目录
1.前言：
没玩儿过GXP、GTX或者更高端的GTH、GTZ，都不好意思说自己玩儿过FPGA，这么说不怕得罪一大帮兄弟，事实的确如此，试想，如果你只玩儿过FPGA的流水灯、串口、I2C、图像处理之类的，其实并没有接触到FPGA的核心点，为啥呢？FPGA的流水灯、串口、I2C之类的东西，我一个stm32单片机足以，图像处理之类的我一个TI的DSP也可以，实在不行我上海思之类的也足以，那么你FPGA还有啥特别的？器件贵功耗还高；
但高速串行收发器呢？比如GTX，在FPGA面前，还有谁？呵呵~~
2.工程整体框架：
工程整体框架如下：
视频源：提供了两套工程，一个视频源是OV5640，另一个是HDMI输入，IT6802解码，关于IT6802解码部分，可以参考我之前的文章点击查看：IT6802解码HDMI视频
视频采集：OV5640和HDMI都采集为rgb888格式视频；
数据编码：将采集的rgb888格式视频数据编码为32为并行数据；
GTX：使用Xilinx官方IP实现，负责GTX的串并/并串转换：
SFP1：GTX发送接口，用过SFP线缆与SFP2连接，形成环路；
SFP2：GTX接收接口，用过SFP线缆与SFP1连接，形成环路；
数据对齐：接收GTX的串并转换后的32位数据，并对错位数据进行重新对齐，保证数据的完整性；
数据解码：将GTX的串并转换后的32位数据还原位带有vs、de和rgb888格式的视频流数据；
FDMA：负责对vs、de和rgb888格式的视频流数据做三帧缓存处理，使得输出视频变得流畅，关于FDMA部分可以参考我之前的文章点击查看：FDMA视频三帧缓存
DDR3：外设，缓存视频的内存；
视频时序：负责生成输出视频所需的时序，严格参照VASE标准设计；
HDMI输出：使用Xilinx官方原语设计的HDMI输出模块，负责将视频输出到显示器；
3.GTX IP 配置及细节讲解
前面的内容纯属装B，别当真。直接上干活：
在vivado里搜 7 series，就会出现这个ip，然后添加进来：
第一页选默认：
下一页全是重点，拿出小本本：
重点1：由于我们使用8bit/10bit编解码协议，所以选他；
下面的重点全部跟你板子的原理图密切相关，所以具体情况具体参考你的板子原理图，但方法是一样的；
重点2：线速率与参考时钟的选择：
记住，线速率的选择取决于GTX差分时钟，具体看你的板子原理图，以我的板子为例，如下：
原理图可知，GTX的BANK115的REFCLK0接到了148.5的差分时钟，也就是说，我们的GTX参考时钟是148.5M；
补充一句，市面上的FPGA开发板(某原子某联某金)基本都是125M时钟，如果你自己的板子跟他们的板子时钟不一样，拿到他们的例程或教程跟着做时，估计你会一脸懵逼，这里不知道怎么配置了，哈哈。
好了说正事儿，既然参考时钟定了，那就剩下线速率的配置了，线速率=n参考时钟；
我的光模块最高能跑10G，所以就选择一个中间值吧，148.54=5.94G；
这下应该知道线速率和参考时钟怎么选了吧。
重点3：PLL选择；
这里可以选择CPLL和QPLL，都没问题；
重点4：收发引脚和时钟选择；
先看收发引脚，我的板子是K7-325T-FGG676，所以只有两个GTX，分别位于BANK115和BANK116，板子上有2个SFP接口，都连接在BANK115，原理图部分如下：
原理图可知：SFP1的收发引脚连接到了X0Y0；SFP2的收发引脚连接到了X0Y3；
？？？？？？咋得来的？
要说清楚这个问题，先看看GTX的组成；
我的板子只有2个GTX的基本组成是QUAD，简称Q，分为Q0和Q1，其中Q0对应BANM115，Q1对应BANM116，1个Q由4个GTPE2_CHANNEL和1个GTPE2_COMMON组成，具体去Xilinx官网看官方资料吧。
4个GTPE2_CHANNEL实际上就是4路GTX收发通道，命名和排序分别是：X0Y0、X0Y1、X0Y2、X0Y3，对应原理图中BANK115中的0~3；
这么讲应该能明白了；
所以我们需要使能X0Y0和X0Y3，也就是在小框里选√；
再根据前面的原理图可知：
参考时钟位于Q0的REFCLK0；
SFP1位于Q0的X0Y0；
SFP2位于Q0的X0Y3；
所以：重点4和重点5的选择就是这么来的，解析完毕；
下一页配置如下：
基本都是默认配置；
后面的配置都保持默认即可，然后生成IP；
然后打开官方例程：
然后打开官方例程的顶层文件，然后就是自由的DIY魔改了，
下面直接给出我的魔改方案源码：
`timescale 1ns / 1ps
`define DLY #1
(* DowngradeIPIdentifiedWarnings="yes" *)
//***********************************Entity Declaration************************
(* CORE_GENERATION_INFO = "gtwizard_0,gtwizard_v3_6_11,{protocol_file=aurora_8b10b_single_lane_4byte}" *)
module gtwizard_0_exdes #
(
parameter EXAMPLE_CONFIG_INDEPENDENT_LANES = 1,//configuration for frame gen and check
parameter EXAMPLE_LANE_WITH_START_CHAR = 0, // specifies lane with unique start frame char
parameter EXAMPLE_WORDS_IN_BRAM = 512, // specifies amount of data in BRAM
parameter EXAMPLE_SIM_GTRESET_SPEEDUP = "FALSE", // simulation setting for GT SecureIP model
parameter EXAMPLE_USE_CHIPSCOPE = 0, // Set to 1 to use Chipscope to drive resets
parameter STABLE_CLOCK_PERIOD = 10
)
(
input wire Q0_CLK0_GTREFCLK_PAD_N_IN,
input wire Q0_CLK0_GTREFCLK_PAD_P_IN,
//input wire DRP_CLK_IN_P,
//input wire DRP_CLK_IN_N,
//output wire TRACK_DATA_OUT,
//sfp1
output o_sfp1_tx_clk ,
input [31:0] i_sfp1_tx_data ,
input [3: 0] i_sfp1_tx_kchar,
output o_sfp1_rx_clk ,
output [31:0] o_sfp1_rx_data ,
output [3: 0] o_sfp1_rx_kchar,
output o_sfp1_tx_rstn ,
output o_sfp1_rx_rstn ,
//sfp2
output o_sfp2_tx_clk ,
input [31:0] i_sfp2_tx_data ,
input [3: 0] i_sfp2_tx_kchar,
output o_sfp2_rx_clk ,
output [31:0] o_sfp2_rx_data ,
output [3: 0] o_sfp2_rx_kchar,
output o_sfp2_tx_rstn ,
output o_sfp2_rx_rstn ,
input drp_clk_100m,
input wire [1:0] RXN_IN,
input wire [1:0] RXP_IN,
output wire [1:0] TXN_OUT,
output wire [1:0] TXP_OUT,
output [1:0] sfp_tx_disable
);
assign drpclk_in_i=drp_clk_100m;
assign sfp_tx_disable=2'b00;
//sfp1
assign o_sfp1_tx_clk = gt0_txusrclk2_i ;//用户发送时钟
assign o_sfp1_rx_clk = gt0_rxusrclk2_i ;//用户接收时钟
assign gt0_txdata_i = i_sfp1_tx_data ;//用户发送数据
assign gt0_txcharisk_i = i_sfp1_tx_kchar ;//用户发送K码
assign o_sfp1_rx_data = gt0_rxdata_i ;//用户接收数据
assign o_sfp1_rx_kchar = gt0_rxcharisk_i ;//用户接收K码
assign o_sfp1_tx_rstn = gt0_txfsmresetdone_i ;//gtx初始化完成标志
assign o_sfp1_rx_rstn = gt0_rxfsmresetdone_i ;//gtx初始化完成标志
//sfp2
assign o_sfp2_tx_clk = gt1_txusrclk2_i ;
assign o_sfp2_rx_clk = gt1_rxusrclk2_i ;
assign gt1_txdata_i = i_sfp2_tx_data ;
assign gt1_txcharisk_i = i_sfp2_tx_kchar ;
assign o_sfp2_rx_data = gt1_rxdata_i ;
assign o_sfp2_rx_kchar = gt1_rxcharisk_i ;
assign o_sfp2_tx_rstn = gt1_txfsmresetdone_i ;//gtx初始化完成标志
assign o_sfp2_rx_rstn = gt1_rxfsmresetdone_i ;//gtx初始化完成标志
wire soft_reset_i;
(*mark_debug = "TRUE" *) wire soft_reset_vio_i;
//************************** Register Declarations ****************************
wire gt_txfsmresetdone_i;
wire gt_rxfsmresetdone_i;
(* ASYNC_REG = "TRUE" *)reg gt_txfsmresetdone_r;
(* ASYNC_REG = "TRUE" *)reg gt_txfsmresetdone_r2;
wire gt0_txfsmresetdone_i;
wire gt0_rxfsmresetdone_i;
(* ASYNC_REG = "TRUE" *)reg gt0_txfsmresetdone_r;
(* ASYNC_REG = "TRUE" *)reg gt0_txfsmresetdone_r2;
(* ASYNC_REG = "TRUE" *)reg gt0_rxfsmresetdone_r;
(* ASYNC_REG = "TRUE" *)reg gt0_rxfsmresetdone_r2;
