原文链接:http://tutorials.jenkov.com/java-nio/file-channel.html
Java NIO中的FileChannel是一个连接到文件的通道。可以通过文件通道读写文件。
FileChannel无法设置为非阻塞模式,它总是运行在阻塞模式下。
在使用FileChannel之前,必须先打开它。但是,我们无法直接打开一个FileChannel,需要通过使用一个InputStream、OutputStream或RandomAccessFile来获取一个FileChannel实例。下面是通过RandomAccessFile打开FileChannel的示例:
RandomAccessFile aFile = new RandomAccessFile("data/nio-data.txt", "rw");
FileChannel inChannel = aFile.getChannel();
从FileChannel读取数据
读取文件通道的数据可以通过read方法:
ByteBuffer buf = ByteBuffer.allocate(48);
int bytesRead = inChannel.read(buf);
首先开辟一个Buffer,从通道中读取的数据会写入Buffer内。接着就可以调用read方法,read的返回值代表有多少字节被写入了Buffer,返回-1则表示已经读取到文件结尾了。
向文件通道写入数据(Writing Data to a FileChannel)
使用FileChannel.write()方法向FileChannel写数据,该方法的参数是一个Buffer。如:
String newData = "New String to write to file..." + System.currentTimeMillis();
ByteBuffer buf = ByteBuffer.allocate(48);
buf.clear();
buf.put(newData.getBytes());
buf.flip();
while(buf.hasRemaining()) {
channel.write(buf);
}
注意FileChannel.write()是在while循环中调用的。因为无法保证write()方法一次能向FileChannel写入多少字节,因此需要重复调用write()方法,直到Buffer中已经没有尚未写入通道的字节。
关闭通道(Closing a FileChannel)
操作完毕后,需要把通道关闭:
channel.close();
FileChannel的position方法
有时可能需要在FileChannel的某个特定位置进行数据的读/写操作。可以通过调用position()方法获取FileChannel的当前位置。
也可以通过调用position(long pos)方法设置FileChannel的当前位置。
这里有两个例子:
long pos channel.position();
channel.position(pos +123);
假设我们把当前位置设置为文件结尾之后,那么当我们视图从通道中读取数据时就会发现返回值是-1,表示已经到达文件结尾了。 如果把当前位置设置为文件结尾之后,在想通道中写入数据,文件会自动扩展以便写入数据,但是这样会导致文件中出现类似空洞,即文件的一些位置是没有数据的。
FileChannel的size方法
FileChannel实例的size()方法FileChannel对应的文件的文件大小:
long fileSize = channel.size();
FileChannel的truncate方法
可以使用FileChannel.truncate()方法截取一个文件。截取文件时,文件将中指定长度后面的部分将被删除。如:
channel.truncate(1024);
这个例子截取文件的前1024个字节。
FileChannel Force
force方法会把所有未写磁盘的数据都强制写入磁盘。这是因为在操作系统中出于性能考虑回把数据放入缓冲区,所以不能保证数据在调用write写入文件通道后就及时写到磁盘上了,除非手动调用force方法。 force方法需要一个布尔参数,代表是否把meta data也一并强制写入。
channel.force(true);