版权声明：本文为博主原创文章，未经博主允许不得转载。 https://blog.csdn.net/qq_28877125/article/details/82868010
windows10 环境下，编译完成之后下载到模块里面去：
一、编译信息
编译信息如下：
> Executing task: aos make linkkitapp@mk3060 <
aos-cube version: 0.2.60
Check if required tools for mk3060 exist
Build AOS Now
TOOLCHAIN_PATH=D:/Output/AliOS/AliOS-Things/build/compiler/gcc-arm-none-eabi/Win32/bin/
Components: linkkitapp board_mk3060 moc108 vcall kernel_init auto_component linkkit_sdk iotx-hal netmgr framework libywss uOTA cjson cli armv5 newlib_stub rhino yloop kv alicrypto digest_algorithm net framework_runtime app_runtime libprov activation chip_code mbedtls hal log vfs irot vfs_device libkm libplat_gen
Skipping building bootloader due to \"total\" is not set
Making out/linkkitapp@mk3060/ld/mx108.ld
Compiling auto_component
Making out/linkkitapp@mk3060/libraries/auto_component.a
Making [email protected]
Making [email protected]
Making [email protected]
AOS MEMORY MAP
|=================================================================|
| MODULE | ROM | RAM |
|=================================================================|
| newlib_stub | 296 | 0 |
| alicrypto | 40100 | 8784 |
| kv | 2929 | 36 |
| libc_nano | 29062 | 464 |
| vcall | 6013 | 4 |
| kernel_init | 1147 | 48 |
| rhino | 14225 | 7721 |
| libplat_gen | 513 | 0 |
| framework | 240 | 12 |
| uOTA | 13345 | 858 |
| vfs | 1875 | 1209 |
| digest_algorithm | 224 | 0 |
| libgcc | 6168 | 0 |
| linkkitapp | 19898 | 22 |
| activation | 2743 | 8776 |
| chip_code | 298 | 240 |
| libprov | 624 | 0 |
| libywss | 40256 | 1442 |
| yloop | 1421 | 24 |
| board_mk3060 | 598 | 24 |
| iotx-hal | 7583 | 224 |
| moc108 | 346 | 32 |
| armv5 | 388 | 0 |
| netmgr | 1823 | 246 |
| libmoc108 | 165113 | 52761 |
| mbedtls | 27953 | 76 |
| cjson | 1958 | 20 |
| libiot_sdk | 373371 | 3172 |
| log | 402 | 20 |
| net | 46165 | 3676 |
| cli | 5945 | 549 |
| hal | 478 | 12 |
| *fill* | 555 | 192 |
|=================================================================|
| TOTAL (bytes) | 814055 | 90644 |
|=================================================================|
870468
55a091ce758cbd91d263de6360df4b85
Build complete
Making .gdbinit
内存
ROM：0.81MB
RAM：90.644KB
| 模组 | RAM | Flash |
|---|---|---|
| EMW3060 | 256KB | 2MB |
上电复位之后
enter low level!
mac fc:ee:e6: 8:6c:b7
leave low level!
app_init finished
start-----------hal
trace config close!!!
[000004]<V> aos framework init.
[000004]<V> IOTX_AWSS_START
awss version: smarthome-bd18d6d<DEBUG> [zconfig_init#2115] : awss lib smarthome-bd18d6d
Soft_AP_start
chan 1
[1] ssid:CMCC-WEB, mac:5866ba6f6760, chn:1, auth:open, none, none, rssi:-236, adha:0
[2] ssid:CMCC, mac:5866ba6f6761, chn:1, auth:wpa2-8021x, aes, aes, rssi:-236, adha:0
由上可知，linkkitapp例程开始之后就会进入配网模式，这在代码中怎么体现的呢？
二、代码分析
1、哪里是入口主函数？
int application_start(int argc, char **argv)
{
aos_set_log_level(AOS_LL_DEBUG);
printf("Hello liefyuan\r\n");
netmgr_init();
aos_register_event_filter(EV_KEY, linkkit_key_process, NULL);
aos_register_event_filter(EV_WIFI, wifi_service_event, NULL);
aos_register_event_filter(EV_YUNIO, cloud_service_event, NULL);
set_iotx_info();
aos_task_new("netmgr", start_netmgr, NULL, 4096);
aos_loop_run();
return 0;
}
打印了信息，说明确实是以这个函数作为入口的。
enter low level!
mac fc:ee:e6: 8:6c:b7
leave low level!
app_init finished
start-----------hal
trace config close!!!
[000004]<V> aos framework init.
