valA in execute stage
word e_valA = E_valA; # Pass valA through stage
## Set dstE to RNONE in event of not-taken conditional move
word e_dstE = [
E_icode == IRRMOVQ && !e_Cnd : RNONE;
1 : E_dstE;
];
################ Memory Stage ######################################
## Select memory address
word mem_addr = [
M_icode in { IRMMOVQ, IPUSHQ, ICALL, IMRMOVQ } : M_valE;
M_icode in { IPOPQ, IRET } : M_valA;
# Other instructions don't need address
];
## Set read control signal
bool mem_read = M_icode in { IMRMOVQ, IPOPQ, IRET };
## Set write control signal
bool mem_write = M_icode in { IRMMOVQ, IPUSHQ, ICALL };
#/* $begin pipe-m_stat-hcl */
## Update the status
word m_stat = [
dmem_error : SADR;
1 : M_stat;
];
#/* $end pipe-m_stat-hcl */
## Set E port register ID
word w_dstE = W_dstE;
## Set E port value
word w_valE = W_valE;
## Set M port register ID
word w_dstM = W_dstM;
## Set M port value
word w_valM = W_valM;
## Update processor status
word Stat = [
W_stat == SBUB : SAOK;
1 : W_stat;
];
################ Pipeline Register Control #########################
# Should I stall or inject a bubble into Pipeline Register F?
# At most one of these can be true.
bool F_bubble = 0;
bool F_stall =
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOPQ } &&
E_dstM in { d_srcA, d_srcB } ||
# Stalling at fetch while ret passes through pipeline
IRET in { D_icode, E_icode, M_icode };
# Should I stall or inject a bubble into Pipeline Register D?
# At most one of these can be true.
bool D_stall =
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOPQ } &&
E_dstM in { d_srcA, d_srcB };
bool D_bubble =
# Mispredicted branch
(E_icode == IJXX && !e_Cnd) ||
# Stalling at fetch while ret passes through pipeline
# but not condition for a load/use hazard
!(E_icode in { IMRMOVQ, IPOPQ } && E_dstM in { d_srcA, d_srcB }) &&
IRET in { D_icode, E_icode, M_icode };
# Should I stall or inject a bubble into Pipeline Register E?
# At most one of these can be true.
bool E_stall = 0;
bool E_bubble =
# Mispredicted branch
(E_icode == IJXX && !e_Cnd) ||
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOPQ } &&
E_dstM in { d_srcA, d_srcB};
# Should I stall or inject a bubble into Pipeline Register M?
# At most one of these can be true.
bool M_stall = 0;
# Start injecting bubbles as soon as exception passes through memory stage
bool M_bubble = m_stat in { SADR, SINS, SHLT } || W_stat in { SADR, SINS, SHLT };
# Should I stall or inject a bubble into Pipeline Register W?
bool W_stall = W_stat in { SADR, SINS, SHLT };
bool W_bubble = 0;
#/* $end pipe-all-hcl */
模拟器测试结果截图(ISA Checks Succeed)：
4.56
设计思想：
分析pipe-btfnt.hcl，需要对f_pc, fpredPC, aluA, aluB, D_bubble, E_bubble进行修改。
word f_pc = [
M_icode == IJXX && !M_Cnd : M_valA;
W_icode == IRET : W_valM;
1 : F_predPC;
];
修改为：
word f_pc = [
M_icode == IJXX && M_ifun != UNCOND&& M_valE < M_valA && !M_Cnd : M_valA;
W_icode == IJXX && M_ifun != UNCOND&& M_valE >= M_valA && M_Cnd : M_valE;
W_icode == IRET : W_valM;
1 : F_predPC;
];
word f_predPC = [
f_icode in { IJXX, ICALL } : f_valC;
1 : f_valP;
];
修改为：
word f_predPC = [
f_icode == IJXX && f_ifun != UNCOND&& f_valC < f_valP : f_valC;
f_icode == IJXX && f_ifun != UNCOND&& f_valC >= f_valP : f_valP;
f_icode in { IJXX, ICALL } : f_valC;
1 : f_valP;
];
word aluA = [
…
E_icode in { IIRMOVQ, IRMMOVQ, IMRMOVQ } :E_valC;大括号列指令需加上IJXX
…
];
word aluB = [
…
E_icode in { IRRMOVQ, IIRMOVQ } :0;大括号列指令需加上IJXX
…
];
bool D_bubble =
(E_icode == IJXX && !e_Cnd) || !(E_icode in { IMRMOVQ, IPOPQ } && E_dstM in { d_srcA, d_srcB })&& IRET in { D_icode, E_icode, M_icode };
修改为：
bool D_bubble =
(E_icode == IJXX && E_ifun !=UNCOND && E_valC < E_valA && !e_Cnd) || （E_icode == IJXX && E_ifun !=UNCOND && E_valC >= E_valA && e_Cnd）||! (E_icode in { IMRMOVQ, IPOPQ } && E_dstM in { d_srcA, d_srcB })&& IRET in { D_icode, E_icode, M_icode };
bool E_bubble =
(E_icode == IJXX && !e_Cnd) ||E_icode in { IMRMOVQ, IPOPQ } && E_dstM in { d_srcA, d_srcB };
修改为：
bool E_bubble =
(E_icode== IJXX && E_ifun != UNCOND && E_valC < E_valA &&!e_Cnd) || （E_icode == IJXX && E_ifun != UNCOND && E_valC >=E_valA && e_Cnd）|| E_icode in { IMRMOVQ, IPOPQ} && E_dstM in { d_srcA, d_srcB };修改后pipe-btfnt.hcl文件：
