stm32驱动1.44寸LCD屏幕显示中文字符包含可移植keil5工程代码

1.44寸LCD屏幕

之前的0.96寸的OLED屏幕坏掉了，现在重新买了一块1.44寸的LCD屏幕，感觉这次的质量比较好，还可以显示彩色的
用的IC是stm32f103vet6

接线方法是
供电要5V的，3.3V只会白屏
SCL接PB13
SDA接PB15
RES接PB12(复位，和stm32接同一个复位就行)
DC接PB10
那个CS片选完全可以不接就默认浮空吧
BL接GND的话是关闭屏幕，浮空或者接3.3V就是开启屏幕，那就不接默认浮空吧
在这里插入图片描述

将某宝卖家提供的工程移植到了自己的工程模板中，简单的使用了一下，明天整理好以后在评论地方放百度网盘的keil5工程

放一个例子显示的效果图
之后准备做个简单的dht11温湿度显示
在这里插入图片描述

这里贴一下lcd代码，会移植的就直接移植就行了
lcd.c

#include "lcd.h"
#include "stdlib.h"
#include "usart.h"
#include "delay.h"	 

/****************************************************************************************************
//=======================================液晶屏数据线接线==========================================//
//CS		接PB11	//片选信号
//CLK	    接PB13	//SPI时钟信号
//SDI(DIN)	接PB15	//SPI总线数据信号
//=======================================液晶屏控制线接线==========================================//
//LED	    接PB9	//背光控制信号，高电平点亮
//RS(D/C)   接PB10	//寄存器/数据选择信号(RS=0数据总线发送的是指令；RS=1数据总线发送的是像素数据)
//RST	    接PB12	//液晶屏复位信号，低电平复位
/////////////////////////////////////////////////////////////////////////////////////////////////
//==================================如何精简到只需要3个IO=======================================//
//1.CS信号可以精简，不作SPI复用片选可将CS接地常低，节省1个IO
//2.LED背光控制信号可以接高电平3.3V背光常亮，节省1个IO
//3.RST复位信号可以接到单片机的复位端，利用系统上电复位，节省1个IO
//==================================如何切换横竖屏显示=======================================//
//打开lcd.h头文件，修改宏#define USE_HORIZONTAL 值为0使用竖屏模式.1,使用横屏模式
//===========================如何切换模拟SPI总线驱动和硬件SPI总线驱动=========================//
//打开lcd.h头文件，修改宏#define USE_HARDWARE_SPI  值为0使用模拟SPI总线.1,使用硬件SPI总线
**************************************************************************************************/	

	   
//管理LCD重要参数
//默认为竖屏
_lcd_dev lcddev;

//画笔颜色,背景颜色
u16 POINT_COLOR = 0x0000,BACK_COLOR = 0xFFFF;  
u16 DeviceCode;	 

/****************************************************************************
* 名    称：void  SPIv_WriteData(u8 Data)
* 功    能：STM32_模拟SPI写一个字节数据底层函数
* 入口参数：Data
* 出口参数：无
* 说    明：STM32_模拟SPI读写一个字节数据底层函数
****************************************************************************/
void  SPIv_WriteData(u8 Data)
{
	unsigned char i=0;
	for(i=8;i>0;i--)
	{
		if(Data&0x80)	
	  LCD_SDA_SET; //输出数据
      else LCD_SDA_CLR;
	   
      LCD_SCL_CLR;       
      LCD_SCL_SET;
      Data<<=1; 
	}
}

/****************************************************************************
* 名    称：u8 SPI_WriteByte(SPI_TypeDef* SPIx,u8 Byte)
* 功    能：STM32_硬件SPI读写一个字节数据底层函数
* 入口参数：SPIx,Byte
* 出口参数：返回总线收到的数据
* 说    明：STM32_硬件SPI读写一个字节数据底层函数
****************************************************************************/
u8 SPI_WriteByte(SPI_TypeDef* SPIx,u8 Byte)
{
	while((SPIx->SR&SPI_I2S_FLAG_TXE)==RESET);		//等待发送区空	  
	SPIx->DR=Byte;	 	//发送一个byte   
	while((SPIx->SR&SPI_I2S_FLAG_RXNE)==RESET);//等待接收完一个byte  
	return SPIx->DR;          	     //返回收到的数据			
} 

/****************************************************************************
* 名    称：void SPI_SetSpeed(SPI_TypeDef* SPIx,u8 SpeedSet)
* 功    能：设置SPI的速度
* 入口参数：SPIx,SpeedSet
* 出口参数：无
* 说    明：SpeedSet:1,高速;0,低速;
****************************************************************************/
void SPI_SetSpeed(SPI_TypeDef* SPIx,u8 SpeedSet)
{
	SPIx->CR1&=0XFFC7;
	if(SpeedSet==1)//高速
	{
		SPIx->CR1|=SPI_BaudRatePrescaler_2;//Fsck=Fpclk/2	
	}
	else//低速
	{
		SPIx->CR1|=SPI_BaudRatePrescaler_32; //Fsck=Fpclk/32
	}
	SPIx->CR1|=1<<6; //SPI设备使能
} 

/****************************************************************************
* 名    称：SPI2_Init(void)
* 功    能：STM32_SPI2硬件配置初始化
* 入口参数：无
* 出口参数：无
* 说    明：STM32_SPI2硬件配置初始化
****************************************************************************/
void SPI2_Init(void)	
{
	SPI_InitTypeDef  SPI_InitStructure;
	GPIO_InitTypeDef GPIO_InitStructure;
	 
	//配置SPI2管脚
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO|RCC_APB2Periph_GPIOB, ENABLE);
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13 | GPIO_Pin_15;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
	GPIO_Init(GPIOB, &GPIO_InitStructure);

	GPIO_InitStructure.GPIO_Pin =  GPIO_Pin_14;    
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU; 
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;  
	GPIO_Init(GPIOB, &GPIO_InitStructure);  

	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9|GPIO_Pin_10| GPIO_Pin_11| GPIO_Pin_12;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
	GPIO_Init(GPIOB, &GPIO_InitStructure);
	
	//SPI2配置选项
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2 ,ENABLE);
	   
	SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
	SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
	SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
	SPI_InitStructure.SPI_CPOL = SPI_CPOL_High;
	SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;
	SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
	SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2;
	SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
	SPI_InitStructure.SPI_CRCPolynomial = 7;
	SPI_Init(SPI2, &SPI_InitStructure);

	//使能SPI2
	SPI_Cmd(SPI2, ENABLE);   
}

//******************************************************************
//功能：    向液晶屏总线写入写16位指令
//******************************************************************
void LCD_WR_REG(u16 data)
{ 
   LCD_CS_CLR;
   LCD_RS_CLR;
#if USE_HARDWARE_SPI   
   SPI_WriteByte(SPI2,data);
#else
   SPIv_WriteData(data);
#endif 
   LCD_CS_SET;
}

//******************************************************************
//功能：    向液晶屏总线写入写8位数据
//******************************************************************
void LCD_WR_DATA(u8 data)
{
	
   LCD_CS_CLR;
   LCD_RS_SET;
#if USE_HARDWARE_SPI   
   SPI_WriteByte(SPI2,data);
#else
   SPIv_WriteData(data);
#endif 
   LCD_CS_SET;

}
//******************************************************************
//功能：    8位总线下如何写入一个16位数据
//******************************************************************
void LCD_WR_DATA_16Bit(u16 data)
{	
   LCD_CS_CLR;
   LCD_RS_SET;
#if USE_HARDWARE_SPI   
   SPI_WriteByte(SPI2,data>>8);
   SPI_WriteByte(SPI2,data);
#else
   SPIv_WriteData(data>>8);
   SPIv_WriteData(data);
#endif 
   LCD_CS_SET;
}

//******************************************************************
//功能：    写寄存器数据
//******************************************************************
void LCD_WriteReg(u16 LCD_Reg, u16 LCD_RegValue)
{	
	LCD_WR_REG(LCD_Reg);  
	LCD_WR_DATA(LCD_RegValue);	    		 
}	   
	 
//******************************************************************
//开始写GRAM
//在给液晶屏传送RGB数据前，应该发送写GRAM指令
//******************************************************************
void LCD_WriteRAM_Prepare(void)
{
	LCD_WR_REG(lcddev.wramcmd);
}	 

//******************************************************************
//在指定位置写入一个像素点数据
//******************************************************************
void LCD_DrawPoint(u16 x,u16 y)
{
	LCD_SetCursor(x,y);//设置光标位置 
	LCD_WR_DATA_16Bit(POINT_COLOR);
}

//******************************************************************
//液晶屏IO初始化，液晶初始化前要调用此函数
//******************************************************************
void LCD_GPIOInit(void)
{
	GPIO_InitTypeDef  GPIO_InitStructure;
	      
	RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOB ,ENABLE);
	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9| GPIO_Pin_10| GPIO_Pin_11| GPIO_Pin_12 | GPIO_Pin_13 | GPIO_Pin_14| GPIO_Pin_15;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
	GPIO_Init(GPIOB, &GPIO_InitStructure);      
}

//******************************************************************
//功能：    LCD复位函数，液晶初始化前要调用此函数
//******************************************************************
void LCD_RESET(void)
{
	LCD_RST_CLR;
	delay_ms(100);	
	LCD_RST_SET;
	delay_ms(50);
}
 	 
//******************************************************************
//LCD初始化
//******************************************************************
void LCD_Init(void)
{  
#if USE_HARDWARE_SPI //使用硬件SPI
	SPI2_Init();
#else	
	LCD_GPIOInit();//使用模拟SPI
#endif  										 