Hello liefyuan
[000004]<V> IOTX_AWSS_START
2、哪里是进入配网模式的？
死办法，如下：
int application_start(int argc, char **argv)
{
aos_set_log_level(AOS_LL_DEBUG);
printf("Hello 1\r\n");
netmgr_init();
printf("Hello 2\r\n");
aos_register_event_filter(EV_KEY, linkkit_key_process, NULL);
printf("Hello 3\r\n");
aos_register_event_filter(EV_WIFI, wifi_service_event, NULL);
printf("Hello 4\r\n");
aos_register_event_filter(EV_YUNIO, cloud_service_event, NULL);
printf("Hello 5\r\n");
set_iotx_info();
printf("Hello 6\r\n");
aos_task_new("netmgr", start_netmgr, NULL, 4096);
printf("Hello 7\r\n");
aos_loop_run();
printf("Hello 8\r\n");
return 0;
}
打印信息
trace config close!!!
[000004]<V> aos framework init.
Hello 1
Hello 2
Hello 3
Hello 4
Hello 5
Hello 6
Hello 7
[000006]<V> IOTX_AWSS_START
awss version: smarthome-bd18d6d<DEBUG> [zconfig_init#2115] : awss lib smarthome-bd18d6d
Soft_AP_start
可以推测出来，以下就是进入配网模式的函数。
aos_task_new("netmgr", start_netmgr, NULL, 4096);
3、配网模式函数：aos_task_new(“netmgr”, start_netmgr, NULL, 4096);
看看它的的定义：
可以看出这是个任务创建函数，有点FreeRTOS的任务创建风格。路径为：AliOS-Things\include\aos\kernel.h
/**
* Create a task.
*
* @param[in] name task name.
* @param[in] fn function to run.
* @param[in] arg argument of the function.
* @param[in] stacksize stack-size in bytes.
*
* @return 0: success.
*/
int aos_task_new(const char *name, void (*fn)(void *), void *arg, int stack_size);
于是知道了start_netmgr是个函数名字，看看这个函数是咋样的：
static void start_netmgr(void *p)
{
iotx_event_regist_cb(linkkit_event_monitor);
netmgr_start(true);
aos_task_exit(0);
}
从函数名上可以看到，这个函数里面注册了一个事件回调函数：
/**
* @brief event list used for iotx_regist_event_monitor_cb
*/
enum iotx_event_t {
IOTX_AWSS_START = 0x1000, // AWSS start without enbale, just supports device discover
IOTX_AWSS_ENABLE, // AWSS enable
IOTX_AWSS_LOCK_CHAN, // AWSS lock channel(Got AWSS sync packet)
IOTX_AWSS_CS_ERR, // AWSS AWSS checksum is error
IOTX_AWSS_PASSWD_ERR, // AWSS decrypt passwd error
IOTX_AWSS_GOT_SSID_PASSWD, // AWSS parse ssid and passwd successfully
IOTX_AWSS_CONNECT_ADHA, // AWSS try to connnect adha (device discover, router solution)
IOTX_AWSS_CONNECT_ADHA_FAIL, // AWSS fails to connect adha
IOTX_AWSS_CONNECT_AHA, // AWSS try to connect aha (AP solution)
IOTX_AWSS_CONNECT_AHA_FAIL, // AWSS fails to connect aha
IOTX_AWSS_SETUP_NOTIFY, // AWSS sends out device setup information (AP and router solution)
IOTX_AWSS_CONNECT_ROUTER, // AWSS try to connect destination router
IOTX_AWSS_CONNECT_ROUTER_FAIL, // AWSS fails to connect destination router.
IOTX_AWSS_GOT_IP, // AWSS connects destination successfully and got ip address
IOTX_AWSS_SUC_NOTIFY, // AWSS sends out success notify (AWSS sucess)
IOTX_AWSS_BIND_NOTIFY, // AWSS sends out bind notify information to support bind between user and device
IOTX_CONN_CLOUD = 0x2000, // Device try to connect cloud
IOTX_CONN_CLOUD_FAIL, // Device fails to connect cloud, refer to net_sockets.h for error code
IOTX_CONN_CLOUD_SUC, // Device connects cloud successfully
IOTX_RESET = 0x3000, // Linkkit reset success (just got reset response from cloud without any other operation)
};
/**
* @brief register callback to monitor all event from system.
* 注册监控回调函数来监控所有来自系统的事件
* @param callback, when some event occurs, the system will trigger callback to user.
* refer to enum iotx_event_t for event list supported.