(* ASYNC_REG = "TRUE" *)reg gt0_rxresetdone_r;
(* ASYNC_REG = "TRUE" *)reg gt0_rxresetdone_r2;
(* ASYNC_REG = "TRUE" *)reg gt0_rxresetdone_r3;
(* ASYNC_REG = "TRUE" *)reg gt0_rxresetdone_vio_r;
(* ASYNC_REG = "TRUE" *)reg gt0_rxresetdone_vio_r2;
(* ASYNC_REG = "TRUE" *)reg gt0_rxresetdone_vio_r3;
wire gt1_txfsmresetdone_i;
wire gt1_rxfsmresetdone_i;
(* ASYNC_REG = "TRUE" *)reg gt1_txfsmresetdone_r;
(* ASYNC_REG = "TRUE" *)reg gt1_txfsmresetdone_r2;
(* ASYNC_REG = "TRUE" *)reg gt1_rxfsmresetdone_r;
(* ASYNC_REG = "TRUE" *)reg gt1_rxfsmresetdone_r2;
(* ASYNC_REG = "TRUE" *)reg gt1_rxresetdone_r;
(* ASYNC_REG = "TRUE" *)reg gt1_rxresetdone_r2;
(* ASYNC_REG = "TRUE" *)reg gt1_rxresetdone_r3;
(* ASYNC_REG = "TRUE" *)reg gt1_rxresetdone_vio_r;
(* ASYNC_REG = "TRUE" *)reg gt1_rxresetdone_vio_r2;
(* ASYNC_REG = "TRUE" *)reg gt1_rxresetdone_vio_r3;
reg [5:0] reset_counter = 0;
reg [3:0] reset_pulse;
//**************************** Wire Declarations ******************************//
//------------------------ GT Wrapper Wires ------------------------------
//________________________________________________________________________
//________________________________________________________________________
//GT0 (X1Y0)
//-------------------------- Channel - DRP Ports --------------------------
wire [8:0] gt0_drpaddr_i;
wire [15:0] gt0_drpdi_i;
wire [15:0] gt0_drpdo_i;
wire gt0_drpen_i;
wire gt0_drprdy_i;
wire gt0_drpwe_i;
//------------------------- Digital Monitor Ports --------------------------
wire [7:0] gt0_dmonitorout_i;
//----------------------------- Loopback Ports -----------------------------
wire [2:0] gt0_loopback_i;
//---------------------------- Power-Down Ports ----------------------------
wire [1:0] gt0_rxpd_i;
wire [1:0] gt0_txpd_i;
//------------------- RX Initialization and Reset Ports --------------------
wire gt0_eyescanreset_i;
wire gt0_rxuserrdy_i;
//------------------------ RX Margin Analysis Ports ------------------------
wire gt0_eyescandataerror_i;
wire gt0_eyescantrigger_i;
//----------------------- Receive Ports - CDR Ports ------------------------
wire gt0_rxcdrhold_i;
wire gt0_rxcdrovrden_i;
//----------------- Receive Ports - Clock Correction Ports -----------------
wire [1:0] gt0_rxclkcorcnt_i;
//---------------- Receive Ports - FPGA RX interface Ports -----------------
wire [31:0] gt0_rxdata_i;
//----------------- Receive Ports - Pattern Checker Ports ------------------
wire gt0_rxprbserr_i;
wire [2:0] gt0_rxprbssel_i;
//----------------- Receive Ports - Pattern Checker ports ------------------
wire gt0_rxprbscntreset_i;
//---------------- Receive Ports - RX 8B/10B Decoder Ports -----------------
wire [3:0] gt0_rxdisperr_i;
wire [3:0] gt0_rxnotintable_i;
//------------------------- Receive Ports - RX AFE -------------------------
wire gt0_gtxrxp_i;
//---------------------- Receive Ports - RX AFE Ports ----------------------
wire gt0_gtxrxn_i;
//----------------- Receive Ports - RX Buffer Bypass Ports -----------------
wire gt0_rxbufreset_i;
wire [2:0] gt0_rxbufstatus_i;
//------------ Receive Ports - RX Byte and Word Alignment Ports ------------
wire gt0_rxbyteisaligned_i;
wire gt0_rxbyterealign_i;
wire gt0_rxcommadet_i;
wire gt0_rxmcommaalignen_i;
wire gt0_rxpcommaalignen_i;
//------------------- Receive Ports - RX Equalizer Ports -------------------
wire gt0_rxdfelpmreset_i;
wire [6:0] gt0_rxmonitorout_i;
wire [1:0] gt0_rxmonitorsel_i;
//------------- Receive Ports - RX Fabric Output Control Ports -------------
wire gt0_rxoutclk_i;
wire gt0_rxoutclkfabric_i;
//----------- Receive Ports - RX Initialization and Reset Ports ------------
wire gt0_gtrxreset_i;
wire gt0_rxpcsreset_i;
wire gt0_rxpmareset_i;
//---------------- Receive Ports - RX Margin Analysis ports ----------------
wire gt0_rxlpmen_i;
//--------------- Receive Ports - RX Polarity Control Ports ----------------
wire gt0_rxpolarity_i;
//----------------- Receive Ports - RX8B/10B Decoder Ports -----------------
wire [3:0] gt0_rxchariscomma_i;
wire [3:0] gt0_rxcharisk_i;
//------------ Receive Ports -RX Initialization and Reset Ports ------------
wire gt0_rxresetdone_i;
//---------------------- TX Configurable Driver Ports ----------------------
wire [4:0] gt0_txpostcursor_i;
wire [4:0] gt0_txprecursor_i;
//------------------- TX Initialization and Reset Ports --------------------
wire gt0_gttxreset_i;
wire gt0_txuserrdy_i;
//-------------- Transmit Ports - 8b10b Encoder Control Ports --------------
wire [3:0] gt0_txchardispmode_i;
wire [3:0] gt0_txchardispval_i;
//---------------- Transmit Ports - Pattern Generator Ports ----------------
wire gt0_txprbsforceerr_i;
//-------------------- Transmit Ports - TX Buffer Ports --------------------
wire [1:0] gt0_txbufstatus_i;
//------------- Transmit Ports - TX Configurable Driver Ports --------------
wire [3:0] gt0_txdiffctrl_i;
