Cisco switch basic configuration commands
switch>enable 进入特权模式
switch#config terminal 进入全局模式
switch(config)#hostname+xxx 设置主机名
switch(config)#enable password 明文密码
switch(config)#enable secret 密文密码
switch(config)#ip default-gateway 设置网关
switch#show mac-address-table 查看MAC地址
switch(config)#logging synchronous 阻止控制台信息覆盖命令行上的输入
switch(config)#no ip domain-lookup 关闭DNS查看功能
switch(config)#exec-timeout 0 0 阻止会话退出
Remote management using telnet
switch(config)#line vty 0 4 进入虚拟终端
switch(config-line)#password xx 设置登录口令
switch(config-line)#login 要求口令验证
console password
switch(config)#line console 0 进入控制台口
switch(config-line)#password xx
switch(config-line)# 设置登录口令login 允许登录
cisco discovery protocol (cdp)
switch(config)#show cdp 显示cisco设备全局配置信息
switch(config)#show cdp interface端口 查看cdp配置下端口信息
switch(config)#show cdp neighbors 显示直连cisco设备信息
switch(config)#show cdp neighbors detail 查看邻居详细信息
Cisco switch restore factory configuration
switch#erase startup-config
switch#delete flash: vlan.dat
Configure interface identification (distinguish each interface of the router)
switch(config)#interface fastethernet0/1
switch(config)#description this is a fast ethernet port used to connecting the company's intranet!
vtp configuration
switch(config)#vtp domain 设置VTP域名
switch(config)#vtp password xx 设置VTP密码
switch(config)#vtp mode server/client/transparent 设置VTP服务模式
switch(config)#vtp version 设置VTP版本
switch(config)#vtp pruning 设置VTP修解
vlan basic configuration
switch#vlan database 进入vlan配置模式
switch(vlan)#vlan 号码 name 名称 创建vlan及vlan名
switch(vlan)#vlan 号码 mtu 数值 修改MTU大小
switch(vlan)#exit 更新vlan数据并退出
switch#show vlan 查看vlan
switch#copy running-config startup-config 保存配置
Add and delete ports in vlan
switch#conf t
switch(config)#interface fastethernet0/1 进入要分配的端口
switch(config-if)#switchport mode access 定义二层端口
switch(config-if)#switchport access vlan号码 把端口发给一个vlan
switch(config-if)#switchport mode trunk 设置为干线
switch(config-if)#switchport trunk encapsulation dotlq 设置vlan中继协议
switch(config-if)#no switchport mode 或 (switchport mode access) 禁用干线
switch(config-if)#switchport trunk allowed vlan add 1,2 从trunk中添加vlans
switch(config-if)#switchport trunk allowed vlan remove1,2 从trunk中删除vlan
switch(config-if)#switchport trunk pruning vlan remove1,2
Configure the interface to be in dynamic negotiation mode
switch(config)#interface 接口号
switch(config)#switchport mode dynamic desirable/auto
spanning tree stp
switch(config)#spanning-tree vlan 启用stp生成树(基于vlan)
switch(config)#spanning-tree vlan root primary 指定交换机(基于vlan)
switch(config)#spanning-tree vlan root secondary 指定备用根交换机(基于vlan)
switch(config)#spanning-tree vlan priority<0-65535> 指定交换机优先继(基于vlan)
switch(config)#no spanning-tree vlan priority 将交换机的优先级恢复默认值(基于vlan)
switch(config-if)#spanning-tree vlan cost<0-200000000> 指定端口成本(起用trunk的端口模式下)
switch(config-if)#spanning-tree vlan port-prioty<0-255> 指定交换机端口优先级(基于vlan)
switch(config-if)#spanning-tree portfast 配置速端口(连接终端设备的端口状态)如pc机
switch(config)#spanning-tree uplinkfast 配置上行速端口
- Note: Before configuring the uplink speed port, you must first restore the default value of the bridge priority and bridge cost based on the VLAN. Priority changes are made after this command is enabled.
- Note: vlan is an optional parameter. If there is no such parameter, the priority of all vlan bridges\and all vlan port costs will be modified
switch#show spanning-tree summery 检测vlan生成树配置
switch#show spanning-tree vlan detail 浏览详细生成树配置信息
switch#show spanning-tree interface detail 浏览详细生成树端口配置信息
Ethernet channel configuration
switch(config)#interface range fastemet0/1-2 将fastemet0/1和0/2口捆绑
switch(config-if)#change-group 1 mode on 配置以太通道模式
switch(config-if)#port-channel load-batance{dst-mac|src-mac}在链路间实现负载均衡
switch#show etherchannel 1 summary 查看通道信息
switch#show etherchannel load-balance 查看通道信息
switch show command
switch#show vtp status 查看vtp配置信息
switch#show running-config 查看当前配置信息
switch#show vlan 查看vlan配置信息
switch#show interface 查看端口信息
switch#show int f0/0 查看指定端口信息
switch#dir flash: 查看闪存
switch#show version 查看当前版本信息
switch#show cdp cisco 设备发现协议(可以查看聆接设备)
switch#show cdp traffic 查看接收和发送的cdp包统计信息
switch#show interface f0/1 switchport 查看有关switchport的配置
switch#show cdp neighbors 查看与该设备相邻的cisco设备
CISCO switch inspection command
1、show interface stats ;查看交换机所有接口当前接口流量
2、show running-config ;查看当前设备配置
3、show version ;查看IOS版本信息及设备正常运行时间
4、show clock ;查看设备时钟信息
5、show vtp status ;查看交换机vtp配置模式
6、show vtp password ;查看交换机vtp配置口令
7、show env all ;查看设备温度,电源和风扇运转参数及是否报警
8、show inventory ;调取设备内部板卡出厂模块型号及序列号
9、show spanning-tree root ;查看交换机生成树根位置
10、show cdp neighbors ;查看邻接cisco设备基本信息
11、show cdp neighbors detail ;查看邻接cisco设备详细信息
12、show interface status ;查看交换机接口状态是否存在errordisable接口disable接口
13、show interface summary ;查看交换机所有接口当前接口流量
14、show interface | i errors|FastEthernet|GigabitEthernet ;查看接口是否存在大量input或output errors包错误
15、show processes cpu ;查看设备cpu负载
16、show processes mem ;查看设备mem负载
17、show access-list ;查看访问控制列表配置及匹配数据包数量
18、show logging ;查看本机内部日志记录情况
19、show ip route ;查看路由表
20、show firewall ;检查防火墙的工作模式
21、show conn count ;检查防火墙并发数
22、show xlate count ;检查防火墙nat工作状态