#/* $begin pipe-all-hcl */
####################################################################
# HCL Description of Control for Pipelined Y86-64 Processor #
# Copyright (C) Randal E. Bryant, David R. O'Hallaron, 2014 #
####################################################################
## Your task is to modify the design so that conditional branches are
## predicted as being taken when backward and not-taken when forward
## The code here is nearly identical to that for the normal pipeline.
## Comments starting with keyword "BBTFNT" have been added at places
## relevant to the exercise.
####################################################################
# C Include's. Don't alter these #
####################################################################
quote '#include <stdio.h>'
quote '#include "isa.h"'
quote '#include "pipeline.h"'
quote '#include "stages.h"'
quote '#include "sim.h"'
quote 'int sim_main(int argc, char *argv[]);'
quote 'int main(int argc, char *argv[]){return sim_main(argc,argv);}'
####################################################################
# Declarations. Do not change/remove/delete any of these #
####################################################################
##### Symbolic representation of Y86-64 Instruction Codes #############
wordsig INOP 'I_NOP'
wordsig IHALT 'I_HALT'
wordsig IRRMOVQ 'I_RRMOVQ'
wordsig IIRMOVQ 'I_IRMOVQ'
wordsig IRMMOVQ 'I_RMMOVQ'
wordsig IMRMOVQ 'I_MRMOVQ'
wordsig IOPQ 'I_ALU'
wordsig IJXX 'I_JMP'
wordsig ICALL 'I_CALL'
wordsig IRET 'I_RET'
wordsig IPUSHQ 'I_PUSHQ'
wordsig IPOPQ 'I_POPQ'
##### Symbolic represenations of Y86-64 function codes #####
wordsig FNONE 'F_NONE' # Default function code
##### Symbolic representation of Y86-64 Registers referenced #####
wordsig RRSP 'REG_RSP' # Stack Pointer
wordsig RNONE 'REG_NONE' # Special value indicating "no register"
##### ALU Functions referenced explicitly ##########################
wordsig ALUADD 'A_ADD' # ALU should add its arguments
## BBTFNT: For modified branch prediction, need to distinguish
## conditional vs. unconditional branches
##### Jump conditions referenced explicitly
wordsig UNCOND 'C_YES' # Unconditional transfer
##### Possible instruction status values #####
wordsig SBUB 'STAT_BUB' # Bubble in stage
wordsig SAOK 'STAT_AOK' # Normal execution
wordsig SADR 'STAT_ADR' # Invalid memory address
wordsig SINS 'STAT_INS' # Invalid instruction
wordsig SHLT 'STAT_HLT' # Halt instruction encountered
##### Signals that can be referenced by control logic ##############
##### Pipeline Register F ##########################################
wordsig F_predPC 'pc_curr->pc' # Predicted value of PC
##### Intermediate Values in Fetch Stage ###########################
wordsig imem_icode 'imem_icode' # icode field from instruction memory
wordsig imem_ifun 'imem_ifun' # ifun field from instruction memory
wordsig f_icode 'if_id_next->icode' # (Possibly modified) instruction code
wordsig f_ifun 'if_id_next->ifun' # Fetched instruction function
wordsig f_valC 'if_id_next->valc' # Constant data of fetched instruction
wordsig f_valP 'if_id_next->valp' # Address of following instruction
boolsig imem_error 'imem_error' # Error signal from instruction memory
boolsig instr_valid 'instr_valid' # Is fetched instruction valid?
##### Pipeline Register D ##########################################
wordsig D_icode 'if_id_curr->icode' # Instruction code
wordsig D_rA 'if_id_curr->ra' # rA field from instruction
wordsig D_rB 'if_id_curr->rb' # rB field from instruction
wordsig D_valP 'if_id_curr->valp' # Incremented PC
##### Intermediate Values in Decode Stage #########################
wordsig d_srcA 'id_ex_next->srca' # srcA from decoded instruction
wordsig d_srcB 'id_ex_next->srcb' # srcB from decoded instruction
wordsig d_rvalA 'd_regvala' # valA read from register file
wordsig d_rvalB 'd_regvalb' # valB read from register file
##### Pipeline Register E ##########################################
wordsig E_icode 'id_ex_curr->icode' # Instruction code
wordsig E_ifun 'id_ex_curr->ifun' # Instruction function
wordsig E_valC 'id_ex_curr->valc' # Constant data
wordsig E_srcA 'id_ex_curr->srca' # Source A register ID
wordsig E_valA 'id_ex_curr->vala' # Source A value
wordsig E_srcB 'id_ex_curr->srcb' # Source B register ID
wordsig E_valB 'id_ex_curr->valb' # Source B value
wordsig E_dstE 'id_ex_curr->deste' # Destination E register ID
wordsig E_dstM 'id_ex_curr->destm' # Destination M register ID
##### Intermediate Values in Execute Stage #########################
wordsig e_valE 'ex_mem_next->vale' # valE generated by ALU
boolsig e_Cnd 'ex_mem_next->takebranch' # Does condition hold?