wire [6:0] gt0_txmaincursor_i;
//---------------- Transmit Ports - TX Data Path interface -----------------
wire [31:0] gt0_txdata_i;
//-------------- Transmit Ports - TX Driver and OOB signaling --------------
wire gt0_gtxtxn_i;
wire gt0_gtxtxp_i;
//--------- Transmit Ports - TX Fabric Clock Output Control Ports ----------
wire gt0_txoutclk_i;
wire gt0_txoutclkfabric_i;
wire gt0_txoutclkpcs_i;
//------------------- Transmit Ports - TX Gearbox Ports --------------------
wire [3:0] gt0_txcharisk_i;
//----------- Transmit Ports - TX Initialization and Reset Ports -----------
wire gt0_txpcsreset_i;
wire gt0_txpmareset_i;
wire gt0_txresetdone_i;
//--------------- Transmit Ports - TX Polarity Control Ports ---------------
wire gt0_txpolarity_i;
//---------------- Transmit Ports - pattern Generator Ports ----------------
wire [2:0] gt0_txprbssel_i;
//________________________________________________________________________
//________________________________________________________________________
//GT1 (X1Y3)
//-------------------------- Channel - DRP Ports --------------------------
wire [8:0] gt1_drpaddr_i;
wire [15:0] gt1_drpdi_i;
wire [15:0] gt1_drpdo_i;
wire gt1_drpen_i;
wire gt1_drprdy_i;
wire gt1_drpwe_i;
//------------------------- Digital Monitor Ports --------------------------
wire [7:0] gt1_dmonitorout_i;
//----------------------------- Loopback Ports -----------------------------
wire [2:0] gt1_loopback_i;
//---------------------------- Power-Down Ports ----------------------------
wire [1:0] gt1_rxpd_i;
wire [1:0] gt1_txpd_i;
//------------------- RX Initialization and Reset Ports --------------------
wire gt1_eyescanreset_i;
wire gt1_rxuserrdy_i;
//------------------------ RX Margin Analysis Ports ------------------------
wire gt1_eyescandataerror_i;
wire gt1_eyescantrigger_i;
//----------------------- Receive Ports - CDR Ports ------------------------
wire gt1_rxcdrhold_i;
wire gt1_rxcdrovrden_i;
//----------------- Receive Ports - Clock Correction Ports -----------------
wire [1:0] gt1_rxclkcorcnt_i;
//---------------- Receive Ports - FPGA RX interface Ports -----------------
wire [31:0] gt1_rxdata_i;
//----------------- Receive Ports - Pattern Checker Ports ------------------
wire gt1_rxprbserr_i;
wire [2:0] gt1_rxprbssel_i;
//----------------- Receive Ports - Pattern Checker ports ------------------
wire gt1_rxprbscntreset_i;
//---------------- Receive Ports - RX 8B/10B Decoder Ports -----------------
wire [3:0] gt1_rxdisperr_i;
wire [3:0] gt1_rxnotintable_i;
//------------------------- Receive Ports - RX AFE -------------------------
wire gt1_gtxrxp_i;
//---------------------- Receive Ports - RX AFE Ports ----------------------
wire gt1_gtxrxn_i;
//----------------- Receive Ports - RX Buffer Bypass Ports -----------------
wire gt1_rxbufreset_i;
wire [2:0] gt1_rxbufstatus_i;
//------------ Receive Ports - RX Byte and Word Alignment Ports ------------
wire gt1_rxbyteisaligned_i;
wire gt1_rxbyterealign_i;
wire gt1_rxcommadet_i;
wire gt1_rxmcommaalignen_i;
wire gt1_rxpcommaalignen_i;
//------------------- Receive Ports - RX Equalizer Ports -------------------
wire gt1_rxdfelpmreset_i;
wire [6:0] gt1_rxmonitorout_i;
wire [1:0] gt1_rxmonitorsel_i;
//------------- Receive Ports - RX Fabric Output Control Ports -------------
wire gt1_rxoutclk_i;
wire gt1_rxoutclkfabric_i;
//----------- Receive Ports - RX Initialization and Reset Ports ------------
wire gt1_gtrxreset_i;
wire gt1_rxpcsreset_i;
wire gt1_rxpmareset_i;
//---------------- Receive Ports - RX Margin Analysis ports ----------------
wire gt1_rxlpmen_i;
//--------------- Receive Ports - RX Polarity Control Ports ----------------
wire gt1_rxpolarity_i;
//----------------- Receive Ports - RX8B/10B Decoder Ports -----------------
wire [3:0] gt1_rxchariscomma_i;
wire [3:0] gt1_rxcharisk_i;
//------------ Receive Ports -RX Initialization and Reset Ports ------------
wire gt1_rxresetdone_i;
//---------------------- TX Configurable Driver Ports ----------------------
wire [4:0] gt1_txpostcursor_i;
wire [4:0] gt1_txprecursor_i;
//------------------- TX Initialization and Reset Ports --------------------
wire gt1_gttxreset_i;
wire gt1_txuserrdy_i;
//-------------- Transmit Ports - 8b10b Encoder Control Ports --------------
wire [3:0] gt1_txchardispmode_i;
wire [3:0] gt1_txchardispval_i;
//---------------- Transmit Ports - Pattern Generator Ports ----------------
wire gt1_txprbsforceerr_i;
//-------------------- Transmit Ports - TX Buffer Ports --------------------
wire [1:0] gt1_txbufstatus_i;
//------------- Transmit Ports - TX Configurable Driver Ports --------------
wire [3:0] gt1_txdiffctrl_i;
wire [6:0] gt1_txmaincursor_i;
//---------------- Transmit Ports - TX Data Path interface -----------------
wire [31:0] gt1_txdata_i;
//-------------- Transmit Ports - TX Driver and OOB signaling --------------
wire gt1_gtxtxn_i;