 	LCD_RESET(); //液晶屏复位

	//************* Start Initial Sequence **********//		
	//开始初始化液晶屏
	LCD_WR_REG(0x11);//Sleep exit 
	delay_ms (120);		
	//ST7735R Frame Rate
	LCD_WR_REG(0xB1); 
	LCD_WR_DATA(0x01); 
	LCD_WR_DATA(0x2C); 
	LCD_WR_DATA(0x2D); 

	LCD_WR_REG(0xB2); 
	LCD_WR_DATA(0x01); 
	LCD_WR_DATA(0x2C); 
	LCD_WR_DATA(0x2D); 

	LCD_WR_REG(0xB3); 
	LCD_WR_DATA(0x01); 
	LCD_WR_DATA(0x2C); 
	LCD_WR_DATA(0x2D); 
	LCD_WR_DATA(0x01); 
	LCD_WR_DATA(0x2C); 
	LCD_WR_DATA(0x2D); 
	
	LCD_WR_REG(0xB4); //Column inversion 
	LCD_WR_DATA(0x07); 
	
	//ST7735R Power Sequence
	LCD_WR_REG(0xC0); 
	LCD_WR_DATA(0xA2); 
	LCD_WR_DATA(0x02); 
	LCD_WR_DATA(0x84); 
	LCD_WR_REG(0xC1); 
	LCD_WR_DATA(0xC5); 

	LCD_WR_REG(0xC2); 
	LCD_WR_DATA(0x0A); 
	LCD_WR_DATA(0x00); 

	LCD_WR_REG(0xC3); 
	LCD_WR_DATA(0x8A); 
	LCD_WR_DATA(0x2A); 
	LCD_WR_REG(0xC4); 
	LCD_WR_DATA(0x8A); 
	LCD_WR_DATA(0xEE); 
	
	LCD_WR_REG(0xC5); //VCOM 
	LCD_WR_DATA(0x0E); 
	
	LCD_WR_REG(0x36); //MX, MY, RGB mode 				 
	LCD_WR_DATA(0xC8); 
	
	//ST7735R Gamma Sequence
	LCD_WR_REG(0xe0); 
	LCD_WR_DATA(0x0f); 
	LCD_WR_DATA(0x1a); 
	LCD_WR_DATA(0x0f); 
	LCD_WR_DATA(0x18); 
	LCD_WR_DATA(0x2f); 
	LCD_WR_DATA(0x28); 
	LCD_WR_DATA(0x20); 
	LCD_WR_DATA(0x22); 
	LCD_WR_DATA(0x1f); 
	LCD_WR_DATA(0x1b); 
	LCD_WR_DATA(0x23); 
	LCD_WR_DATA(0x37); 
	LCD_WR_DATA(0x00); 	
	LCD_WR_DATA(0x07); 
	LCD_WR_DATA(0x02); 
	LCD_WR_DATA(0x10); 

	LCD_WR_REG(0xe1); 
	LCD_WR_DATA(0x0f); 
	LCD_WR_DATA(0x1b); 
	LCD_WR_DATA(0x0f); 
	LCD_WR_DATA(0x17); 
	LCD_WR_DATA(0x33); 
	LCD_WR_DATA(0x2c); 
	LCD_WR_DATA(0x29); 
	LCD_WR_DATA(0x2e); 
	LCD_WR_DATA(0x30); 
	LCD_WR_DATA(0x30); 
	LCD_WR_DATA(0x39); 
	LCD_WR_DATA(0x3f); 
	LCD_WR_DATA(0x00); 
	LCD_WR_DATA(0x07); 
	LCD_WR_DATA(0x03); 
	LCD_WR_DATA(0x10);  
	
	LCD_WR_REG(0x2a);
	LCD_WR_DATA(0x00);
	LCD_WR_DATA(0x00);
	LCD_WR_DATA(0x00);
	LCD_WR_DATA(0x7f);

	LCD_WR_REG(0x2b);
	LCD_WR_DATA(0x00);
	LCD_WR_DATA(0x00);
	LCD_WR_DATA(0x00);
	LCD_WR_DATA(0x9f);
	
	LCD_WR_REG(0xF0); //Enable test command  
	LCD_WR_DATA(0x01); 
	LCD_WR_REG(0xF6); //Disable ram power save mode 
	LCD_WR_DATA(0x00); 
	
	LCD_WR_REG(0x3A); //65k mode 
	LCD_WR_DATA(0x05); 	
	LCD_WR_REG(0x29);//Display on	

	LCD_SetParam();//设置LCD参数	 
	LCD_LED_SET;//点亮背光	 
	//LCD_Clear(WHITE);
}
//******************************************************************
//LCD全屏填充清屏函数
//******************************************************************
void LCD_Clear(u16 Color)
{
	u16 i,j;      
	LCD_SetWindows(0,0,lcddev.width-1,lcddev.height-1);	  
	for(i=0;i<lcddev.width;i++)
	{
		for(j=0;j<lcddev.height;j++)
		LCD_WR_DATA_16Bit(Color);	//写入数据 	 
	}
}  
 		  
/*************************************************
功能：设置lcd显示窗口，在此区域写点数据自动换行
入口参数：xy起点和终点
*************************************************/
void LCD_SetWindows(u16 xStar, u16 yStar,u16 xEnd,u16 yEnd)
{
#if USE_HORIZONTAL==1	//使用横屏
	LCD_WR_REG(lcddev.setxcmd);	
	LCD_WR_DATA(xStar>>8);
	LCD_WR_DATA(0x00FF&xStar+3);		
	LCD_WR_DATA(xEnd>>8);
	LCD_WR_DATA(0x00FF&xEnd+3);

	LCD_WR_REG(lcddev.setycmd);	
	LCD_WR_DATA(yStar>>8);
	LCD_WR_DATA(0x00FF&yStar+2);		
	LCD_WR_DATA(yEnd>>8);
	LCD_WR_DATA(0x00FF&yEnd+2);	

#else
	
	LCD_WR_REG(lcddev.setxcmd);	
	LCD_WR_DATA(xStar>>8);
	LCD_WR_DATA(0x00FF&xStar+2);		
	LCD_WR_DATA(xEnd>>8);
	LCD_WR_DATA(0x00FF&xEnd+2);

	LCD_WR_REG(lcddev.setycmd);	
	LCD_WR_DATA(yStar>>8);
	LCD_WR_DATA(0x00FF&yStar+3);		
	LCD_WR_DATA(yEnd>>8);
	LCD_WR_DATA(0x00FF&yEnd+3);	
#endif

	LCD_WriteRAM_Prepare();	//开始写入GRAM				
}   

/*************************************************
功能：设置光标位置
入口参数：xy坐标
*************************************************/
void LCD_SetCursor(u16 Xpos, u16 Ypos)
{	  	    			
	LCD_SetWindows(Xpos,Ypos,Xpos,Ypos);
} 

//设置LCD参数
//方便进行横竖屏模式切换
void LCD_SetParam(void)
{ 	
	lcddev.wramcmd=0x2C;
#if USE_HORIZONTAL==1	//使用横屏	  
	lcddev.dir=1;//横屏
	lcddev.width=128;
	lcddev.height=128;
	lcddev.setxcmd=0x2A;
	lcddev.setycmd=0x2B;			
	LCD_WriteReg(0x36,0xA8);

#else//竖屏
	lcddev.dir=0;//竖屏				 	 		
	lcddev.width=128;
	lcddev.height=128;
	lcddev.setxcmd=0x2A;
	lcddev.setycmd=0x2B;	
	LCD_WriteReg(0x36,0xC8);
#endif
}

lcd.h

#ifndef __LCD_H
#define __LCD_H		
#include "sys.h"	 
#include "stdlib.h"


//LCD重要参数集
typedef struct  
{										    
	u16 width;			//LCD 宽度
	u16 height;			//LCD 高度
	u16 id;				//LCD ID
	u8  dir;			//横屏还是竖屏控制：0，竖屏；1，横屏。	
	u16	 wramcmd;		//开始写gram指令
	u16  setxcmd;		//设置x坐标指令
	u16  setycmd;		//设置y坐标指令	 
}_lcd_dev; 	

//LCD参数
extern _lcd_dev lcddev;	//管理LCD重要参数
/////////////////////////////////////用户配置区///////////////////////////////////	 
//支持横竖屏快速定义切换，支持8/16位模式切换
#define USE_HORIZONTAL  	0	//定义是否使用横屏 		0,不使用.1,使用.
//使用硬件SPI 还是模拟SPI作为测试
#define USE_HARDWARE_SPI    1  //1:Enable Hardware SPI;0:USE Soft SPI
//////////////////////////////////////////////////////////////////////////////////	  
//定义LCD的尺寸
#if USE_HORIZONTAL==1	//使用横屏
#define LCD_W 320
#define LCD_H 240
#else
#define LCD_W 240
#define LCD_H 320
#endif

//TFTLCD部分外要调用的函数		   
extern u16  POINT_COLOR;//默认红色    
extern u16  BACK_COLOR; //背景颜色.默认为白色