wordsig e_dstE 'ex_mem_next->deste' # dstE (possibly modified to be RNONE)
##### Pipeline Register M #########################
wordsig M_stat 'ex_mem_curr->status' # Instruction status
wordsig M_icode 'ex_mem_curr->icode' # Instruction code
wordsig M_ifun 'ex_mem_curr->ifun' # Instruction function
wordsig M_valA 'ex_mem_curr->vala' # Source A value
wordsig M_dstE 'ex_mem_curr->deste' # Destination E register ID
wordsig M_valE 'ex_mem_curr->vale' # ALU E value
wordsig M_dstM 'ex_mem_curr->destm' # Destination M register ID
boolsig M_Cnd 'ex_mem_curr->takebranch' # Condition flag
boolsig dmem_error 'dmem_error' # Error signal from instruction memory
##### Intermediate Values in Memory Stage ##########################
wordsig m_valM 'mem_wb_next->valm' # valM generated by memory
wordsig m_stat 'mem_wb_next->status' # stat (possibly modified to be SADR)
##### Pipeline Register W ##########################################
wordsig W_stat 'mem_wb_curr->status' # Instruction status
wordsig W_icode 'mem_wb_curr->icode' # Instruction code
wordsig W_dstE 'mem_wb_curr->deste' # Destination E register ID
wordsig W_valE 'mem_wb_curr->vale' # ALU E value
wordsig W_dstM 'mem_wb_curr->destm' # Destination M register ID
wordsig W_valM 'mem_wb_curr->valm' # Memory M value
####################################################################
# Control Signal Definitions. #
####################################################################
################ Fetch Stage ###################################
## What address should instruction be fetched at
word f_pc = [
# Mispredicted branch. Fetch at incremented PC
# backward
M_icode == IJXX && M_ifun != UNCOND && M_valE < M_valA && !M_Cnd : M_valA;
# forward
M_icode == IJXX && M_ifun != UNCOND && M_valE >= M_valA && M_Cnd : M_valE;
# Completion of RET instruction
W_icode == IRET : W_valM;
# Default: Use predicted value of PC
1 : F_predPC;
];
## Determine icode of fetched instruction
word f_icode = [
imem_error : INOP;
1: imem_icode;
];
# Determine ifun
word f_ifun = [
imem_error : FNONE;
1: imem_ifun;
];
# Is instruction valid?
bool instr_valid = f_icode in
{ INOP, IHALT, IRRMOVQ, IIRMOVQ, IRMMOVQ, IMRMOVQ,
IOPQ, IJXX, ICALL, IRET, IPUSHQ, IPOPQ };
# Determine status code for fetched instruction
word f_stat = [
imem_error: SADR;
!instr_valid : SINS;
f_icode == IHALT : SHLT;
1 : SAOK;
];
# Does fetched instruction require a regid byte?
bool need_regids =
f_icode in { IRRMOVQ, IOPQ, IPUSHQ, IPOPQ,
IIRMOVQ, IRMMOVQ, IMRMOVQ };
# Does fetched instruction require a constant word?
bool need_valC =
f_icode in { IIRMOVQ, IRMMOVQ, IMRMOVQ, IJXX, ICALL };
# Predict next value of PC
word f_predPC = [
# BBTFNT: This is where you'll change the branch prediction rule
f_icode == IJXX && f_ifun != UNCOND && f_valC < f_valP : f_valC;
f_icode == IJXX && f_ifun != UNCOND && f_valC >= f_valP : f_valP;
f_icode in { IJXX, ICALL } : f_valC;
1 : f_valP;
];
################ Decode Stage ######################################
## What register should be used as the A source?
word d_srcA = [
D_icode in { IRRMOVQ, IRMMOVQ, IOPQ, IPUSHQ } : D_rA;
D_icode in { IPOPQ, IRET } : RRSP;
1 : RNONE; # Don't need register
];
## What register should be used as the B source?
word d_srcB = [
D_icode in { IOPQ, IRMMOVQ, IMRMOVQ } : D_rB;
D_icode in { IPUSHQ, IPOPQ, ICALL, IRET } : RRSP;
1 : RNONE; # Don't need register
];
## What register should be used as the E destination?
word d_dstE = [
D_icode in { IRRMOVQ, IIRMOVQ, IOPQ} : D_rB;
D_icode in { IPUSHQ, IPOPQ, ICALL, IRET } : RRSP;
1 : RNONE; # Don't write any register
];
## What register should be used as the M destination?
word d_dstM = [
D_icode in { IMRMOVQ, IPOPQ } : D_rA;
1 : RNONE; # Don't write any register
];