wire gt1_gtxtxp_i;
//--------- Transmit Ports - TX Fabric Clock Output Control Ports ----------
wire gt1_txoutclk_i;
wire gt1_txoutclkfabric_i;
wire gt1_txoutclkpcs_i;
//------------------- Transmit Ports - TX Gearbox Ports --------------------
wire [3:0] gt1_txcharisk_i;
//----------- Transmit Ports - TX Initialization and Reset Ports -----------
wire gt1_txpcsreset_i;
wire gt1_txpmareset_i;
wire gt1_txresetdone_i;
//--------------- Transmit Ports - TX Polarity Control Ports ---------------
wire gt1_txpolarity_i;
//---------------- Transmit Ports - pattern Generator Ports ----------------
wire [2:0] gt1_txprbssel_i;
//____________________________COMMON PORTS________________________________
//-------------------- Common Block - Ref Clock Ports ---------------------
wire gt0_gtrefclk1_common_i;
//----------------------- Common Block - QPLL Ports ------------------------
wire gt0_qplllock_i;
wire gt0_qpllrefclklost_i;
wire gt0_qpllreset_i;
//----------------------------- Global Signals -----------------------------
wire drpclk_in_i;
wire DRPCLK_IN;
wire gt0_tx_system_reset_c;
wire gt0_rx_system_reset_c;
wire gt1_tx_system_reset_c;
wire gt1_rx_system_reset_c;
wire tied_to_ground_i;
wire [63:0] tied_to_ground_vec_i;
wire tied_to_vcc_i;
wire [7:0] tied_to_vcc_vec_i;
wire GTTXRESET_IN;
wire GTRXRESET_IN;
wire QPLLRESET_IN;
//--------------------------- User Clocks ---------------------------------
wire gt0_txusrclk_i;
wire gt0_txusrclk2_i;
wire gt0_rxusrclk_i;
wire gt0_rxusrclk2_i;
wire gt1_txusrclk_i;
wire gt1_txusrclk2_i;
wire gt1_rxusrclk_i;
wire gt1_rxusrclk2_i;
wire gt0_txmmcm_lock_i;
wire gt0_txmmcm_reset_i;
wire gt0_rxmmcm_lock_i;
wire gt0_rxmmcm_reset_i;
wire gt1_txmmcm_lock_i;
wire gt1_txmmcm_reset_i;
wire gt1_rxmmcm_lock_i;
wire gt1_rxmmcm_reset_i;
//--------------------------- Reference Clocks ----------------------------
wire q0_clk0_refclk_i;
//--------------------- Frame check/gen Module Signals --------------------
wire gt0_matchn_i;
wire [3:0] gt0_txcharisk_float_i;
wire [15:0] gt0_txdata_float16_i;
wire [31:0] gt0_txdata_float_i;
wire gt0_block_sync_i;
wire gt0_track_data_i;
wire [7:0] gt0_error_count_i;
wire gt0_frame_check_reset_i;
wire gt0_inc_in_i;
wire gt0_inc_out_i;
wire [31:0] gt0_unscrambled_data_i;
wire gt1_matchn_i;
wire [3:0] gt1_txcharisk_float_i;
wire [15:0] gt1_txdata_float16_i;
wire [31:0] gt1_txdata_float_i;
wire gt1_block_sync_i;
wire gt1_track_data_i;
wire [7:0] gt1_error_count_i;
wire gt1_frame_check_reset_i;
wire gt1_inc_in_i;
wire gt1_inc_out_i;
wire [31:0] gt1_unscrambled_data_i;
wire reset_on_data_error_i;
wire track_data_out_i;
//--------------------- Chipscope Signals ---------------------------------
(*mark_debug = "TRUE" *)wire rxresetdone_vio_i;
wire [35:0] tx_data_vio_control_i;
wire [35:0] rx_data_vio_control_i;
wire [35:0] shared_vio_control_i;
wire [35:0] ila_control_i;
wire [35:0] channel_drp_vio_control_i;
wire [35:0] common_drp_vio_control_i;
wire [31:0] tx_data_vio_async_in_i;
wire [31:0] tx_data_vio_sync_in_i;
wire [31:0] tx_data_vio_async_out_i;
wire [31:0] tx_data_vio_sync_out_i;
wire [31:0] rx_data_vio_async_in_i;
wire [31:0] rx_data_vio_sync_in_i;
wire [31:0] rx_data_vio_async_out_i;
wire [31:0] rx_data_vio_sync_out_i;
wire [31:0] shared_vio_in_i;
wire [31:0] shared_vio_out_i;
wire [163:0] ila_in_i;
wire [31:0] channel_drp_vio_async_in_i;
wire [31:0] channel_drp_vio_sync_in_i;
wire [31:0] channel_drp_vio_async_out_i;
wire [31:0] channel_drp_vio_sync_out_i;
wire [31:0] common_drp_vio_async_in_i;
wire [31:0] common_drp_vio_sync_in_i;
wire [31:0] common_drp_vio_async_out_i;
wire [31:0] common_drp_vio_sync_out_i;
wire [31:0] gt0_tx_data_vio_async_in_i;
wire [31:0] gt0_tx_data_vio_sync_in_i;
wire [31:0] gt0_tx_data_vio_async_out_i;
wire [31:0] gt0_tx_data_vio_sync_out_i;
wire [31:0] gt0_rx_data_vio_async_in_i;
wire [31:0] gt0_rx_data_vio_sync_in_i;
wire [31:0] gt0_rx_data_vio_async_out_i;
wire [31:0] gt0_rx_data_vio_sync_out_i;
wire [163:0] gt0_ila_in_i;
wire [31:0] gt0_channel_drp_vio_async_in_i;
wire [31:0] gt0_channel_drp_vio_sync_in_i;
wire [31:0] gt0_channel_drp_vio_async_out_i;
wire [31:0] gt0_channel_drp_vio_sync_out_i;
wire [31:0] gt0_common_drp_vio_async_in_i;
wire [31:0] gt0_common_drp_vio_sync_in_i;
wire [31:0] gt0_common_drp_vio_async_out_i;
wire [31:0] gt0_common_drp_vio_sync_out_i;
wire [31:0] gt1_tx_data_vio_async_in_i;
wire [31:0] gt1_tx_data_vio_sync_in_i;
wire [31:0] gt1_tx_data_vio_async_out_i;
wire [31:0] gt1_tx_data_vio_sync_out_i;
wire [31:0] gt1_rx_data_vio_async_in_i;
wire [31:0] gt1_rx_data_vio_sync_in_i;
wire [31:0] gt1_rx_data_vio_async_out_i;
wire [31:0] gt1_rx_data_vio_sync_out_i;
wire [163:0] gt1_ila_in_i;
wire [31:0] gt1_channel_drp_vio_async_in_i;
wire [31:0] gt1_channel_drp_vio_sync_in_i;
wire [31:0] gt1_channel_drp_vio_async_out_i;
wire [31:0] gt1_channel_drp_vio_sync_out_i;