////////////////////////////////////////////////////////////////////
//-----------------LCD端口定义---------------- 
//QDtech全系列模块采用了三极管控制背光亮灭，用户也可以接PWM调节背光亮度
#define LCD_LED        	GPIO_Pin_9  //PB9 连接至TFT -LED
//接口定义在Lcd_Driver.h内定义，请根据接线修改并修改相应IO初始化LCD_GPIO_Init()
#define LCD_CTRL   	  	GPIOB		//定义TFT数据端口
#define LCD_RS         	GPIO_Pin_10	//PB10连接至TFT --RS
#define LCD_CS        	GPIO_Pin_11 //PB11 连接至TFT --CS
#define LCD_RST     	GPIO_Pin_12	//PB12连接至TFT --RST
#define LCD_SCL        	GPIO_Pin_13	//PB13连接至TFT -- CLK
#define LCD_SDA        	GPIO_Pin_15	//PB15连接至TFT - SDI
							    
//////////////////////////////////////////////////////////////////////
//液晶控制口置1操作语句宏定义
#define	LCD_CS_SET  	LCD_CTRL->BSRR=LCD_CS    
#define	LCD_RS_SET  	LCD_CTRL->BSRR=LCD_RS    
#define	LCD_SDA_SET  	LCD_CTRL->BSRR=LCD_SDA    
#define	LCD_SCL_SET  	LCD_CTRL->BSRR=LCD_SCL    
#define	LCD_RST_SET  	LCD_CTRL->BSRR=LCD_RST    
#define	LCD_LED_SET  	LCD_CTRL->BSRR=LCD_LED   

//液晶控制口置0操作语句宏定义
#define	LCD_CS_CLR  	LCD_CTRL->BRR=LCD_CS    
#define	LCD_RS_CLR  	LCD_CTRL->BRR=LCD_RS    
#define	LCD_SDA_CLR  	LCD_CTRL->BRR=LCD_SDA    
#define	LCD_SCL_CLR  	LCD_CTRL->BRR=LCD_SCL    
#define	LCD_RST_CLR  	LCD_CTRL->BRR=LCD_RST    
#define	LCD_LED_CLR  	LCD_CTRL->BRR=LCD_LED 

//画笔颜色
#define WHITE       0xFFFF
#define BLACK      	0x0000	  
#define BLUE       	0x001F  
#define BRED        0XF81F
#define GRED 			 	0XFFE0
#define GBLUE			 	0X07FF
#define RED         0xF800
#define MAGENTA     0xF81F
#define GREEN       0x07E0
#define CYAN        0x7FFF
#define YELLOW      0xFFE0
#define BROWN 			0XBC40 //棕色
#define BRRED 			0XFC07 //棕红色
#define GRAY  			0X8430 //灰色
//GUI颜色

#define DARKBLUE      	 0X01CF	//深蓝色
#define LIGHTBLUE      	 0X7D7C	//浅蓝色  
#define GRAYBLUE       	 0X5458 //灰蓝色
//以上三色为PANEL的颜色 
 
#define LIGHTGREEN     	0X841F //浅绿色
//#define LIGHTGRAY     0XEF5B //浅灰色(PANNEL)
#define LGRAY 			 		0XC618 //浅灰色(PANNEL),窗体背景色

#define LGRAYBLUE      	0XA651 //浅灰蓝色(中间层颜色)
#define LBBLUE          0X2B12 //浅棕蓝色(选择条目的反色)
	    															  
extern u16 BACK_COLOR, POINT_COLOR ;  

void LCD_Init(void);
void LCD_DisplayOn(void);
void LCD_DisplayOff(void);
void LCD_Clear(u16 Color);	 
void LCD_SetCursor(u16 Xpos, u16 Ypos);
void LCD_DrawPoint(u16 x,u16 y);//画点
u16  LCD_ReadPoint(u16 x,u16 y); //读点
void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2);
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2);		   
void LCD_SetWindows(u16 xStar, u16 yStar,u16 xEnd,u16 yEnd);
void LCD_DrawPoint_16Bit(u16 color);
u16 LCD_RD_DATA(void);//读取LCD数据									    
void LCD_WriteReg(u16 LCD_Reg, u16 LCD_RegValue);
void LCD_WR_DATA(u8 data);
void LCD_WR_DATA_16Bit(u16 data);
u16 LCD_ReadReg(u8 LCD_Reg);
void LCD_WriteRAM_Prepare(void);
void LCD_WriteRAM(u16 RGB_Code);
u16 LCD_ReadRAM(void);		   
u16 LCD_BGR2RGB(u16 c);
void LCD_SetParam(void);

						  		 
#endif

gui.c

#include "lcd.h"
#include "string.h"
#include "font.h" 
#include "delay.h"
#include "gui.h"

//******************************************************************
//函数名：  GUI_DrawPoint
//作者：    xiao冯@全动电子
//日期：    2013-02-22
//功能：    GUI描绘一个点
//输入参数：x:光标位置x坐标
//        	y:光标位置y坐标
//			color:要填充的颜色
//返回值：  无
//修改记录：无
//******************************************************************
void GUI_DrawPoint(u16 x,u16 y,u16 color)
{
	LCD_SetCursor(x,y);//设置光标位置 
	LCD_WR_DATA_16Bit(color); 
}

//******************************************************************
//功能：    在指定区域内填充颜色
//输入参数：sx:指定区域开始点x坐标
//        	sy:指定区域开始点y坐标
//			ex:指定区域结束点x坐标
//			ey:指定区域结束点y坐标
//        	color:要填充的颜色
//******************************************************************
void LCD_Fill(u16 sx,u16 sy,u16 ex,u16 ey,u16 color)
{  	

	u16 i,j;			
	u16 width=ex-sx+1; 		//得到填充的宽度
	u16 height=ey-sy+1;		//高度
	LCD_SetWindows(sx,sy,ex-1,ey-1);//设置显示窗口
	for(i=0;i<height;i++)
	{
		for(j=0;j<width;j++)
		LCD_WR_DATA_16Bit(color);	//写入数据 	 
	}

	LCD_SetWindows(0,0,lcddev.width-1,lcddev.height-1);//恢复窗口设置为全屏
}

//******************************************************************
//功能：    GUI画线
//输入参数：x1,y1:起点坐标
//        	x2,y2:终点坐标 
//****************************************************************** 
void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2)
{
	u16 t; 
	int xerr=0,yerr=0,delta_x,delta_y,distance; 
	int incx,incy,uRow,uCol; 

	delta_x=x2-x1; //计算坐标增量 
	delta_y=y2-y1; 
	uRow=x1; 
	uCol=y1; 
	if(delta_x>0)incx=1; //设置单步方向 
	else if(delta_x==0)incx=0;//垂直线 
	else {incx=-1;delta_x=-delta_x;} 
	if(delta_y>0)incy=1; 
	else if(delta_y==0)incy=0;//水平线 
	else{incy=-1;delta_y=-delta_y;} 
	if( delta_x>delta_y)distance=delta_x; //选取基本增量坐标轴 
	else distance=delta_y; 
	for(t=0;t<=distance+1;t++ )//画线输出 
	{  
		LCD_DrawPoint(uRow,uCol);//画点 
		xerr+=delta_x ; 
		yerr+=delta_y ; 
		if(xerr>distance) 
		{ 
			xerr-=distance; 
			uRow+=incx; 
		} 
		if(yerr>distance) 
		{ 
			yerr-=distance; 
			uCol+=incy; 
		} 
	}  
} 

//******************************************************************
//功能：    GUI画矩形(非填充)
//输入参数：(x1,y1),(x2,y2):矩形的对角坐标
//******************************************************************  
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2)
{
	LCD_DrawLine(x1,y1,x2,y1);
	LCD_DrawLine(x1,y1,x1,y2);
	LCD_DrawLine(x1,y2,x2,y2);
	LCD_DrawLine(x2,y1,x2,y2);
}  

//******************************************************************
//功能：    GUI画矩形(填充)
//输入参数：(x1,y1),(x2,y2):矩形的对角坐标
//******************************************************************   
void LCD_DrawFillRectangle(u16 x1, u16 y1, u16 x2, u16 y2)
{
	LCD_Fill(x1,y1,x2,y2,POINT_COLOR);

}
 
//******************************************************************
//功能：    8对称性画圆算法(内部调用)
//输入参数：(xc,yc) :圆中心坐标
// 			(x,y):光标相对于圆心的坐标
//         	c:填充的颜色
//******************************************************************  
void _draw_circle_8(int xc, int yc, int x, int y, u16 c)
{
	GUI_DrawPoint(xc + x, yc + y, c);

	GUI_DrawPoint(xc - x, yc + y, c);

	GUI_DrawPoint(xc + x, yc - y, c);

	GUI_DrawPoint(xc - x, yc - y, c);

	GUI_DrawPoint(xc + y, yc + x, c);

	GUI_DrawPoint(xc - y, yc + x, c);

	GUI_DrawPoint(xc + y, yc - x, c);

	GUI_DrawPoint(xc - y, yc - x, c);
}

//******************************************************************
//功能：    在指定位置画一个指定大小的圆(填充)
//输入参数：(xc,yc) :圆中心坐标
//         	c:填充的颜色
//		 	r:圆半径
//		 	fill:填充判断标志，1-填充，0-不填充
//******************************************************************  
void gui_circle(int xc, int yc,u16 c,int r, int fill)
{
	int x = 0, y = r, yi, d;

	d = 3 - 2 * r;


	if (fill) 
	{
		// 如果填充（画实心圆）
		while (x <= y) {
			for (yi = x; yi <= y; yi++)
				_draw_circle_8(xc, yc, x, yi, c);

			if (d < 0) {
				d = d + 4 * x + 6;
			} else {
				d = d + 4 * (x - y) + 10;
				y--;
			}
			x++;
		}
	} else 
	{
		// 如果不填充（画空心圆）
		while (x <= y) {
			_draw_circle_8(xc, yc, x, y, c);
			if (d < 0) {
				d = d + 4 * x + 6;
			} else {
				d = d + 4 * (x - y) + 10;
				y--;
			}
			x++;
		}
	}
}