## What should be the A value?
## Forward into decode stage for valA
word d_valA = [
D_icode in { ICALL, IJXX } : D_valP; # Use incremented PC
d_srcA == e_dstE : e_valE; # Forward valE from execute
d_srcA == M_dstM : m_valM; # Forward valM from memory
d_srcA == M_dstE : M_valE; # Forward valE from memory
d_srcA == W_dstM : W_valM; # Forward valM from write back
d_srcA == W_dstE : W_valE; # Forward valE from write back
1 : d_rvalA; # Use value read from register file
];
word d_valB = [
d_srcB == e_dstE : e_valE; # Forward valE from execute
d_srcB == M_dstM : m_valM; # Forward valM from memory
d_srcB == M_dstE : M_valE; # Forward valE from memory
d_srcB == W_dstM : W_valM; # Forward valM from write back
d_srcB == W_dstE : W_valE; # Forward valE from write back
1 : d_rvalB; # Use value read from register file
];
################ Execute Stage #####################################
# BBTFNT: When some branches are predicted as not-taken, you need some
# way to get valC into pipeline register M, so that
# you can correct for a mispredicted branch.
## Select input A to ALU
word aluA = [
E_icode in { IRRMOVQ, IOPQ } : E_valA;
E_icode in { IIRMOVQ, IRMMOVQ, IMRMOVQ, IJXX } : E_valC;
E_icode in { ICALL, IPUSHQ } : -8;
E_icode in { IRET, IPOPQ } : 8;
# Other instructions don't need ALU
];
## Select input B to ALU
word aluB = [
E_icode in { IRMMOVQ, IMRMOVQ, IOPQ, ICALL,
IPUSHQ, IRET, IPOPQ } : E_valB;
E_icode in { IRRMOVQ, IIRMOVQ, IJXX } : 0;
# Other instructions don't need ALU
];
## Set the ALU function
word alufun = [
E_icode == IOPQ : E_ifun;
1 : ALUADD;
];
## Should the condition codes be updated?
bool set_cc = E_icode == IOPQ &&
# State changes only during normal operation
!m_stat in { SADR, SINS, SHLT } && !W_stat in { SADR, SINS, SHLT };
## Generate valA in execute stage
word e_valA = E_valA; # Pass valA through stage
## Set dstE to RNONE in event of not-taken conditional move
word e_dstE = [
E_icode == IRRMOVQ && !e_Cnd : RNONE;
1 : E_dstE;
];
################ Memory Stage ######################################
## Select memory address
word mem_addr = [
M_icode in { IRMMOVQ, IPUSHQ, ICALL, IMRMOVQ } : M_valE;
M_icode in { IPOPQ, IRET } : M_valA;
# Other instructions don't need address
];
## Set read control signal
bool mem_read = M_icode in { IMRMOVQ, IPOPQ, IRET };
## Set write control signal
bool mem_write = M_icode in { IRMMOVQ, IPUSHQ, ICALL };
#/* $begin pipe-m_stat-hcl */
## Update the status
word m_stat = [
dmem_error : SADR;
1 : M_stat;
];
#/* $end pipe-m_stat-hcl */
## Set E port register ID
word w_dstE = W_dstE;
## Set E port value
word w_valE = W_valE;
## Set M port register ID
word w_dstM = W_dstM;
## Set M port value
word w_valM = W_valM;
## Update processor status
word Stat = [
W_stat == SBUB : SAOK;
1 : W_stat;
];
################ Pipeline Register Control #########################
# Should I stall or inject a bubble into Pipeline Register F?
# At most one of these can be true.
bool F_bubble = 0;
bool F_stall =
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOPQ } &&
E_dstM in { d_srcA, d_srcB } ||
# Stalling at fetch while ret passes through pipeline
IRET in { D_icode, E_icode, M_icode };
# Should I stall or inject a bubble into Pipeline Register D?
# At most one of these can be true.
bool D_stall =
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOPQ } &&
E_dstM in { d_srcA, d_srcB };
bool D_bubble =
# Mispredicted branch: backward taken error or forward not-taken error
(
(E_icode == IJXX && E_ifun != UNCOND && E_valC < E_valA && !e_Cnd) ||
(E_icode == IJXX && E_ifun != UNCOND && E_valC >= E_valA && e_Cnd)
) ||
# BBTFNT: This condition will change
# Stalling at fetch while ret passes through pipeline
# but not condition for a load/use hazard
!(E_icode in { IMRMOVQ, IPOPQ } && E_dstM in { d_srcA, d_srcB }) &&
IRET in { D_icode, E_icode, M_icode };