wire [31:0] gt1_common_drp_vio_async_in_i;
wire [31:0] gt1_common_drp_vio_sync_in_i;
wire [31:0] gt1_common_drp_vio_async_out_i;
wire [31:0] gt1_common_drp_vio_sync_out_i;
wire gttxreset_i;
wire gtrxreset_i;
wire mux_sel_i;
wire user_tx_reset_i;
wire user_rx_reset_i;
wire tx_vio_clk_i;
wire tx_vio_clk_mux_out_i;
wire rx_vio_ila_clk_i;
wire rx_vio_ila_clk_mux_out_i;
wire qpllreset_i;
wire [(80 -32) -1:0] zero_vector_rx_80 ;
wire [(8 -4) -1:0] zero_vector_rx_8 ;
wire [79:0] gt0_rxdata_ila ;
wire [1:0] gt0_rxdatavalid_ila;
wire [7:0] gt0_rxcharisk_ila ;
wire gt0_txmmcm_lock_ila ;
wire gt0_rxmmcm_lock_ila ;
wire gt0_rxresetdone_ila ;
wire gt0_txresetdone_ila ;
wire [79:0] gt1_rxdata_ila ;
wire [1:0] gt1_rxdatavalid_ila;
wire [7:0] gt1_rxcharisk_ila ;
wire gt1_txmmcm_lock_ila ;
wire gt1_rxmmcm_lock_ila ;
wire gt1_rxresetdone_ila ;
wire gt1_txresetdone_ila ;
//**************************** Main Body of Code *******************************
// Static signal Assigments
assign tied_to_ground_i = 1'b0;
assign tied_to_ground_vec_i = 64'h0000000000000000;
assign tied_to_vcc_i = 1'b1;
assign tied_to_vcc_vec_i = 8'hff;
assign zero_vector_rx_80 = 0;
assign zero_vector_rx_8 = 0;
assign q0_clk0_refclk_i = 1'b0;
//***********************************************************************//
// //
//--------------------------- The GT Wrapper ----------------------------//
// //
//***********************************************************************//
// Use the instantiation template in the example directory to add the GT wrapper to your design.
// In this example, the wrapper is wired up for basic operation with a frame generator and frame
// checker. The GTs will reset, then attempt to align and transmit data. If channel bonding is
// enabled, bonding should occur after alignment.
// While connecting the GT TX/RX Reset ports below, please add a delay of
// minimum 500ns as mentioned in AR 43482.
gtwizard_0_support #
(
.EXAMPLE_SIM_GTRESET_SPEEDUP ("FALSE"),
.STABLE_CLOCK_PERIOD (10)
)
gtwizard_0_support_i
(
.soft_reset_tx_in (soft_reset_i),
.soft_reset_rx_in (soft_reset_i),
.dont_reset_on_data_error_in (tied_to_ground_i),
.q0_clk0_gtrefclk_pad_n_in(Q0_CLK0_GTREFCLK_PAD_N_IN),
.q0_clk0_gtrefclk_pad_p_in(Q0_CLK0_GTREFCLK_PAD_P_IN),
.gt0_tx_mmcm_lock_out (gt0_txmmcm_lock_i),
.gt0_rx_mmcm_lock_out (gt0_rxmmcm_lock_i),
.gt0_tx_fsm_reset_done_out (gt0_txfsmresetdone_i),
.gt0_rx_fsm_reset_done_out (gt0_rxfsmresetdone_i),
.gt0_data_valid_in (1'b1),
.gt1_tx_mmcm_lock_out (gt1_txmmcm_lock_i),
.gt1_rx_mmcm_lock_out (gt1_rxmmcm_lock_i),
.gt1_tx_fsm_reset_done_out (gt1_txfsmresetdone_i),
.gt1_rx_fsm_reset_done_out (gt1_rxfsmresetdone_i),
.gt1_data_valid_in (1'b1),
.gt0_txusrclk_out(gt0_txusrclk_i),
.gt0_txusrclk2_out(gt0_txusrclk2_i),
.gt0_rxusrclk_out(gt0_rxusrclk_i),
.gt0_rxusrclk2_out(gt0_rxusrclk2_i),
.gt1_txusrclk_out(gt1_txusrclk_i),
.gt1_txusrclk2_out(gt1_txusrclk2_i),
.gt1_rxusrclk_out(gt1_rxusrclk_i),
.gt1_rxusrclk2_out(gt1_rxusrclk2_i),
//_____________________________________________________________________
//_____________________________________________________________________
//GT0 (X1Y0)
//-------------------------- Channel - DRP Ports --------------------------
.gt0_drpaddr_in (gt0_drpaddr_i),
.gt0_drpdi_in (gt0_drpdi_i),
.gt0_drpdo_out (gt0_drpdo_i),
.gt0_drpen_in (gt0_drpen_i),
.gt0_drprdy_out (gt0_drprdy_i),
.gt0_drpwe_in (gt0_drpwe_i),
//------------------------- Digital Monitor Ports --------------------------
.gt0_dmonitorout_out (gt0_dmonitorout_i),
//----------------------------- Loopback Ports -----------------------------
.gt0_loopback_in (gt0_loopback_i),
//---------------------------- Power-Down Ports ----------------------------
.gt0_rxpd_in (gt0_rxpd_i),
.gt0_txpd_in (gt0_txpd_i),
//------------------- RX Initialization and Reset Ports --------------------
.gt0_eyescanreset_in (tied_to_ground_i),
.gt0_rxuserrdy_in (tied_to_vcc_i),
//------------------------ RX Margin Analysis Ports ------------------------
.gt0_eyescandataerror_out (gt0_eyescandataerror_i),
.gt0_eyescantrigger_in (tied_to_ground_i),
//----------------------- Receive Ports - CDR Ports ------------------------
.gt0_rxcdrhold_in (gt0_rxcdrhold_i),
.gt0_rxcdrovrden_in (tied_to_ground_i),
//----------------- Receive Ports - Clock Correction Ports -----------------
.gt0_rxclkcorcnt_out (gt0_rxclkcorcnt_i),
//---------------- Receive Ports - FPGA RX interface Ports -----------------
.gt0_rxdata_out (gt0_rxdata_i),
//----------------- Receive Ports - Pattern Checker Ports ------------------
.gt0_rxprbserr_out (gt0_rxprbserr_i),
.gt0_rxprbssel_in (gt0_rxprbssel_i),
//----------------- Receive Ports - Pattern Checker ports ------------------
.gt0_rxprbscntreset_in (gt0_rxprbscntreset_i),
//---------------- Receive Ports - RX 8B/10B Decoder Ports -----------------
.gt0_rxdisperr_out (gt0_rxdisperr_i),