//******************************************************************
//功能：    显示单个英文字符
//输入参数：(x,y):字符显示位置起始坐标
//        	fc:前置画笔颜色
//			bc:背景颜色
//			num:数值（0-94）
//			size:字体大小
//			mode:模式  0,填充模式;1,叠加模式
//******************************************************************  
void LCD_ShowChar(u16 x,u16 y,u16 fc, u16 bc, u8 num,u8 size,u8 mode)
{  
    u8 temp;
    u8 pos,t;
	u16 colortemp=POINT_COLOR;      
		   
	num=num-' ';//得到偏移后的值
	LCD_SetWindows(x,y,x+size/2-1,y+size-1);//设置单个文字显示窗口
	if(!mode) //非叠加方式
	{
		
		for(pos=0;pos<size;pos++)
		{
			if(size==12)temp=asc2_1206[num][pos];//调用1206字体
			else temp=asc2_1608[num][pos];		 //调用1608字体
			for(t=0;t<size/2;t++)
		    {                 
		        if(temp&0x01)LCD_WR_DATA(fc); 
				else LCD_WR_DATA(bc); 
				temp>>=1; 
				
		    }
			
		}	
	}else//叠加方式
	{
		for(pos=0;pos<size;pos++)
		{
			if(size==12)temp=asc2_1206[num][pos];//调用1206字体
			else temp=asc2_1608[num][pos];		 //调用1608字体
			for(t=0;t<size/2;t++)
		    {   
				POINT_COLOR=fc;              
		        if(temp&0x01)LCD_DrawPoint(x+t,y+pos);//画一个点    
		        temp>>=1; 
		    }
		}
	}
	POINT_COLOR=colortemp;	
	LCD_SetWindows(0,0,lcddev.width-1,lcddev.height-1);//恢复窗口为全屏    	   	 	  
} 

//******************************************************************
//功能：    显示单个英文字符
//输入参数：(x,y):字符显示位置起始坐标
//        	fc:前置画笔颜色
//			bc:背景颜色
//			num:数值（0-94）
//			size:字体大小
//			mode:模式  0,填充模式;1,叠加模式
//******************************************************************  
void LCD_ShowNum2412(u16 x,u16 y,u16 fc, u16 bc,u8 *p ,u8 size,u8 mode)
{  
    u16 temp;
    u8 pos,t;
	u16 colortemp=POINT_COLOR;      
	u16 x0=x;
	u16 y0=y; 
	u8 num=0;
	

    while((*p<='~')&&(*p>=' '))//判断是不是非法字符!
    {   

		if(x>(lcddev.width-1)||y>(lcddev.height-1)) 
		return;   
		num=*p;
		if(':'==num) //特殊字符":"
		num=10;	
		else if('.'==num)//特殊字符"."
		num=11;	
		else  //纯数字   	
		num=num-'0';   
		x0=x;
		    
		for(pos=0;pos<48;pos++)
		{
			temp=asc2_2412[num][pos];
			for(t=0;t<8;t++)
		    {   
				POINT_COLOR=fc;              
		        if(temp&0x80)LCD_DrawPoint(x,y);//画一个点  
				//else LCD_WR_DATA_16Bit(bc);   
		        temp<<=1; 
				x++;
				if((x-x0)==12)
				{
					x=x0;
					y++;
					break;
				}
		    }
		}
	if(num<10)
	x+=16;	//人为控制字距，使得排版更好看，原值为12
	else
	x+=8; //人为控制字距，使得排版更好看，原值为12

	y=y0;
    p++;
    }  
	POINT_COLOR=colortemp;	 	 	  
} 


//******************************************************************
//功能：    显示英文字符串
//输入参数：x,y :起点坐标	 
//			size:字体大小
//			*p:字符串起始地址
//			mode:模式	0,填充模式;1,叠加模式
//******************************************************************  	  
void LCD_ShowString(u16 x,u16 y,u8 size,u8 *p,u8 mode)
{         
    while((*p<='~')&&(*p>=' '))//判断是不是非法字符!
    {   
		if(x>(lcddev.width-1)||y>(lcddev.height-1)) 
		return;     
        LCD_ShowChar(x,y,POINT_COLOR,BACK_COLOR,*p,size,mode);
        x+=size/2;
        p++;
    }  
} 

//******************************************************************
//功能：    求m的n次方(gui内部调用)
//输入参数：m:乘数
//	        n:幂
//返回值：  m的n次方
//******************************************************************  
u32 mypow(u8 m,u8 n)
{
	u32 result=1;	 
	while(n--)result*=m;    
	return result;
}

//******************************************************************
//功能：    显示单个数字变量值
//输入参数：x,y :起点坐标	 
//			len :指定显示数字的位数
//			size:字体大小(12,16)
//			color:颜色
//			num:数值(0~4294967295)
//******************************************************************  			 
void LCD_ShowNum(u16 x,u16 y,u32 num,u8 len,u8 size)
{         	
	u8 t,temp;
	u8 enshow=0;						   
	for(t=0;t<len;t++)
	{
		temp=(num/mypow(10,len-t-1))%10;
		if(enshow==0&&t<(len-1))
		{
			if(temp==0)
			{
				LCD_ShowChar(x+(size/2)*t,y,POINT_COLOR,BACK_COLOR,' ',size,1);
				continue;
			}else enshow=1; 
		 	 
		}
	 	LCD_ShowChar(x+(size/2)*t,y,POINT_COLOR,BACK_COLOR,temp+'0',size,1); 
	}
} 

//******************************************************************
//功能：    显示单个16X16中文字体
//输入参数：x,y :起点坐标
//			fc:前置画笔颜色
//			bc:背景颜色	 
//			s:字符串地址
//			mode:模式	0,填充模式;1,叠加模式
//******************************************************************
void GUI_DrawFont16(u16 x, u16 y, u16 fc, u16 bc, u8 *s,u8 mode)
{
	u8 i,j;
	u16 k;
	u16 HZnum;
	u16 x0=x;
	HZnum=sizeof(tfont16)/sizeof(typFNT_GB16);	//自动统计汉字数目
	
			
	for (k=0;k<HZnum;k++) 
	{
	  if ((tfont16[k].Index[0]==*(s))&&(tfont16[k].Index[1]==*(s+1)))
	  { 	LCD_SetWindows(x,y,x+16-1,y+16-1);
		    for(i=0;i<16*2;i++)
		    {
				for(j=0;j<8;j++)
		    	{	
					if(!mode) //非叠加方式
					{
						if(tfont16[k].Msk[i]&(0x80>>j))	LCD_WR_DATA_16Bit(fc);
						else LCD_WR_DATA_16Bit(bc);
					}
					else
					{
						POINT_COLOR=fc;
						if(tfont16[k].Msk[i]&(0x80>>j))	LCD_DrawPoint(x,y);//画一个点
						x++;
						if((x-x0)==16)
						{
							x=x0;
							y++;
							break;
						}
					}

				}
				
			}
			
			
		}				  	
		continue;  //查找到对应点阵字库立即退出，防止多个汉字重复取模带来影响
	}

	LCD_SetWindows(0,0,lcddev.width-1,lcddev.height-1);//恢复窗口为全屏  
} 

//******************************************************************
//功能：    显示单个24X24中文字体
//输入参数：x,y :起点坐标
//			fc:前置画笔颜色
//			bc:背景颜色	 
//			s:字符串地址
//			mode:模式	0,填充模式;1,叠加模式
//******************************************************************
void GUI_DrawFont24(u16 x, u16 y, u16 fc, u16 bc, u8 *s,u8 mode)
{
	u8 i,j;
	u16 k;
	u16 HZnum;
	u16 x0=x;
	HZnum=sizeof(tfont24)/sizeof(typFNT_GB24);	//自动统计汉字数目
		
			for (k=0;k<HZnum;k++) 
			{
			  if ((tfont24[k].Index[0]==*(s))&&(tfont24[k].Index[1]==*(s+1)))
			  { 	LCD_SetWindows(x,y,x+24-1,y+24-1);
				    for(i=0;i<24*3;i++)
				    {
							for(j=0;j<8;j++)
							{
								if(!mode) //非叠加方式
								{
									if(tfont24[k].Msk[i]&(0x80>>j))	LCD_WR_DATA_16Bit(fc);
									else LCD_WR_DATA_16Bit(bc);
								}
							else
							{
								POINT_COLOR=fc;
								if(tfont24[k].Msk[i]&(0x80>>j))	LCD_DrawPoint(x,y);//画一个点
								x++;
								if((x-x0)==24)
								{
									x=x0;
									y++;
									break;
								}
							}
						}
					}
					