# Should I stall or inject a bubble into Pipeline Register E?
# At most one of these can be true.
bool E_stall = 0;
bool E_bubble =
# Mispredicted branch: backward taken error or forward not-taken error
(
(E_icode == IJXX && E_ifun != UNCOND && E_valC < E_valA && !e_Cnd) ||
(E_icode == IJXX && E_ifun != UNCOND && E_valC >= E_valA && e_Cnd)
) ||
# BBTFNT: This condition will change
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOPQ } &&
E_dstM in { d_srcA, d_srcB};
# Should I stall or inject a bubble into Pipeline Register M?
# At most one of these can be true.
bool M_stall = 0;
# Start injecting bubbles as soon as exception passes through memory stage
bool M_bubble = m_stat in { SADR, SINS, SHLT } || W_stat in { SADR, SINS, SHLT };
# Should I stall or inject a bubble into Pipeline Register W?
bool W_stall = W_stat in { SADR, SINS, SHLT };
bool W_bubble = 0;
#/* $end pipe-all-hcl */
模拟器测试结果截图(ISA Checks Succeed)：
4.58
设计思想：
分析pipe-1w.hcl，需要对f_icode, instr_valid,need_regids, f_predPC, d_srcA, d_srcB, d_dstM, aluA, aluB, mem_addr, mem_read,F_stall, D_stall, D_bubble, E_bubble进行修改。
word f_icode = [
Imem_error : INOP;
1 : imem_icode;
];
修改为：
word f_icode = [
Imem_error : INOP;
D_icode == IPOPQ : IPOP2;
1 : imem_icode;
];
bool instr_valid = f_icode in{…}; 大括号中所列指令需加上IPOP2
bool need_regids = f_icode in{…}; 大括号中所列指令需加上IPOP2
word f_predPC = [
f_icode in { IJXX, ICALL } : f_valC;
1 : f_valP;
];
修改为：
word f_predPC = [
f_icode in { IJXX, ICALL } : f_valC;
f_icode == IPOPQ : f_pc;
1 : f_valP;
];
word d_srcA = [
..
D_icode in { RET } : RRSP; 大括号中所列指令需加上IPOP2
…
];
word d_srcB = [
…
D_icode in { IPUSHQ, IPOPQ, ICALL, IRET } :RRSP;大括号中所列指令需加上IPOP2
…
];
word d_dstM = [
D_icode in { IMRMOVQ, IPOPQ } : D_rA;
1 : RNONE;
];
修改为：
word d_dstM = [
D_icode in { IMRMOVQ, IPOP2 } : D_rA;
1 : RNONE;
];
word aluA = [
…
E_icode in { ICALL, IPUSHQ } : -8 大括号中所列指令需加上IPOP2
…
];
word aluB = [
…
E_icode in { … } : E_valB; 大括号中所列指令需加上IPOP2
…
];
word mem_addr = [
M_icode in { IRMMOVQ, IPUSHQ, ICALL,IMRMOVQ } : M_valE;
M_icode in { IPOPQ, IRET } : M_valA;
];
修改为：
word mem_addr = [
M_icode in { IRMMOVQ, IPUSHQ, ICALL,IMRMOVQ, IPOP2} : M_valE;
M_icode in { IRET } : M_valA;
];
bool mem_read = M_icode in { IMRMOVQ,IPOPQ, IRET };
修改为：bool mem_read = M_icode in {IMRMOVQ, IPOP2, IRET };
bool F_stall =
E_icode in { IMRMOVQ, IPOPQ } &&E_dstM in { d_srcA, d_srcB } || IRET in { D_icode, E_icode, M_icode };
修改为：
bool F_stall =
E_icode in { IMRMOVQ, IPOP2 } &&E_dstM in { d_srcA, d_srcB } || IRET in { D_icode, E_icode, M_icode };
bool D_stall =
E_icode in { IMRMOVQ, IPOPQ } &&E_dstM in { d_srcA, d_srcB };
修改为：
bool D_stall =
E_icode in { IMRMOVQ, IPOP2 } &&E_dstM in { d_srcA, d_srcB };