.gt0_rxnotintable_out (gt0_rxnotintable_i),
//------------------------- Receive Ports - RX AFE -------------------------
.gt0_gtxrxp_in (RXP_IN[0]),
//---------------------- Receive Ports - RX AFE Ports ----------------------
.gt0_gtxrxn_in (RXN_IN[0]),
//----------------- Receive Ports - RX Buffer Bypass Ports -----------------
.gt0_rxbufreset_in (gt0_rxbufreset_i),
.gt0_rxbufstatus_out (gt0_rxbufstatus_i),
//------------ Receive Ports - RX Byte and Word Alignment Ports ------------
.gt0_rxbyteisaligned_out (gt0_rxbyteisaligned_i),
.gt0_rxbyterealign_out (gt0_rxbyterealign_i),
.gt0_rxcommadet_out (gt0_rxcommadet_i),
.gt0_rxmcommaalignen_in (1'b1),
.gt0_rxpcommaalignen_in (1'b1),
//------------------- Receive Ports - RX Equalizer Ports -------------------
.gt0_rxdfelpmreset_in (tied_to_ground_i),
.gt0_rxmonitorout_out (gt0_rxmonitorout_i),
.gt0_rxmonitorsel_in (2'b00),
//------------- Receive Ports - RX Fabric Output Control Ports -------------
.gt0_rxoutclkfabric_out (gt0_rxoutclkfabric_i),
//----------- Receive Ports - RX Initialization and Reset Ports ------------
.gt0_gtrxreset_in (tied_to_ground_i),
.gt0_rxpcsreset_in (tied_to_ground_i),
.gt0_rxpmareset_in (gt0_rxpmareset_i),
//---------------- Receive Ports - RX Margin Analysis ports ----------------
.gt0_rxlpmen_in (gt0_rxlpmen_i),
//--------------- Receive Ports - RX Polarity Control Ports ----------------
.gt0_rxpolarity_in (gt0_rxpolarity_i),
//----------------- Receive Ports - RX8B/10B Decoder Ports -----------------
.gt0_rxchariscomma_out (gt0_rxchariscomma_i),
.gt0_rxcharisk_out (gt0_rxcharisk_i),
//------------ Receive Ports -RX Initialization and Reset Ports ------------
.gt0_rxresetdone_out (gt0_rxresetdone_i),
//---------------------- TX Configurable Driver Ports ----------------------
.gt0_txpostcursor_in (gt0_txpostcursor_i),
.gt0_txprecursor_in (gt0_txprecursor_i),
//------------------- TX Initialization and Reset Ports --------------------
.gt0_gttxreset_in (tied_to_ground_i),
.gt0_txuserrdy_in (tied_to_vcc_i),
//-------------- Transmit Ports - 8b10b Encoder Control Ports --------------
.gt0_txchardispmode_in (gt0_txchardispmode_i),
.gt0_txchardispval_in (gt0_txchardispval_i),
//---------------- Transmit Ports - Pattern Generator Ports ----------------
.gt0_txprbsforceerr_in (gt0_txprbsforceerr_i),
//-------------------- Transmit Ports - TX Buffer Ports --------------------
.gt0_txbufstatus_out (gt0_txbufstatus_i),
//------------- Transmit Ports - TX Configurable Driver Ports --------------
.gt0_txdiffctrl_in (gt0_txdiffctrl_i),
.gt0_txmaincursor_in (7'b0000000),
//---------------- Transmit Ports - TX Data Path interface -----------------
.gt0_txdata_in (gt0_txdata_i),
//-------------- Transmit Ports - TX Driver and OOB signaling --------------
.gt0_gtxtxn_out (TXN_OUT[0]),
.gt0_gtxtxp_out (TXP_OUT[0]),
//--------- Transmit Ports - TX Fabric Clock Output Control Ports ----------
.gt0_txoutclkfabric_out (gt0_txoutclkfabric_i),
.gt0_txoutclkpcs_out (gt0_txoutclkpcs_i),
//------------------- Transmit Ports - TX Gearbox Ports --------------------
.gt0_txcharisk_in (gt0_txcharisk_i),
//----------- Transmit Ports - TX Initialization and Reset Ports -----------
.gt0_txpcsreset_in (tied_to_ground_i),
.gt0_txpmareset_in (tied_to_ground_i),
.gt0_txresetdone_out (gt0_txresetdone_i),
//--------------- Transmit Ports - TX Polarity Control Ports ---------------
.gt0_txpolarity_in (gt0_txpolarity_i),
//---------------- Transmit Ports - pattern Generator Ports ----------------
.gt0_txprbssel_in (gt0_txprbssel_i),
//_____________________________________________________________________
//_____________________________________________________________________
//GT1 (X1Y3)
//-------------------------- Channel - DRP Ports --------------------------
.gt1_drpaddr_in (gt1_drpaddr_i),
.gt1_drpdi_in (gt1_drpdi_i),
.gt1_drpdo_out (gt1_drpdo_i),
.gt1_drpen_in (gt1_drpen_i),
.gt1_drprdy_out (gt1_drprdy_i),
.gt1_drpwe_in (gt1_drpwe_i),
//------------------------- Digital Monitor Ports --------------------------
.gt1_dmonitorout_out (gt1_dmonitorout_i),
//----------------------------- Loopback Ports -----------------------------
.gt1_loopback_in (gt1_loopback_i),
//---------------------------- Power-Down Ports ----------------------------
.gt1_rxpd_in (gt1_rxpd_i),
.gt1_txpd_in (gt1_txpd_i),
//------------------- RX Initialization and Reset Ports --------------------
.gt1_eyescanreset_in (tied_to_ground_i),
.gt1_rxuserrdy_in (tied_to_vcc_i),
//------------------------ RX Margin Analysis Ports ------------------------
.gt1_eyescandataerror_out (gt1_eyescandataerror_i),
.gt1_eyescantrigger_in (tied_to_ground_i),
//----------------------- Receive Ports - CDR Ports ------------------------
.gt1_rxcdrhold_in (gt1_rxcdrhold_i),
.gt1_rxcdrovrden_in (tied_to_ground_i),
//----------------- Receive Ports - Clock Correction Ports -----------------