					
				}				  	
				continue;  //查找到对应点阵字库立即退出，防止多个汉字重复取模带来影响
			}

	LCD_SetWindows(0,0,lcddev.width-1,lcddev.height-1);//恢复窗口为全屏  
}

//******************************************************************
//功能：    显示单个32X32中文字体
//输入参数：x,y :起点坐标
//			fc:前置画笔颜色
//			bc:背景颜色	 
//			s:字符串地址
//			mode:模式	0,填充模式;1,叠加模式
//****************************************************************** 
void GUI_DrawFont32(u16 x, u16 y, u16 fc, u16 bc, u8 *s,u8 mode)
{
	u8 i,j;
	u16 k;
	u16 HZnum;
	u16 x0=x;
	HZnum=sizeof(tfont32)/sizeof(typFNT_GB32);	//自动统计汉字数目
	for (k=0;k<HZnum;k++) 
			{
			  if ((tfont32[k].Index[0]==*(s))&&(tfont32[k].Index[1]==*(s+1)))
			  { 	LCD_SetWindows(x,y,x+32-1,y+32-1);
				    for(i=0;i<32*4;i++)
				    {
						for(j=0;j<8;j++)
				    	{
							if(!mode) //非叠加方式
							{
								if(tfont32[k].Msk[i]&(0x80>>j))	LCD_WR_DATA_16Bit(fc);
								else LCD_WR_DATA_16Bit(bc);
							}
							else
							{
								POINT_COLOR=fc;
								if(tfont32[k].Msk[i]&(0x80>>j))	LCD_DrawPoint(x,y);//画一个点
								x++;
								if((x-x0)==32)
								{
									x=x0;
									y++;
									break;
								}
							}
						}
					}
					
					
				}				  	
				continue;  //查找到对应点阵字库立即退出，防止多个汉字重复取模带来影响
			}
	
	LCD_SetWindows(0,0,lcddev.width-1,lcddev.height-1);//恢复窗口为全屏  
} 

//******************************************************************
//功能：    显示一个字符串,包含中英文显示
//输入参数：x,y :起点坐标
// 			fc:前置画笔颜色
//			bc:背景颜色
//			str :字符串	 
//			size:字体大小
//			mode:模式	0,填充模式;1,叠加模式
//******************************************************************    	   		   
void Show_Str(u16 x, u16 y, u16 fc, u16 bc, u8 *str,u8 size,u8 mode)
{					
	u16 x0=x;							  	  
  	u8 bHz=0;     //字符或者中文 
    while(*str!=0)//数据未结束
    { 
        if(!bHz)
        {
			if(x>(lcddev.width-size/2)||y>(lcddev.height-size)) 
			return; 
	        if(*str>0x80)bHz=1;//中文 
	        else              //字符
	        {          
		        if(*str==0x0D)//换行符号
		        {         
		            y+=size;
					x=x0;
		            str++; 
		        }  
		        else
				{
					if(size==12||size==16)
					{  
					LCD_ShowChar(x,y,fc,bc,*str,size,mode);
					x+=size/2; //字符,为全字的一半 
					}
					else//字库中没有集成16X32的英文字体,用8X16代替
					{
					 	LCD_ShowChar(x,y,fc,bc,*str,16,mode);
						x+=8; //字符,为全字的一半 
					}
				} 
				str++; 
		        
	        }
        }else//中文 
        {   
			if(x>(lcddev.width-size)||y>(lcddev.height-size)) 
			return;  
            bHz=0;//有汉字库    
			if(size==32)
			GUI_DrawFont32(x,y,fc,bc,str,mode);	 	
			else if(size==24)
			GUI_DrawFont24(x,y,fc,bc,str,mode);	
			else
			GUI_DrawFont16(x,y,fc,bc,str,mode);
				
	        str+=2; 
	        x+=size;//下一个汉字偏移	    
        }						 
    }   
}

//******************************************************************
//功能：    居中显示一个字符串,包含中英文显示
//输入参数：x,y :起点坐标
// 			fc:前置画笔颜色
//			bc:背景颜色
//			str :字符串	 
//			size:字体大小
//			mode:模式	0,填充模式;1,叠加模式
//******************************************************************   
void Gui_StrCenter(u16 x, u16 y, u16 fc, u16 bc, u8 *str,u8 size,u8 mode)
{
	u16 len=strlen((const char *)str);
	u16 x1=(lcddev.width-len*8)/2;
	Show_Str(x+x1,y,fc,bc,str,size,mode);
} 
 
//******************************************************************
//功能：    显示一副16位BMP图像
//输入参数：x,y :起点坐标
// 			*p :图像数组起始地址
//******************************************************************  
void Gui_Drawbmp16(u16 x,u16 y,const unsigned char *p) //显示40*40 QQ图片
{
  	int i; 
	unsigned char picH,picL; 
	LCD_SetWindows(x,y,x+40-1,y+40-1);//窗口设置
    for(i=0;i<40*40;i++)
	{	
	 	picL=*(p+i*2);	//数据低位在前
		picH=*(p+i*2+1);				
		LCD_WR_DATA_16Bit(picH<<8|picL);  						
	}	
	LCD_SetWindows(0,0,lcddev.width-1,lcddev.height-1);//恢复显示窗口为全屏	

}

gui.h

#ifndef __GUI_H__
#define __GUI_H__

void GUI_DrawPoint(u16 x,u16 y,u16 color);
void LCD_Fill(u16 sx,u16 sy,u16 ex,u16 ey,u16 color);
void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2);
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2);
void Draw_Circle(u16 x0,u16 y0,u16 fc,u8 r);
void LCD_ShowChar(u16 x,u16 y,u16 fc, u16 bc, u8 num,u8 size,u8 mode);
void LCD_ShowNum(u16 x,u16 y,u32 num,u8 len,u8 size);
void LCD_Show2Num(u16 x,u16 y,u16 num,u8 len,u8 size,u8 mode);
void LCD_ShowString(u16 x,u16 y,u8 size,u8 *p,u8 mode);
void GUI_DrawFont16(u16 x, u16 y, u16 fc, u16 bc, u8 *s,u8 mode);
void GUI_DrawFont24(u16 x, u16 y, u16 fc, u16 bc, u8 *s,u8 mode);
void GUI_DrawFont32(u16 x, u16 y, u16 fc, u16 bc, u8 *s,u8 mode);
void Show_Str(u16 x, u16 y, u16 fc, u16 bc, u8 *str,u8 size,u8 mode);
void Gui_Drawbmp16(u16 x,u16 y,const unsigned char *p); //显示40*40 QQ图片
void gui_circle(int xc, int yc,u16 c,int r, int fill);
void Gui_StrCenter(u16 x, u16 y, u16 fc, u16 bc, u8 *str,u8 size,u8 mode);
void LCD_DrawFillRectangle(u16 x1, u16 y1, u16 x2, u16 y2);
void LCD_ShowNum2412(u16 x,u16 y,u16 fc, u16 bc,u8 *p ,u8 size,u8 mode);
#endif

