STM32的SPI查询方式传输测试

               

STM32的SPI查询方式传输测试

本文博客链接:http://blog.csdn.net/jdh99,作者:jdh,转载请注明.

环境：

主机:WIN7

开发环境:MDK4.23

MCU:STM32F103CBT6

 

说明:

软件设置NSS脚,利用查询方式传输

 

源代码:

初始化代码:

//关闭SPISPI_Cmd(SPI1,DISABLE);//初始化SPI接口的SSN脚以及NTRX的RST脚NtrxCtrlInit();//初始化SPI时钟 RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1 | RCC_APB2Periph_GPIOA,ENABLE);//配置SPI1引脚:SCK, MISO and MOSIGPIO_InitStructure.GPIO_Pin = GPIO_Pin_5 | GPIO_Pin_6 | GPIO_Pin_7;GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP ;GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz ;GPIO_Init( GPIOA, &GPIO_InitStructure );// SPI1配置SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex ;SPI_InitStructure.SPI_Mode = SPI_Mode_Master ;SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b ;SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low ;SPI_InitStructure.SPI_CPHA = SPI_CPHA_1Edge ;SPI_InitStructure.SPI_NSS = SPI_NSS_Soft ;//SPI波特率分频设置:4MSPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_8 ;//SPI设置成LSB模式SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_LSB ;SPI_InitStructure.SPI_CRCPolynomial = 7 ;SPI_Init( SPI1, &SPI_InitStructure ) ;//启动SPISPI_Cmd(SPI1,ENABLE);

发送代码:

//SPI发送一个字节static uint8 SPI_SendByte(uint8 Data){ // Loop while DR register in not emplty while( SPI_I2S_GetFlagStatus( SPI1, SPI_I2S_FLAG_TXE ) == RESET ) ; // Send byte through the SPI1 peripheral SPI_I2S_SendData( SPI1, Data ) ; // Wait to receive a byte while( SPI_I2S_GetFlagStatus( SPI1, SPI_I2S_FLAG_RXNE ) == RESET ) ; // Return the byte read from the SPI bus return SPI_I2S_ReceiveData( SPI1 ) ;}

接收代码:

//SPI读取一个字节void SPI_ReadBytes( uint8 Addr, NtrxBufferPtr Buffer, uint8 Len ){ if( ( Len > 0x80 ) || ( Len == 0 ) )  Len = 1 ; SPI_SendByte( Len ) ; SPI_SendByte( Addr ) ; while( Len-- )    {     *Buffer = SPI_SendByte( 0xFF ) ;  Buffer ++ ; }}

NSS脚电平设置:

//SSN脚拉低,开始发送数据void NtrxSSN_Lo( void ){ GPIO_ResetBits( NTRX_SSN_PORT, NTRX_SSN_PIN ) ;}//SSN脚置高,结束发送数据void NtrxSSN_Hi( void ){ GPIO_SetBits( NTRX_SSN_PORT, NTRX_SSN_PIN ) ;}

示例代码:

uint8 NtrxReadSingleSPI( uint8 Addr ){ NtrxBufferType r ; NtrxSSN_Lo() ; SPI_ReadBytes( Addr, &r, 1 ) ; NtrxSSN_Hi() ; return r ;}

输出:

黄线为NSS脚电平,蓝线为CLK电平.