.gt1_rxclkcorcnt_out (gt1_rxclkcorcnt_i),
//---------------- Receive Ports - FPGA RX interface Ports -----------------
.gt1_rxdata_out (gt1_rxdata_i),
//----------------- Receive Ports - Pattern Checker Ports ------------------
.gt1_rxprbserr_out (gt1_rxprbserr_i),
.gt1_rxprbssel_in (gt1_rxprbssel_i),
//----------------- Receive Ports - Pattern Checker ports ------------------
.gt1_rxprbscntreset_in (gt1_rxprbscntreset_i),
//---------------- Receive Ports - RX 8B/10B Decoder Ports -----------------
.gt1_rxdisperr_out (gt1_rxdisperr_i),
.gt1_rxnotintable_out (gt1_rxnotintable_i),
//------------------------- Receive Ports - RX AFE -------------------------
.gt1_gtxrxp_in (RXP_IN[1]),
//---------------------- Receive Ports - RX AFE Ports ----------------------
.gt1_gtxrxn_in (RXN_IN[1]),
//----------------- Receive Ports - RX Buffer Bypass Ports -----------------
.gt1_rxbufreset_in (gt1_rxbufreset_i),
.gt1_rxbufstatus_out (gt1_rxbufstatus_i),
//------------ Receive Ports - RX Byte and Word Alignment Ports ------------
.gt1_rxbyteisaligned_out (gt1_rxbyteisaligned_i),
.gt1_rxbyterealign_out (gt1_rxbyterealign_i),
.gt1_rxcommadet_out (gt1_rxcommadet_i),
.gt1_rxmcommaalignen_in (1'b1),
.gt1_rxpcommaalignen_in (1'b1),
//------------------- Receive Ports - RX Equalizer Ports -------------------
.gt1_rxdfelpmreset_in (tied_to_ground_i),
.gt1_rxmonitorout_out (gt1_rxmonitorout_i),
.gt1_rxmonitorsel_in (2'b00),
//------------- Receive Ports - RX Fabric Output Control Ports -------------
.gt1_rxoutclkfabric_out (gt1_rxoutclkfabric_i),
//----------- Receive Ports - RX Initialization and Reset Ports ------------
.gt1_gtrxreset_in (tied_to_ground_i),
.gt1_rxpcsreset_in (tied_to_ground_i),
.gt1_rxpmareset_in (gt1_rxpmareset_i),
//---------------- Receive Ports - RX Margin Analysis ports ----------------
.gt1_rxlpmen_in (gt1_rxlpmen_i),
//--------------- Receive Ports - RX Polarity Control Ports ----------------
.gt1_rxpolarity_in (gt1_rxpolarity_i),
//----------------- Receive Ports - RX8B/10B Decoder Ports -----------------
.gt1_rxchariscomma_out (gt1_rxchariscomma_i),
.gt1_rxcharisk_out (gt1_rxcharisk_i),
//------------ Receive Ports -RX Initialization and Reset Ports ------------
.gt1_rxresetdone_out (gt1_rxresetdone_i),
//---------------------- TX Configurable Driver Ports ----------------------
.gt1_txpostcursor_in (gt1_txpostcursor_i),
.gt1_txprecursor_in (gt1_txprecursor_i),
//------------------- TX Initialization and Reset Ports --------------------
.gt1_gttxreset_in (tied_to_ground_i),
.gt1_txuserrdy_in (tied_to_vcc_i),
//-------------- Transmit Ports - 8b10b Encoder Control Ports --------------
.gt1_txchardispmode_in (gt1_txchardispmode_i),
.gt1_txchardispval_in (gt1_txchardispval_i),
//---------------- Transmit Ports - Pattern Generator Ports ----------------
.gt1_txprbsforceerr_in (gt1_txprbsforceerr_i),
//-------------------- Transmit Ports - TX Buffer Ports --------------------
.gt1_txbufstatus_out (gt1_txbufstatus_i),
//------------- Transmit Ports - TX Configurable Driver Ports --------------
.gt1_txdiffctrl_in (gt1_txdiffctrl_i),
.gt1_txmaincursor_in (7'b0000000),
//---------------- Transmit Ports - TX Data Path interface -----------------
.gt1_txdata_in (gt1_txdata_i),
//-------------- Transmit Ports - TX Driver and OOB signaling --------------
.gt1_gtxtxn_out (TXN_OUT[1]),
.gt1_gtxtxp_out (TXP_OUT[1]),
//--------- Transmit Ports - TX Fabric Clock Output Control Ports ----------
.gt1_txoutclkfabric_out (gt1_txoutclkfabric_i),
.gt1_txoutclkpcs_out (gt1_txoutclkpcs_i),
//------------------- Transmit Ports - TX Gearbox Ports --------------------
.gt1_txcharisk_in (gt1_txcharisk_i),
//----------- Transmit Ports - TX Initialization and Reset Ports -----------
.gt1_txpcsreset_in (tied_to_ground_i),
.gt1_txpmareset_in (tied_to_ground_i),
.gt1_txresetdone_out (gt1_txresetdone_i),
//--------------- Transmit Ports - TX Polarity Control Ports ---------------
.gt1_txpolarity_in (gt1_txpolarity_i),
//---------------- Transmit Ports - pattern Generator Ports ----------------
.gt1_txprbssel_in (gt1_txprbssel_i),
//____________________________COMMON PORTS________________________________
.gt0_qplllock_out(),
.gt0_qpllrefclklost_out(),
.gt0_qplloutclk_out(),
.gt0_qplloutrefclk_out(),
.sysclk_in(drpclk_in_i)
);
always @(posedge gt0_rxusrclk2_i or negedge gt0_rxresetdone_i)
begin
if (!gt0_rxresetdone_i)
begin
gt0_rxresetdone_r <= `DLY 1'b0;
gt0_rxresetdone_r2 <= `DLY 1'b0;
gt0_rxresetdone_r3 <= `DLY 1'b0;
end
else
begin
gt0_rxresetdone_r <= `DLY gt0_rxresetdone_i;
gt0_rxresetdone_r2 <= `DLY gt0_rxresetdone_r;
gt0_rxresetdone_r3 <= `DLY gt0_rxresetdone_r2;
end
end
always @(posedge gt0_txusrclk2_i or negedge gt0_txfsmresetdone_i)
begin
if (!gt0_txfsmresetdone_i)
begin
gt0_txfsmresetdone_r <= `DLY 1'b0;
gt0_txfsmresetdone_r2 <= `DLY 1'b0;
end
else
begin