font.h

#ifndef __FONT_H
#define __FONT_H 	   
//常用ASCII表
//偏移量32
//ASCII字符集
//偏移量32
//大小:12*6
const unsigned char asc2_1206[95][12]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x00,0x04,0x00,0x00},/*"!",1*/
{0x00,0x14,0x0A,0x0A,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x14,0x14,0x3F,0x14,0x0A,0x3F,0x0A,0x0A,0x00,0x00},/*"#",3*/
{0x00,0x04,0x1E,0x15,0x05,0x06,0x0C,0x14,0x15,0x0F,0x04,0x00},/*"$",4*/
{0x00,0x00,0x12,0x15,0x0D,0x0A,0x14,0x2C,0x2A,0x12,0x00,0x00},/*"%",5*/
{0x00,0x00,0x04,0x0A,0x0A,0x1E,0x15,0x15,0x09,0x36,0x00,0x00},/*"&",6*/
{0x00,0x02,0x02,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x20,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x10,0x20,0x00},/*"(",8*/
{0x00,0x02,0x04,0x08,0x08,0x08,0x08,0x08,0x08,0x04,0x02,0x00},/*")",9*/
{0x00,0x00,0x00,0x04,0x15,0x0E,0x0E,0x15,0x04,0x00,0x00,0x00},/*"*",10*/
{0x00,0x00,0x04,0x04,0x04,0x1F,0x04,0x04,0x04,0x00,0x00,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x02,0x01},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x1F,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00},/*".",14*/
{0x00,0x10,0x08,0x08,0x08,0x04,0x04,0x02,0x02,0x02,0x01,0x00},/*"/",15*/
{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x11,0x11,0x0E,0x00,0x00},/*"0",16*/
{0x00,0x00,0x04,0x06,0x04,0x04,0x04,0x04,0x04,0x0E,0x00,0x00},/*"1",17*/
{0x00,0x00,0x0E,0x11,0x11,0x08,0x04,0x02,0x01,0x1F,0x00,0x00},/*"2",18*/
{0x00,0x00,0x0E,0x11,0x10,0x0C,0x10,0x10,0x11,0x0E,0x00,0x00},/*"3",19*/
{0x00,0x00,0x08,0x0C,0x0A,0x0A,0x09,0x1E,0x08,0x18,0x00,0x00},/*"4",20*/
{0x00,0x00,0x1F,0x01,0x01,0x0F,0x10,0x10,0x11,0x0E,0x00,0x00},/*"5",21*/
{0x00,0x00,0x0E,0x09,0x01,0x0F,0x11,0x11,0x11,0x0E,0x00,0x00},/*"6",22*/
{0x00,0x00,0x1F,0x09,0x08,0x04,0x04,0x04,0x04,0x04,0x00,0x00},/*"7",23*/
{0x00,0x00,0x0E,0x11,0x11,0x0E,0x11,0x11,0x11,0x0E,0x00,0x00},/*"8",24*/
{0x00,0x00,0x0E,0x11,0x11,0x11,0x1E,0x10,0x12,0x0E,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x04,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x04,0x00},/*";",27*/
{0x00,0x20,0x10,0x08,0x04,0x02,0x04,0x08,0x10,0x20,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x1F,0x00,0x00,0x1F,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x02,0x04,0x08,0x10,0x20,0x10,0x08,0x04,0x02,0x00,0x00},/*">",30*/
{0x00,0x00,0x0E,0x11,0x11,0x08,0x04,0x04,0x00,0x04,0x00,0x00},/*"?",31*/
{0x00,0x00,0x0E,0x11,0x19,0x15,0x15,0x1D,0x01,0x1E,0x00,0x00},/*"@",32*/
{0x00,0x00,0x04,0x04,0x0C,0x0A,0x0A,0x1E,0x12,0x33,0x00,0x00},/*"A",33*/
{0x00,0x00,0x0F,0x12,0x12,0x0E,0x12,0x12,0x12,0x0F,0x00,0x00},/*"B",34*/
{0x00,0x00,0x1E,0x11,0x01,0x01,0x01,0x01,0x11,0x0E,0x00,0x00},/*"C",35*/
{0x00,0x00,0x0F,0x12,0x12,0x12,0x12,0x12,0x12,0x0F,0x00,0x00},/*"D",36*/
{0x00,0x00,0x1F,0x12,0x0A,0x0E,0x0A,0x02,0x12,0x1F,0x00,0x00},/*"E",37*/
{0x00,0x00,0x1F,0x12,0x0A,0x0E,0x0A,0x02,0x02,0x07,0x00,0x00},/*"F",38*/
{0x00,0x00,0x1C,0x12,0x01,0x01,0x39,0x11,0x12,0x0C,0x00,0x00},/*"G",39*/
{0x00,0x00,0x33,0x12,0x12,0x1E,0x12,0x12,0x12,0x33,0x00,0x00},/*"H",40*/
{0x00,0x00,0x1F,0x04,0x04,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"I",41*/
{0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x09,0x07,0x00},/*"J",42*/
{0x00,0x00,0x37,0x12,0x0A,0x06,0x0A,0x0A,0x12,0x37,0x00,0x00},/*"K",43*/
{0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x22,0x3F,0x00,0x00},/*"L",44*/
{0x00,0x00,0x1B,0x1B,0x1B,0x1B,0x15,0x15,0x15,0x15,0x00,0x00},/*"M",45*/
{0x00,0x00,0x3B,0x12,0x16,0x16,0x1A,0x1A,0x12,0x17,0x00,0x00},/*"N",46*/
{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x11,0x11,0x0E,0x00,0x00},/*"O",47*/
{0x00,0x00,0x0F,0x12,0x12,0x0E,0x02,0x02,0x02,0x07,0x00,0x00},/*"P",48*/
{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x17,0x19,0x0E,0x18,0x00},/*"Q",49*/
{0x00,0x00,0x0F,0x12,0x12,0x0E,0x0A,0x12,0x12,0x37,0x00,0x00},/*"R",50*/
{0x00,0x00,0x1E,0x11,0x01,0x06,0x08,0x10,0x11,0x0F,0x00,0x00},/*"S",51*/
{0x00,0x00,0x1F,0x15,0x04,0x04,0x04,0x04,0x04,0x0E,0x00,0x00},/*"T",52*/
{0x00,0x00,0x33,0x12,0x12,0x12,0x12,0x12,0x12,0x0C,0x00,0x00},/*"U",53*/
{0x00,0x00,0x33,0x12,0x12,0x0A,0x0A,0x0C,0x04,0x04,0x00,0x00},/*"V",54*/
{0x00,0x00,0x15,0x15,0x15,0x0E,0x0A,0x0A,0x0A,0x0A,0x00,0x00},/*"W",55*/
{0x00,0x00,0x1B,0x0A,0x0A,0x04,0x04,0x0A,0x0A,0x1B,0x00,0x00},/*"X",56*/
{0x00,0x00,0x1B,0x0A,0x0A,0x04,0x04,0x04,0x04,0x0E,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x1F,0x09,0x08,0x04,0x04,0x02,0x12,0x1F,0x00,0x00},/*"Z",58*/
{0x00,0x1C,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x1C,0x00},/*"[",59*/
{0x00,0x02,0x02,0x02,0x04,0x04,0x08,0x08,0x08,0x10,0x00,0x00},/*"\",60*/
{0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x0E,0x00},/*"]",61*/
{0x00,0x04,0x0A,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F},/*"_",63*/
{0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x1C,0x12,0x3C,0x00,0x00},/*"a",65*/
{0x00,0x00,0x03,0x02,0x02,0x0E,0x12,0x12,0x12,0x0E,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x00,0x1C,0x12,0x02,0x02,0x1C,0x00,0x00},/*"c",67*/
{0x00,0x00,0x18,0x10,0x10,0x1C,0x12,0x12,0x12,0x3C,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x1E,0x02,0x1C,0x00,0x00},/*"e",69*/
{0x00,0x00,0x38,0x04,0x04,0x1E,0x04,0x04,0x04,0x1E,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x3C,0x12,0x0C,0x02,0x1E,0x22,0x1C},/*"g",71*/
{0x00,0x00,0x03,0x02,0x02,0x0E,0x12,0x12,0x12,0x37,0x00,0x00},/*"h",72*/
{0x00,0x00,0x04,0x00,0x00,0x06,0x04,0x04,0x04,0x0E,0x00,0x00},/*"i",73*/
{0x00,0x00,0x08,0x00,0x00,0x0C,0x08,0x08,0x08,0x08,0x08,0x07},/*"j",74*/
{0x00,0x00,0x03,0x02,0x02,0x3A,0x0A,0x0E,0x12,0x37,0x00,0x00},/*"k",75*/
{0x00,0x00,0x07,0x04,0x04,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"l",76*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0x15,0x15,0x15,0x15,0x00,0x00},/*"m",77*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0x12,0x12,0x12,0x37,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x12,0x12,0x0C,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0x12,0x12,0x12,0x0E,0x02,0x07},/*"p",80*/
{0x00,0x00,0x00,0x00,0x00,0x1C,0x12,0x12,0x12,0x1C,0x10,0x38},/*"q",81*/
{0x00,0x00,0x00,0x00,0x00,0x1B,0x06,0x02,0x02,0x07,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x1E,0x02,0x0C,0x10,0x1E,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x04,0x04,0x0E,0x04,0x04,0x04,0x18,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x00,0x1B,0x12,0x12,0x12,0x3C,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x00,0x37,0x12,0x0A,0x0C,0x04,0x00,0x00},/*"v",86*/
{0x00,0x00,0x00,0x00,0x00,0x15,0x15,0x0E,0x0A,0x0A,0x00,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x00,0x1B,0x0A,0x04,0x0A,0x1B,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x00,0x37,0x12,0x0A,0x0C,0x04,0x04,0x03},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x1E,0x08,0x04,0x04,0x1E,0x00,0x00},/*"z",90*/
{0x00,0x18,0x08,0x08,0x08,0x04,0x08,0x08,0x08,0x08,0x18,0x00},/*"{",91*/
{0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08},/*"|",92*/
{0x00,0x06,0x04,0x04,0x04,0x08,0x04,0x04,0x04,0x04,0x06,0x00},/*"}",93*/
{0x02,0x25,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00} /*"~",94*/
}; 
const unsigned char asc2_1608[95][16]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00,0x18,0x18,0x00,0x00},/*"!",1*/
{0x00,0x48,0x6C,0x24,0x12,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x24,0x24,0x24,0x7F,0x12,0x12,0x12,0x7F,0x12,0x12,0x12,0x00,0x00},/*"#",3*/
{0x00,0x00,0x08,0x1C,0x2A,0x2A,0x0A,0x0C,0x18,0x28,0x28,0x2A,0x2A,0x1C,0x08,0x08},/*"$",4*/
{0x00,0x00,0x00,0x22,0x25,0x15,0x15,0x15,0x2A,0x58,0x54,0x54,0x54,0x22,0x00,0x00},/*"%",5*/
{0x00,0x00,0x00,0x0C,0x12,0x12,0x12,0x0A,0x76,0x25,0x29,0x11,0x91,0x6E,0x00,0x00},/*"&",6*/
{0x00,0x06,0x06,0x04,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x40,0x20,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x10,0x10,0x20,0x40,0x00},/*"(",8*/
{0x00,0x02,0x04,0x08,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x08,0x08,0x04,0x02,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x08,0x08,0x6B,0x1C,0x1C,0x6B,0x08,0x08,0x00,0x00,0x00,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x7F,0x08,0x08,0x08,0x08,0x00,0x00,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x04,0x03},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00},/*".",14*/
{0x00,0x00,0x80,0x40,0x40,0x20,0x20,0x10,0x10,0x08,0x08,0x04,0x04,0x02,0x02,0x00},/*"/",15*/
{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x08,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x20,0x20,0x10,0x08,0x04,0x42,0x7E,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x20,0x18,0x20,0x40,0x40,0x42,0x22,0x1C,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x20,0x30,0x28,0x24,0x24,0x22,0x22,0x7E,0x20,0x20,0x78,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x7E,0x02,0x02,0x02,0x1A,0x26,0x40,0x40,0x42,0x22,0x1C,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x38,0x24,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x7E,0x22,0x22,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00},/*"7",23*/	 
