链路捆绑、单臂、静态、默认路由配置
实验目标
运用vlan、链路捆绑、单臂、静态和默认路由实现下图全网通
实验步骤
1.二层交换机让各个VLAN下电脑互通
2.三层交换机和单臂路由配置ip地址
3.配置三层交换机和路由的静态、默认下跳点
SW1二层交换机配置
[SW1]vlan batch 10 20 ##创建vlan 10 20
[SW1]int g0/0/1 ##进入g0/0/1接口
[SW1-GigabitEthernet0/0/1]port link-type trunk ##trunk链路
[SW1-GigabitEthernet0/0/1]port trunk allow-pass vlan all ##允许全部vlan通过
[SW1-GigabitEthernet0/0/1]undo shutdown ##激活端口
[SW1]int g0/0/2
[SW1-GigabitEthernet0/0/2]port link-type trunk
[SW1-GigabitEthernet0/0/2]port trunk allow-pass vlan all
[SW1-GigabitEthernet0/0/2]undo shutdown
[SW1-GigabitEthernet0/0/2]int e0/0/1
[SW1-Ethernet0/0/1]port link-type access
[SW1-Ethernet0/0/1]port default vlan 10 ##划分到vlan10
[SW1-Ethernet0/0/1]undo shutdown
[SW1-Ethernet0/0/1]int e0/0/2
[SW1-Ethernet0/0/2]port link-type access
[SW1-Ethernet0/0/2]port default vlan 20 ##划分到vlan20
[SW1-Ethernet0/0/2]undo shutdown
SW2二层交换机配置
[SW2]vlan batch 10 20
[SW2]int g0/0/1
[SW2-GigabitEthernet0/0/1]port link-type trunk
[SW2-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[SW2-GigabitEthernet0/0/1]undo shutdown
[SW2-GigabitEthernet0/0/1]int e0/0/1
[SW2-Ethernet0/0/1]port link-type access ##access链路
[SW2-Ethernet0/0/1]port default vlan 10
[SW2-Ethernet0/0/1]undo shutdown
[SW2-Ethernet0/0/1]int e0/0/2
[SW2-Ethernet0/0/2]port link-type access
[SW2-Ethernet0/0/2]port default vlan 20
[SW2-Ethernet0/0/2]undo shutdown
SW3二层交换机配置
[SW3]vlan batch 30 40
[SW3]int e0/0/1
[SW3-Ethernet0/0/1]port link-type access
[SW3-Ethernet0/0/1]port default vlan 30
[SW3-Ethernet0/0/1]undo shutdown
[SW3-Ethernet0/0/1]int e0/0/2
[SW3-Ethernet0/0/2]port link-type access
[SW3-Ethernet0/0/2]port default vlan 40
[SW3-Ethernet0/0/2]undo shutdown
[SW3]int Eth-Trunk1 ##进入捆绑链路1
[SW3-Eth-Trunk1]port link-type trunk
[SW3-Eth-Trunk1]port trunk allow-pass vlan all
[SW3-Eth-Trunk1]undo shutdown
[SW3-Eth-Trunk1]trunkport g 0/0/1 to 0/0/2 ##把g0/0/1到g0/0/2加入捆绑链路1
RSW4三层交换机配置
[RSW1]vlan batch 10 20 30
[RSW1]int g0/0/2
[RSW1-GigabitEthernet0/0/2]port link-type trunk
[RSW1-GigabitEthernet0/0/2]port trunk allow-pass vlan 10 20
[RSW1]int g0/0/3
[RSW1-GigabitEthernet0/0/3]port link-type access
[RSW1-GigabitEthernet0/0/3]port default vlan 30
[RSW1-GigabitEthernet0/0/3]undo shutdown
[RSW1]int Vlanif 10 ##进入vlanif配置
[RSW1-Vlanif10]ip address 192.168.10.1 24 ##配置vlanif配置网关子网掩码
[RSW1-Vlanif10]undo shutdown
[RSW1]int Vlanif 20
[RSW1-Vlanif20]ip add 192.168.20.1 24
[RSW1-Vlanif20]undo shutdown
[RSW1]interface Vlanif 30
[RSW1-Vlanif30]ip add 12.0.0.1 30
[RSW1-Vlanif30]undo shutdown
R1路由器配置
[R1]int g0/0/3
[R1-GigabitEthernet0/0/3]ip add 12.0.0.2 30
[R1]int Eth-Trunk1
[R1-Eth-Trunk1]trunkport g 0/0/1 to 0/0/2
[R1]int Eth-Trunk1.30 ##进入子接口
[R1-Eth-Trunk1.30]dot1q termination vid 30 ##把vlan30加入子接口
[R1-Eth-Trunk1.30]ip add 192.168.30.1 24 ##配置子接口网关子网掩码
[R1-Eth-Trunk1.30]arp broadcast enable ##开启ARP广播
[R1]int Eth-Trunk1.40
[R1-Eth-Trunk1.40]dot1q termination vid 40
[R1-Eth-Trunk1.40]ip add 192.168.40.1 24
[R1-Eth-Trunk1.40]arp broadcast enable
RSW4三层交换机和R1路由器静态、默认补全
[RSW1]ip route-static 0.0.0.0 0.0.0.0 12.0.0.2 ##向上指默认路由
[R1]ip route-static 192.168.10.0 24 12.0.0.1 ##向下指静态路由
[R1]ip route-static 192.168.20.0 24 12.0.0.1
6台PC配置ip
如果有错误的地方，欢迎评论，我加以改正。