* 当有某些时间发生时，系统将触发用户的回调函数，事件列表上列举的事件类型都支持
* @return 0 when success, -1 when fail.
* @note: user should make sure that callback is not block and runs to complete fast.
*/
extern int iotx_event_regist_cb(void (*monitor_cb)(int event));
看看事件监视器函数linkkit_event_monitor()是咋样的：
- linkkit_event_monit函数不能阻塞运行，应该要运行一些能够快速运行的操作
- 如果用户想要做一些费时的复杂操作，用户应该创建一个任务来做，
- 而不是在linkkit_event_monit函数中去做复杂操作。
/*
* Note:
* the linkkit_event_monitor must not block and should run to complete fast
* if user wants to do complex operation with much time,
* user should post one task to do this, not implement complex operation in
* linkkit_event_monitor
*/
static void linkkit_event_monitor(int event)
{
switch (event) {
case IOTX_AWSS_START: // AWSS start without enbale, just supports device
// discover
// operate led to indicate user
LOG("IOTX_AWSS_START");
break;
case IOTX_AWSS_ENABLE: // AWSS enable
LOG("IOTX_AWSS_ENABLE");
// operate led to indicate user
break;
case IOTX_AWSS_LOCK_CHAN: // AWSS lock channel(Got AWSS sync packet)
LOG("IOTX_AWSS_LOCK_CHAN");
// operate led to indicate user
break;
case IOTX_AWSS_PASSWD_ERR: // AWSS decrypt passwd error
LOG("IOTX_AWSS_PASSWD_ERR");
// operate led to indicate user
break;
case IOTX_AWSS_GOT_SSID_PASSWD:
LOG("IOTX_AWSS_GOT_SSID_PASSWD");
// operate led to indicate user
break;
case IOTX_AWSS_CONNECT_ADHA: // AWSS try to connnect adha (device
// discover, router solution)
LOG("IOTX_AWSS_CONNECT_ADHA");
// operate led to indicate user
break;
case IOTX_AWSS_CONNECT_ADHA_FAIL: // AWSS fails to connect adha
LOG("IOTX_AWSS_CONNECT_ADHA_FAIL");
// operate led to indicate user
break;
case IOTX_AWSS_CONNECT_AHA: // AWSS try to connect aha (AP solution)
LOG("IOTX_AWSS_CONNECT_AHA");
// operate led to indicate user
break;
case IOTX_AWSS_CONNECT_AHA_FAIL: // AWSS fails to connect aha
LOG("IOTX_AWSS_CONNECT_AHA_FAIL");
// operate led to indicate user
break;
case IOTX_AWSS_SETUP_NOTIFY: // AWSS sends out device setup information
// (AP and router solution)
LOG("IOTX_AWSS_SETUP_NOTIFY");
// operate led to indicate user
break;
case IOTX_AWSS_CONNECT_ROUTER: // AWSS try to connect destination router
LOG("IOTX_AWSS_CONNECT_ROUTER");
// operate led to indicate user
break;
case IOTX_AWSS_CONNECT_ROUTER_FAIL: // AWSS fails to connect destination
// router.
LOG("IOTX_AWSS_CONNECT_ROUTER_FAIL");
// operate led to indicate user
break;
case IOTX_AWSS_GOT_IP: // AWSS connects destination successfully and got
// ip address
LOG("IOTX_AWSS_GOT_IP");
// operate led to indicate user
break;
case IOTX_AWSS_SUC_NOTIFY: // AWSS sends out success notify (AWSS
// sucess)
LOG("IOTX_AWSS_SUC_NOTIFY");
// operate led to indicate user
break;
case IOTX_AWSS_BIND_NOTIFY: // AWSS sends out bind notify information to
// support bind between user and device
LOG("IOTX_AWSS_BIND_NOTIFY");
// operate led to indicate user
break;
case IOTX_CONN_CLOUD: // Device try to connect cloud
LOG("IOTX_CONN_CLOUD");
// operate led to indicate user
break;
case IOTX_CONN_CLOUD_FAIL: // Device fails to connect cloud, refer to
// net_sockets.h for error code
LOG("IOTX_CONN_CLOUD_FAIL");
// operate led to indicate user
break;
case IOTX_CONN_CLOUD_SUC: // Device connects cloud successfully
LOG("IOTX_CONN_CLOUD_SUC");
// operate led to indicate user
break;
case IOTX_RESET: // Linkkit reset success (just got reset response from
// cloud without any other operation)
LOG("IOTX_RESET");
// operate led to indicate user
break;
default:
break;
}
}