{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x24,0x18,0x24,0x42,0x42,0x42,0x3C,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x64,0x58,0x40,0x40,0x24,0x1C,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x04},/*";",27*/
{0x00,0x00,0x00,0x40,0x20,0x10,0x08,0x04,0x02,0x04,0x08,0x10,0x20,0x40,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x40,0x20,0x10,0x08,0x04,0x02,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x46,0x40,0x20,0x10,0x10,0x00,0x18,0x18,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x1C,0x22,0x5A,0x55,0x55,0x55,0x55,0x2D,0x42,0x22,0x1C,0x00,0x00},/*"@",32*/
{0x00,0x00,0x00,0x08,0x08,0x18,0x14,0x14,0x24,0x3C,0x22,0x42,0x42,0xE7,0x00,0x00},/*"A",33*/
{0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x1E,0x22,0x42,0x42,0x42,0x22,0x1F,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x7C,0x42,0x42,0x01,0x01,0x01,0x01,0x01,0x42,0x22,0x1C,0x00,0x00},/*"C",35*/
{0x00,0x00,0x00,0x1F,0x22,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x22,0x1F,0x00,0x00},/*"D",36*/
{0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x42,0x42,0x3F,0x00,0x00},/*"E",37*/
{0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x02,0x02,0x07,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x3C,0x22,0x22,0x01,0x01,0x01,0x71,0x21,0x22,0x22,0x1C,0x00,0x00},/*"G",39*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x7E,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"H",40*/
{0x00,0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x11,0x0F},/*"J",42*/
{0x00,0x00,0x00,0x77,0x22,0x12,0x0A,0x0E,0x0A,0x12,0x12,0x22,0x22,0x77,0x00,0x00},/*"K",43*/
{0x00,0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x7F,0x00,0x00},/*"L",44*/
{0x00,0x00,0x00,0x77,0x36,0x36,0x36,0x36,0x2A,0x2A,0x2A,0x2A,0x2A,0x6B,0x00,0x00},/*"M",45*/
{0x00,0x00,0x00,0xE3,0x46,0x46,0x4A,0x4A,0x52,0x52,0x52,0x62,0x62,0x47,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x41,0x41,0x22,0x1C,0x00,0x00},/*"O",47*/
{0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x42,0x3E,0x02,0x02,0x02,0x02,0x07,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x4D,0x53,0x32,0x1C,0x60,0x00},/*"Q",49*/
{0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x3E,0x12,0x12,0x22,0x22,0x42,0xC7,0x00,0x00},/*"R",50*/
{0x00,0x00,0x00,0x7C,0x42,0x42,0x02,0x04,0x18,0x20,0x40,0x42,0x42,0x3E,0x00,0x00},/*"S",51*/
{0x00,0x00,0x00,0x7F,0x49,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00},/*"T",52*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00},/*"U",53*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x22,0x24,0x24,0x14,0x14,0x18,0x08,0x08,0x00,0x00},/*"V",54*/
{0x00,0x00,0x00,0x6B,0x49,0x49,0x49,0x49,0x55,0x55,0x36,0x22,0x22,0x22,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x18,0x18,0x18,0x24,0x24,0x42,0xE7,0x00,0x00},/*"X",56*/
{0x00,0x00,0x00,0x77,0x22,0x22,0x14,0x14,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x7E,0x21,0x20,0x10,0x10,0x08,0x04,0x04,0x42,0x42,0x3F,0x00,0x00},/*"Z",58*/
{0x00,0x78,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x78,0x00},/*"[",59*/
{0x00,0x00,0x02,0x02,0x04,0x04,0x08,0x08,0x08,0x10,0x10,0x20,0x20,0x20,0x40,0x40},/*"\",60*/
{0x00,0x1E,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x1E,0x00},/*"]",61*/
{0x00,0x38,0x44,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF},/*"_",63*/
{0x00,0x06,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x78,0x44,0x42,0x42,0xFC,0x00,0x00},/*"a",65*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x26,0x1A,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x44,0x02,0x02,0x02,0x44,0x38,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x60,0x40,0x40,0x40,0x78,0x44,0x42,0x42,0x42,0x64,0xD8,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x7E,0x02,0x02,0x42,0x3C,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0xF0,0x88,0x08,0x08,0x7E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x22,0x22,0x1C,0x02,0x3C,0x42,0x42,0x3C},/*"g",71*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x3A,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"h",72*/
{0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x38,0x20,0x20,0x20,0x20,0x20,0x20,0x22,0x1E},/*"j",74*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x72,0x12,0x0A,0x16,0x12,0x22,0x77,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"l",76*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x92,0x92,0x92,0x92,0x92,0xB7,0x00,0x00},/*"m",77*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3B,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1B,0x26,0x42,0x42,0x42,0x22,0x1E,0x02,0x07},/*"p",80*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x44,0x42,0x42,0x42,0x44,0x78,0x40,0xE0},/*"q",81*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x77,0x4C,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x42,0x02,0x3C,0x40,0x42,0x3E,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x3E,0x08,0x08,0x08,0x08,0x08,0x30,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x42,0x42,0x42,0x42,0x62,0xDC,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x08,0x08,0x00,0x00},/*"v",86*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xEB,0x49,0x49,0x55,0x55,0x22,0x22,0x00,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x76,0x24,0x18,0x18,0x18,0x24,0x6E,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x18,0x08,0x08,0x07},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x22,0x10,0x08,0x08,0x44,0x7E,0x00,0x00},/*"z",90*/
{0x00,0xC0,0x20,0x20,0x20,0x20,0x20,0x10,0x20,0x20,0x20,0x20,0x20,0x20,0xC0,0x00},/*"{",91*/
{0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10},/*"|",92*/
{0x00,0x06,0x08,0x08,0x08,0x08,0x08,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x06,0x00},/*"}",93*/
{0x0C,0x32,0xC2,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/
}; 
const unsigned char asc2_2412[12][48]={
#if 1
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xE0,0x1F,0xC0,0x6F,0xD0,0x77,0xB0,0x70,0x30,
0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,0x20,0x10,0x70,0x30,0x70,0x30,
0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,0x67,0xD0,0x6F,0xE0,0x1F,0xE0,0x1F,0xE0},/*"0",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x00,0x78,0x00,0x36,0x00,0x2E,0x00,0x0E,0x00,
0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x0E,0x00,
0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x04,0x00},/*"1",1*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xF0,0x7F,0xE0,0x7F,0xE0,0x3F,0xD0,0x00,0x30,
0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x1F,0xD0,0x1F,0xE0,0x2F,0xE0,0x77,0xE0,
0x70,0x00,0x70,0x00,0x70,0x00,0x60,0x00,0x6F,0xF0,0x5F,0xF0,0x3F,0xF0,0x3F,0xF0},/*"2",2*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xF0,0x7F,0xF0,0x7F,0xE0,0x3F,0xD0,0x00,0x30,
0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x3F,0xB0,0x7F,0xD0,0x7F,0xD0,0x3F,0xB0,
0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x3F,0xD0,0x7F,0xE0,0x7F,0xF0,0x3F,0xF0},/*"3",3*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x10,0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,
0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,0x37,0xB0,0x0F,0xD0,0x0F,0xD0,0x07,0xB0,
0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x10},/*"4",4*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xF0,0x5F,0xF0,0x6F,0xF0,0x77,0xF0,0x70,0x00,
0x70,0x00,0x70,0x00,0x70,0x00,0x3F,0x80,0x1F,0xC0,0x1F,0xC0,0x0F,0xB0,0x00,0x30,
0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x3F,0xD0,0x7F,0xD0,0x7F,0xE0,0x3F,0xE0},/*"5",5*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xF0,0x1F,0xF0,0x6F,0xF0,0x77,0xF0,0x70,0x00,
0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,0x77,0xC0,0x2F,0xC0,0x6F,0xD0,0x77,0xB0,
0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,0x67,0xD0,0x6F,0xE0,0x1F,0xE0,0x1F,0xE0},/*"6",6*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xE0,0x7F,0xE0,0x7F,0xD0,0x3F,0x90,0x00,0x30,
0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x10,0x00,0x10,0x00,0x30,
0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x10},/*"7",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xE0,0x1F,0xC0,0x6F,0xD0,0x77,0xB0,0x70,0x30,
0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,0x77,0xB0,0x2F,0xD0,0x6F,0xF0,0x77,0xB0,
0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,0x67,0xD0,0x6F,0xE0,0x1F,0xE0,0x1F,0xC0},/*"8",8*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xE0,0x1F,0xC0,0x6F,0xD0,0x77,0xB0,0x70,0x30,
0x70,0x30,0x70,0x30,0x70,0x30,0x70,0x30,0x6F,0xB0,0x0F,0xD0,0x0F,0xF0,0x0F,0xB0,
0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x3F,0xD0,0x7F,0xE0,0x7F,0xE0,0x3F,0xC0},/*"9",9*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x60,0x00,0x60,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x20,0x00,0x60,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*":",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x3C,0x00,0x3C,0x00,0x3C,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",0*/
#endif
};