bool D_bubble = …中IPOPQ换为IPOP2。
boolE_bubble = …中IPOPQ换为POP2。修改后pipe-1w.hcl文件：
#/* $begin pipe-all-hcl */
####################################################################
# HCL Description of Control for Pipelined Y86-64 Processor #
# Copyright (C) Randal E. Bryant, David R. O'Hallaron, 2014 #
####################################################################
## Your task is to modify the design so that on any cycle, only
## one of the two possible (valE and valM) register writes will occur.
## This requires special handling of the popq instruction.
## Overall strategy: IPOPQ passes through pipe,
## treated as stack pointer increment, but not incrementing the PC
## On refetch, modify fetched icode to indicate an instruction "IPOP2",
## which reads from memory.
## This requires modifying the definition of f_icode
## and lots of other changes. Relevant positions to change
## are indicated by comments starting with keyword "1W".
####################################################################
# C Include's. Don't alter these #
####################################################################
quote '#include <stdio.h>'
quote '#include "isa.h"'
quote '#include "pipeline.h"'
quote '#include "stages.h"'
quote '#include "sim.h"'
quote 'int sim_main(int argc, char *argv[]);'
quote 'int main(int argc, char *argv[]){return sim_main(argc,argv);}'
####################################################################
# Declarations. Do not change/remove/delete any of these #
####################################################################
##### Symbolic representation of Y86-64 Instruction Codes #############
wordsig INOP 'I_NOP'
wordsig IHALT 'I_HALT'
wordsig IRRMOVQ 'I_RRMOVQ'
wordsig IIRMOVQ 'I_IRMOVQ'
wordsig IRMMOVQ 'I_RMMOVQ'
wordsig IMRMOVQ 'I_MRMOVQ'
wordsig IOPQ 'I_ALU'
wordsig IJXX 'I_JMP'
wordsig ICALL 'I_CALL'
wordsig IRET 'I_RET'
wordsig IPUSHQ 'I_PUSHQ'
wordsig IPOPQ 'I_POPQ'
# 1W: Special instruction code for second try of popq
wordsig IPOP2 'I_POP2'
##### Symbolic represenations of Y86-64 function codes #####
wordsig FNONE 'F_NONE' # Default function code
##### Symbolic representation of Y86-64 Registers referenced #####
wordsig RRSP 'REG_RSP' # Stack Pointer
wordsig RNONE 'REG_NONE' # Special value indicating "no register"
##### ALU Functions referenced explicitly ##########################
wordsig ALUADD 'A_ADD' # ALU should add its arguments
##### Possible instruction status values #####
wordsig SBUB 'STAT_BUB' # Bubble in stage
wordsig SAOK 'STAT_AOK' # Normal execution
wordsig SADR 'STAT_ADR' # Invalid memory address
wordsig SINS 'STAT_INS' # Invalid instruction
wordsig SHLT 'STAT_HLT' # Halt instruction encountered
##### Signals that can be referenced by control logic ##############
##### Pipeline Register F ##########################################
wordsig F_predPC 'pc_curr->pc' # Predicted value of PC
##### Intermediate Values in Fetch Stage ###########################
wordsig imem_icode 'imem_icode' # icode field from instruction memory
wordsig imem_ifun 'imem_ifun' # ifun field from instruction memory
wordsig f_icode 'if_id_next->icode' # (Possibly modified) instruction code
wordsig f_ifun 'if_id_next->ifun' # Fetched instruction function
wordsig f_valC 'if_id_next->valc' # Constant data of fetched instruction
wordsig f_valP 'if_id_next->valp' # Address of following instruction
## 1W: Provide access to the PC value for the current instruction
wordsig f_pc 'f_pc' # Address of fetched instruction
boolsig imem_error 'imem_error' # Error signal from instruction memory
boolsig instr_valid 'instr_valid' # Is fetched instruction valid?
##### Pipeline Register D ##########################################
wordsig D_icode 'if_id_curr->icode' # Instruction code
wordsig D_rA 'if_id_curr->ra' # rA field from instruction
wordsig D_rB 'if_id_curr->rb' # rB field from instruction
wordsig D_valP 'if_id_curr->valp' # Incremented PC
##### Intermediate Values in Decode Stage #########################
wordsig d_srcA 'id_ex_next->srca' # srcA from decoded instruction
wordsig d_srcB 'id_ex_next->srcb' # srcB from decoded instruction
wordsig d_rvalA 'd_regvala' # valA read from register file
wordsig d_rvalB 'd_regvalb' # valB read from register file
##### Pipeline Register E ##########################################
wordsig E_icode 'id_ex_curr->icode' # Instruction code
wordsig E_ifun 'id_ex_curr->ifun' # Instruction function
wordsig E_valC 'id_ex_curr->valc' # Constant data
wordsig E_srcA 'id_ex_curr->srca' # Source A register ID
wordsig E_valA 'id_ex_curr->vala' # Source A value
wordsig E_srcB 'id_ex_curr->srcb' # Source B register ID
wordsig E_valB 'id_ex_curr->valb' # Source B value
wordsig E_dstE 'id_ex_curr->deste' # Destination E register ID
wordsig E_dstM 'id_ex_curr->destm' # Destination M register ID
##### Intermediate Values in Execute Stage #########################
wordsig e_valE 'ex_mem_next->vale' # valE generated by ALU
boolsig e_Cnd 'ex_mem_next->takebranch' # Does condition hold?