gt0_txfsmresetdone_r <= `DLY gt0_txfsmresetdone_i;
gt0_txfsmresetdone_r2 <= `DLY gt0_txfsmresetdone_r;
end
end
always @(posedge gt1_rxusrclk2_i or negedge gt1_rxresetdone_i)
begin
if (!gt1_rxresetdone_i)
begin
gt1_rxresetdone_r <= `DLY 1'b0;
gt1_rxresetdone_r2 <= `DLY 1'b0;
gt1_rxresetdone_r3 <= `DLY 1'b0;
end
else
begin
gt1_rxresetdone_r <= `DLY gt1_rxresetdone_i;
gt1_rxresetdone_r2 <= `DLY gt1_rxresetdone_r;
gt1_rxresetdone_r3 <= `DLY gt1_rxresetdone_r2;
end
end
always @(posedge gt1_txusrclk2_i or negedge gt1_txfsmresetdone_i)
begin
if (!gt1_txfsmresetdone_i)
begin
gt1_txfsmresetdone_r <= `DLY 1'b0;
gt1_txfsmresetdone_r2 <= `DLY 1'b0;
end
else
begin
gt1_txfsmresetdone_r <= `DLY gt1_txfsmresetdone_i;
gt1_txfsmresetdone_r2 <= `DLY gt1_txfsmresetdone_r;
end
end
//------------ optional Ports assignments --------------
assign gt0_rxprbscntreset_i = tied_to_ground_i;
assign gt0_rxprbssel_i = 0;
assign gt0_loopback_i = 0;
assign gt0_txdiffctrl_i = 0;
assign gt0_rxbufreset_i = tied_to_ground_i;
assign gt0_rxcdrhold_i = tied_to_ground_i;
//------GTH/GTP
assign gt0_rxdfelpmreset_i = tied_to_ground_i;
assign gt0_rxpmareset_i = tied_to_ground_i;
assign gt0_rxpolarity_i = tied_to_ground_i;
assign gt0_rxpd_i = 0;
assign gt0_txprecursor_i = 0;
assign gt0_txpostcursor_i = 0;
assign gt0_txchardispmode_i = 0;
assign gt0_txchardispval_i = 0;
assign gt0_txpolarity_i = tied_to_ground_i;
assign gt0_txpd_i = 0;
assign gt0_txprbsforceerr_i = tied_to_ground_i;
assign gt0_txprbssel_i = 0;
assign gt1_rxprbscntreset_i = tied_to_ground_i;
assign gt1_rxprbssel_i = 0;
assign gt1_loopback_i = 0;
assign gt1_txdiffctrl_i = 0;
assign gt1_rxbufreset_i = tied_to_ground_i;
assign gt1_rxcdrhold_i = tied_to_ground_i;
//------GTH/GTP
assign gt1_rxdfelpmreset_i = tied_to_ground_i;
assign gt1_rxpmareset_i = tied_to_ground_i;
assign gt1_rxpolarity_i = tied_to_ground_i;
assign gt1_rxpd_i = 0;
assign gt1_txprecursor_i = 0;
assign gt1_txpostcursor_i = 0;
assign gt1_txchardispmode_i = 0;
assign gt1_txchardispval_i = 0;
assign gt1_txpolarity_i = tied_to_ground_i;
assign gt1_txpd_i = 0;
assign gt1_txprbsforceerr_i = tied_to_ground_i;
assign gt1_txprbssel_i = 0;
assign gt0_drpaddr_i = 9'd0;
assign gt0_drpdi_i = 16'd0;
assign gt0_drpen_i = 1'b0;
assign gt0_drpwe_i = 1'b0;
assign gt1_drpaddr_i = 9'd0;
assign gt1_drpdi_i = 16'd0;
assign gt1_drpen_i = 1'b0;
assign gt1_drpwe_i = 1'b0;
assign soft_reset_i = tied_to_ground_i;
endmodule
可以对照官方源码，看看去掉了哪些添加了哪些，不懂的可以找我问问~~
4.GTX收发数据编解码讲解
下一步就是添加自定义代码了，需要添加如下代码模块：
数据对齐模块；
数据编码模块；
数据解码模块；
数据编码模块和GTX的应用部分如下：
视频数据经过数据编码模块，变为有固定格式的数据帧，同时伴随着控制信号；
数据帧格式如下：(可自定义)
parameter VS_START_0 = 32'h55_00_00_bc, //发送场同步开始帧头0
parameter VS_START_1 = 32'h55_00_01_bc, //发送场同步开始帧头0
parameter UNUSE_DATA_0 = 32'h55_00_02_bc, //发送无效数据0
parameter UNUSE_DATA_1 = 32'h55_00_03_bc, //发送无效数据1
parameter OK_DATA_START = 32'h55_00_04_bc, //发送有效数据开始
parameter OK_DATA_END = 32'h55_00_05_bc, //发送有效数据结束
parameter VS_END_0 = 32'h55_00_06_bc, //发送场同步结束帧尾0
parameter VS_END_1 = 32'h55_00_07_bc, //发送场同步结束帧尾1
视频数据进来时是以hs、vs、de和rgb的格式，但GTX不管你这些，他发出去的数据是高速串行的差分信号，所以数据在进入GTX之前必须做如下处理：
1、24位的rgb数据先转为16位，再由16位转为32位；因为GTX的发送入口时32位；
2、将视频数据的vs、de和rgb处理为32位的并行数据，准备送入GTX的发送接口；
3、使用1个fifo实现16位转为32位；
利用上面的帧格式，就可以是原始的视频数据变为32位的并行数据了，
具体怎么实现的，粘贴一段状态机中的代码应该就由眉目了：
case(state)
frame_sys0:begin //发送帧同步信号55_00_00_bc
state <= frame_sys1;
coded_data <= VS_START_0;
coded_ctr <= 4'b0001;
end
frame_sys1:begin //发送帧同步信号55_00_01_bc
state <= unuse_data0;
coded_data <= VS_START_1;
coded_ctr <= 4'b0001;
end
unuse_data0:begin //发送无用的信号55_00_02_bc
state <= unuse_data1;
coded_data <= UNUSE_DATA_0;
coded_ctr <= 4'b0001;
end
unuse_data1:begin //发送无用的信号55_00_03_bc
if(coded_data_count >= FIFO_VTH_SET) state <= h_data_begin; //当FIFO 中有一行数据
else begin
state <= unuse_data0;
coded_data<= UNUSE_DATA_1;
end
end
也就是说：将vs的上下沿转化为了控制帧；同时伴随着4位的coded_ctr；由于代码太长，这里不方便全部给出，需要源码的兄弟可以找我；
数据编码模块和GTX的应用部分如下：
这部分是整个工程的重点：
GTX串并转换后得到32位的并行数据，但这个数据经过5.94G的高速传输后有可能出现数据错位的情况，这时数据对齐模块的作用就来了；
本模块将gtx接收后的数据利用k码进行对齐，通过逻辑分析仪抓取调试过程中，有时候会出现，发送的32位数据可能出现16位数据移位，也就是上一个32位的数据低16位可能和下一个32位数据的高16位拼接在一起，我们如何知道我们发出的数据，通过光纤传输接收后进行了错位，此时就轮到K码大显威力了，当我们接收的数据错位时，K码也会错位，此前我们发送的0001 ，可能会变为0100，然后我们根据这个0100来把接收到的数据重新组合，就可以得到正确的结果；
下面给出该部分的核心代码：
always@(posedge rx_clk or negedge rst_n) begin
if(!rst_n) rx_data_align <= 32'd0;
else begin
case(align_bit)
4'b0001: rx_data_align <= rx_data;//没错位直接赋值
4'b0100: rx_data_align <= {
rx_data[15:0],rx_data_r[31:16]};//错位进行拼接
default: rx_data_align <= 32'd0;
endcase
end
end
数据解码：
这部分的所用是根据之前的数据帧格式，还原出32位并行数据的vs、de和rgb888数据，相当于是数据编码的反向过程；同理，也需要一个fifo做数据位宽转换；
5.工程1介绍：OV5640转GTX
开发板：Kintex7开发板；
开发环境：vivado2019.1；
输入：OV5640，720P，RGB888视频格式；
输出：HDMI输出，720P；
工程BD如下：
工程代码架构如下：
6.工程2介绍：HDMI转GTX
开发板：Kintex7开发板；
开发环境：vivado2019.1；
输入：HDMI输入，1080P，RGB888视频格式；
输出：HDMI输出，1080P；
工程BD如下：
工程代码架构如下：
7.上板调试
OV5640输出结果：
8.福利领取
福利：工程代码的获取
代码太大，无法邮箱发送，以某度网盘链接方式发送，
资料获取方式：私，或者文章末尾的V名片。
网盘资料如下：