typedef struct 
{
       unsigned char Index[2];	
       char Msk[32];
}typFNT_GB16; 
//字体取模：宋体常规小四
const typFNT_GB16 tfont16[]=
{
"系",0x00,0x00,0x00,0x0C,0x3F,0xF8,0x03,0x00,0x06,0x38,0x0C,0x70,0x1F,0xC0,0x03,0x8C,
0x0E,0x0C,0x3F,0xFE,0x0D,0xB6,0x0D,0x98,0x19,0x9C,0x31,0x8C,0x31,0x86,0x67,0x86,/*0*/
"统",0x00,0x00,0x00,0x00,0x18,0x30,0x1B,0xFF,0x30,0x60,0x36,0xCC,0x6C,0xCC,0x7D,0x86,
0x19,0xFE,0x18,0xDB,0x30,0xD8,0x7F,0xD8,0x70,0xDB,0x01,0x9B,0x1F,0x9B,0x77,0x1F,/*1*/
"监",0x00,0x00,0x00,0x00,0x06,0xC0,0x36,0xFF,0x36,0xC0,0x37,0x80,0x37,0xB0,0x37,0x18,
0x06,0x0C,0x00,0x00,0x3F,0xFE,0x36,0x66,0x36,0x66,0x36,0x66,0x36,0x66,0x7F,0xFF,/*2*/
"控",0x00,0x00,0x00,0x00,0x30,0x60,0x30,0x60,0x37,0xFF,0x7E,0xFB,0x37,0x9E,0x33,0x8C,
0x3F,0x06,0x38,0x00,0x31,0xFC,0x70,0x60,0x30,0x60,0x30,0x60,0x30,0x60,0x7F,0xFF,/*3*/
"℃",0xC0,0x00,0x23,0xE8,0x2C,0x18,0xD8,0x08,0x10,0x08,0x30,0x00,0x30,0x00,0x30,0x00,
0x30,0x00,0x30,0x00,0x30,0x00,0x10,0x00,0x18,0x08,0x0C,0x10,0x03,0xE0,0x00,0x00,/*0*/
};
typedef struct 
{
       unsigned char Index[2];	
       char Msk[72];
}typFNT_GB24; 
//字体取模：宋体常规小四
const typFNT_GB24 tfont24[]=
{
"温",0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x0C,0x7F,0xF0,0x04,0x40,0x20,0x04,
0x40,0x20,0x01,0x40,0x20,0x02,0x7F,0xE0,0x62,0x40,0x20,0x32,0x40,0x20,0x12,0x40,
0x20,0x04,0x7F,0xE0,0x04,0x00,0x00,0x05,0x00,0x10,0x04,0xFF,0xF8,0x08,0x89,0x10,
0x78,0x89,0x10,0x18,0x89,0x10,0x18,0x89,0x10,0x18,0x89,0x10,0x18,0x89,0x10,0x18,
0x89,0x16,0x07,0x76,0xE8,0x00,0x00,0x00,/*0*/
"湿",0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00,0x10,0x08,0x7F,0xF8,0x0C,0x60,0x10,0x04,
0x60,0x10,0x01,0x60,0x10,0x42,0x7F,0xF0,0x32,0x60,0x10,0x1A,0x60,0x10,0x12,0x7F,
0xF0,0x04,0x69,0x00,0x04,0x08,0x80,0x05,0x08,0x8C,0x08,0x88,0x8C,0x18,0xC8,0x98,
0x38,0x48,0x90,0x18,0x68,0xA0,0x10,0x48,0xC0,0x10,0x08,0x80,0x30,0x08,0x80,0x10,
0x08,0x8C,0x03,0xF7,0x70,0x00,0x00,0x00,/*1*/
"度",0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x0C,0x08,0x0F,0xFF,0xFC,0x08,
0x40,0x00,0x08,0x30,0xC0,0x08,0x20,0x88,0x08,0x20,0x9C,0x0F,0xFF,0xE0,0x08,0x20,
0x80,0x08,0x20,0x80,0x08,0x3F,0x80,0x08,0x00,0x00,0x19,0xFF,0xE0,0x18,0x20,0xC0,
0x10,0x20,0x80,0x10,0x11,0x80,0x10,0x0B,0x00,0x20,0x06,0x00,0x20,0x1B,0x80,0x40,
0x60,0xFE,0x47,0x80,0x18,0x00,0x00,0x00,/*2*/
"电",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x00,0x00,0x10,0x00,0x00,0x10,0x00,0x00,
0x10,0x00,0x0F,0xFF,0xF0,0x08,0x10,0x20,0x08,0x10,0x20,0x08,0x10,0x20,0x08,0x10,
0x20,0x0F,0xFF,0xE0,0x08,0x10,0x20,0x08,0x10,0x20,0x08,0x10,0x20,0x08,0x10,0x20,
0x0F,0xFF,0xE0,0x08,0x10,0x00,0x00,0x10,0x08,0x00,0x10,0x08,0x00,0x10,0x04,0x00,
0x18,0x0C,0x00,0x0F,0xF8,0x00,0x00,0x00,/*3*/
"压",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x0F,0xFF,0xFC,0x0C,0x00,0x00,0x0C,
0x0C,0x00,0x0C,0x0C,0x00,0x0C,0x0C,0x00,0x0C,0x0C,0x00,0x0C,0x0C,0x00,0x0C,0x0C,
0x00,0x0D,0xFF,0xF0,0x0C,0x0C,0x00,0x0C,0x0C,0x00,0x08,0x0C,0x80,0x08,0x0C,0x40,
0x08,0x0C,0x60,0x08,0x0C,0x30,0x10,0x0C,0x20,0x10,0x0C,0x00,0x20,0x0C,0x0C,0x27,
0xF3,0xF0,0x40,0x00,0x00,0x00,0x00,0x00,/*4*/
"流",0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x06,0x00,0x08,0x02,0x08,0x04,0xFF,0xFC,0x06,
0x04,0x00,0x00,0x04,0x00,0x01,0x08,0x40,0x41,0x10,0x20,0x31,0x20,0x30,0x12,0x7F,
0xD0,0x12,0x00,0x10,0x04,0x64,0x60,0x04,0x64,0x40,0x04,0x64,0x40,0x08,0x64,0x40,
0x78,0x64,0x40,0x18,0x44,0x40,0x18,0x44,0x44,0x18,0xC4,0x44,0x18,0x84,0x44,0x19,
0x04,0x7E,0x06,0x04,0x00,0x00,0x00,0x00,/*5*/
"℃",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x00,0x00,0x12,0x1F,0x80,0x12,
0x30,0x68,0x12,0x60,0x18,0x0C,0xC0,0x18,0x00,0x80,0x08,0x01,0x80,0x08,0x01,0x80,
0x00,0x01,0x80,0x00,0x01,0x80,0x00,0x01,0x80,0x00,0x01,0x80,0x00,0x00,0x80,0x00,
0x00,0xC0,0x00,0x00,0xC0,0x10,0x00,0x60,0x20,0x00,0x38,0xC0,0x00,0x0F,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*,6*/
"：",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x00,0x00,0x1C,0x00,0x00,0x0C,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x00,0x00,0x1C,0x00,0x00,0x1C,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*7*/
"％",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x18,0x08,
0x80,0x30,0x08,0x80,0x60,0x08,0x80,0xC0,0x08,0x81,0x80,0x08,0x81,0x00,0x08,0x82,
0x00,0x05,0x04,0x00,0x02,0x08,0x00,0x00,0x11,0xE0,0x00,0x21,0x10,0x00,0x41,0x10,
0x00,0x83,0x10,0x01,0x03,0x10,0x02,0x01,0x10,0x04,0x01,0x10,0x08,0x00,0xE0,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*0*/
"Ｖ",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0xC1,0xF0,0x03,
0x00,0x40,0x03,0x00,0x40,0x01,0x00,0x80,0x01,0x80,0x80,0x01,0x81,0x00,0x00,0xC1,
0x00,0x00,0xC3,0x00,0x00,0x62,0x00,0x00,0x62,0x00,0x00,0x24,0x00,0x00,0x34,0x00,
0x00,0x18,0x00,0x00,0x18,0x00,0x00,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*0*/
"Ａ",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x08,0x00,0x00,0x18,0x00,0x00,0x1C,0x00,0x00,0x2C,0x00,0x00,0x24,0x00,0x00,0x66,
0x00,0x00,0x46,0x00,0x00,0xC3,0x00,0x00,0x83,0x00,0x00,0xFF,0x00,0x01,0x01,0x80,
0x01,0x01,0x80,0x02,0x00,0xC0,0x02,0x00,0xC0,0x0F,0x83,0xF0,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*1*/
};  
typedef struct 
{
       unsigned char Index[2];	
       char Msk[128];
}typFNT_GB32; 
//字体取模：宋体常规小四
const typFNT_GB32 tfont32[]=
{
"字",0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0xC0,0x00,
0x00,0x01,0xC0,0xC0,0x00,0x01,0x07,0xC0,0x00,0x01,0xFF,0x00,0x02,0x1F,0xFE,0x00,
0x07,0xF0,0x1C,0x00,0x07,0xC0,0x70,0x00,0x0F,0x00,0xE0,0x00,0x0E,0x03,0xF0,0x00,
0x1C,0x0F,0xF0,0x00,0x3C,0x0F,0x70,0x00,0x3C,0x00,0xE0,0x00,0x18,0x00,0xC0,0x00,
0x00,0x00,0xC0,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x20,0x00,
0x00,0x00,0x37,0x00,0x00,0x01,0xFF,0x00,0x00,0x7F,0xF8,0x00,0x07,0xF8,0x30,0x00,
0x1F,0x80,0x30,0x00,0x00,0x80,0x30,0x00,0x00,0xC0,0x30,0x00,0x00,0x60,0x60,0x00,
0x00,0x18,0xE0,0x00,0x00,0x0F,0xC0,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x00,0x00,/*0*/
};
#endif

这一切足够了

发布了12 篇原创文章 · 获赞 22 · 访问量 6009

私信关注

stm32驱动1.44寸LCD屏幕显示中文字符包含可移植keil5工程代码

1.44寸LCD屏幕

猜你喜欢