wordsig e_dstE 'ex_mem_next->deste' # dstE (possibly modified to be RNONE)
##### Pipeline Register M #########################
wordsig M_stat 'ex_mem_curr->status' # Instruction status
wordsig M_icode 'ex_mem_curr->icode' # Instruction code
wordsig M_ifun 'ex_mem_curr->ifun' # Instruction function
wordsig M_valA 'ex_mem_curr->vala' # Source A value
wordsig M_dstE 'ex_mem_curr->deste' # Destination E register ID
wordsig M_valE 'ex_mem_curr->vale' # ALU E value
wordsig M_dstM 'ex_mem_curr->destm' # Destination M register ID
boolsig M_Cnd 'ex_mem_curr->takebranch' # Condition flag
boolsig dmem_error 'dmem_error' # Error signal from instruction memory
##### Intermediate Values in Memory Stage ##########################
wordsig m_valM 'mem_wb_next->valm' # valM generated by memory
wordsig m_stat 'mem_wb_next->status' # stat (possibly modified to be SADR)
##### Pipeline Register W ##########################################
wordsig W_stat 'mem_wb_curr->status' # Instruction status
wordsig W_icode 'mem_wb_curr->icode' # Instruction code
wordsig W_dstE 'mem_wb_curr->deste' # Destination E register ID
wordsig W_valE 'mem_wb_curr->vale' # ALU E value
wordsig W_dstM 'mem_wb_curr->destm' # Destination M register ID
wordsig W_valM 'mem_wb_curr->valm' # Memory M value
####################################################################
# Control Signal Definitions. #
####################################################################
################ Fetch Stage ###################################
## What address should instruction be fetched at
word f_pc = [
# Mispredicted branch. Fetch at incremented PC
M_icode == IJXX && !M_Cnd : M_valA;
# Completion of RET instruction
W_icode == IRET : W_valM;
# Default: Use predicted value of PC
1 : F_predPC;
];
## Determine icode of fetched instruction
## 1W: To split ipopq into two cycles, need to be able to
## modify value of icode,
## so that it will be IPOP2 when fetched for second time.
word f_icode = [
imem_error : INOP;
D_icode == IPOPQ : IPOP2;
1: imem_icode;
];
# Determine ifun
word f_ifun = [
imem_error : FNONE;
1: imem_ifun;
];
# Is instruction valid?
bool instr_valid = f_icode in
{ INOP, IHALT, IRRMOVQ, IIRMOVQ, IRMMOVQ, IMRMOVQ,
IOPQ, IJXX, ICALL, IRET, IPUSHQ, IPOPQ, IPOP2 };
# Determine status code for fetched instruction
word f_stat = [
imem_error: SADR;
!instr_valid : SINS;
f_icode == IHALT : SHLT;
1 : SAOK;
];
# Does fetched instruction require a regid byte?
bool need_regids =
f_icode in { IRRMOVQ, IOPQ, IPUSHQ, IPOPQ,
IIRMOVQ, IRMMOVQ, IMRMOVQ, IPOP2 };
# Does fetched instruction require a constant word?
bool need_valC =
f_icode in { IIRMOVQ, IRMMOVQ, IMRMOVQ, IJXX, ICALL };
# Predict next value of PC
word f_predPC = [
f_icode in { IJXX, ICALL } : f_valC;
## 1W: Want to refetch popq one time
f_icode == IPOPQ : f_pc;
1 : f_valP;
];
################ Decode Stage ######################################
## W1: Strategy. Decoding of popq rA should be treated the same
## as would iaddq $8, %rsp
## Decoding of pop2 rA treated same as mrmovq -8(%rsp), rA
## What register should be used as the A source?
word d_srcA = [
D_icode in { IRRMOVQ, IRMMOVQ, IOPQ, IPUSHQ } : D_rA;
D_icode in { IRET } : RRSP;
1 : RNONE; # Don't need register
];
## What register should be used as the B source?
word d_srcB = [
D_icode in { IOPQ, IRMMOVQ, IMRMOVQ } : D_rB;
D_icode in { IPUSHQ, IPOPQ, ICALL, IRET, IPOP2 } : RRSP;
1 : RNONE; # Don't need register
];
## What register should be used as the E destination?
word d_dstE = [
D_icode in { IRRMOVQ, IIRMOVQ, IOPQ} : D_rB;
D_icode in { IPUSHQ, IPOPQ, ICALL, IRET } : RRSP;
1 : RNONE; # Don't write any register
];
## What register should be used as the M destination?
word d_dstM = [
D_icode in { IMRMOVQ, IPOP2 } : D_rA;
1 : RNONE; # Don't write any register
];
## What should be the A value?
## Forward into decode stage for valA
word d_valA = [
D_icode in { ICALL, IJXX } : D_valP; # Use incremented PC
d_srcA == e_dstE : e_valE; # Forward valE from execute
d_srcA == M_dstM : m_valM; # Forward valM from memory
d_srcA == M_dstE : M_valE; # Forward valE from memory
d_srcA == W_dstM : W_valM; # Forward valM from write back
d_srcA == W_dstE : W_valE; # Forward valE from write back
1 : d_rvalA; # Use value read from register file
];
word d_valB = [
d_srcB == e_dstE : e_valE; # Forward valE from execute
d_srcB == M_dstM : m_valM; # Forward valM from memory
d_srcB == M_dstE : M_valE; # Forward valE from memory
d_srcB == W_dstM : W_valM; # Forward valM from write back
d_srcB == W_dstE : W_valE; # Forward valE from write back
1 : d_rvalB; # Use value read from register file
];
################ Execute Stage #####################################
## Select input A to ALU
word aluA = [
E_icode in { IRRMOVQ, IOPQ } : E_valA;
E_icode in { IIRMOVQ, IRMMOVQ, IMRMOVQ } : E_valC;
E_icode in { ICALL, IPUSHQ, IPOP2 } : -8;
E_icode in { IRET, IPOPQ } : 8;
# Other instructions don't need ALU
];
## Select input B to ALU
word aluB = [
E_icode in { IRMMOVQ, IMRMOVQ, IOPQ, ICALL,
IPUSHQ, IRET, IPOPQ, IPOP2 } : E_valB;
E_icode in { IRRMOVQ, IIRMOVQ } : 0;
# Other instructions don't need ALU
];
## Set the ALU function
word alufun = [
E_icode == IOPQ : E_ifun;
1 : ALUADD;
];
## Should the condition codes be updated?
bool set_cc = E_icode == IOPQ &&
# State changes only during normal operation
!m_stat in { SADR, SINS, SHLT } && !W_stat in { SADR, SINS, SHLT };
## Generate valA in execute stage
word e_valA = E_valA; # Pass valA through stage
## Set dstE to RNONE in event of not-taken conditional move
word e_dstE = [
E_icode == IRRMOVQ && !e_Cnd : RNONE;
1 : E_dstE;
];
################ Memory Stage ######################################
## Select memory address
word mem_addr = [
M_icode in { IRMMOVQ, IPUSHQ, ICALL, IMRMOVQ, IPOP2 } : M_valE;
M_icode in { IRET } : M_valA;
# Other instructions don't need address
];
## Set read control signal
bool mem_read = M_icode in { IMRMOVQ, IPOP2, IRET };
## Set write control signal
bool mem_write = M_icode in { IRMMOVQ, IPUSHQ, ICALL };
#/* $begin pipe-m_stat-hcl */
## Update the status
word m_stat = [
dmem_error : SADR;
1 : M_stat;
];
#/* $end pipe-m_stat-hcl */
################ Write back stage ##################################
## 1W: For this problem, we introduce a multiplexor that merges
## valE and valM into a single value for writing to register port E.
## DO NOT CHANGE THIS LOGIC
## Merge both write back sources onto register port E
## Set E port register ID
word w_dstE = [
## writing from valM
W_dstM != RNONE : W_dstM;
1: W_dstE;
];
## Set E port value
word w_valE = [
W_dstM != RNONE : W_valM;
1: W_valE;
];
## Disable register port M
## Set M port register ID
word w_dstM = RNONE;
## Set M port value
word w_valM = 0;
## Update processor status
word Stat = [
W_stat == SBUB : SAOK;
1 : W_stat;
];
################ Pipeline Register Control #########################
# Should I stall or inject a bubble into Pipeline Register F?
# At most one of these can be true.
bool F_bubble = 0;
bool F_stall =
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOP2 } &&
E_dstM in { d_srcA, d_srcB } ||
# Stalling at fetch while ret passes through pipeline
IRET in { D_icode, E_icode, M_icode };
# Should I stall or inject a bubble into Pipeline Register D?
# At most one of these can be true.
bool D_stall =
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOP2 } &&
E_dstM in { d_srcA, d_srcB };
bool D_bubble =
# Mispredicted branch
(E_icode == IJXX && !e_Cnd) ||
# Stalling at fetch while ret passes through pipeline
# but not condition for a load/use hazard
!(E_icode in { IMRMOVQ, IPOP2 } && E_dstM in { d_srcA, d_srcB }) &&
# 1W: This condition will change
IRET in { D_icode, E_icode, M_icode };
# Should I stall or inject a bubble into Pipeline Register E?
# At most one of these can be true.
bool E_stall = 0;
bool E_bubble =
# Mispredicted branch
(E_icode == IJXX && !e_Cnd) ||
# Conditions for a load/use hazard
E_icode in { IMRMOVQ, IPOP2 } &&
E_dstM in { d_srcA, d_srcB};
# Should I stall or inject a bubble into Pipeline Register M?
# At most one of these can be true.
bool M_stall = 0;
# Start injecting bubbles as soon as exception passes through memory stage
bool M_bubble = m_stat in { SADR, SINS, SHLT } || W_stat in { SADR, SINS, SHLT };
# Should I stall or inject a bubble into Pipeline Register W?
bool W_stall = W_stat in { SADR, SINS, SHLT };
bool W_bubble = 0;
#/* $end pipe-all-hcl */
模拟器测试结果截图(ISA Checks Succeed)：
