Use Microsoft iSCSI Software Target on Windows Server 2008 R2 build iSCSI target
standard server, Windows 10 uses an iSCSI initiator to connect to the iSCSI storage
** Microsoft iSCSI Software Target 3.3 can be installed on Windows Server 2008 R2 server operating system, it is recommended to install Windows Server 2008 R2 virtual machine
1, install the iSCSI Software Target in the Microsoft
(1) Windows Server 2008 R2 to configure the IP address 192.168.169.133.
(2) Click iSCSI Software Target (x64), begin the installation(3) all of the installation process to select Next, until the installation is completed.
2. Create iSCSI Software Target
(1) Open the Control Panel, Administrative Tools in the Microsoft iSCSI Software Target, the iSCSI target, right click and choose "Create iSCSI Target"
(2) named iSCSI target
(3) set up the iSCSI initiator, you can connect to the iSCSI target, you can fill out the iSCSI initiator IQN identifier or use the DNS address, IP address and MAC address. Here the IP address of the iSCSI Initiator.（4）点击高级，添加，在标识符类型处选择 IP 地址，填写 iSCSI 发起程序所在 PC 的 IP 地址。完成 iSCSI 目标的 创建。
注意：此IP为VMnet8的IPv4地址（如果你的虚拟机上网方式为VMnet1，就填写VMnet1的IPv4地址）
（5）创建虚拟磁盘：在设备中，右键选择创建虚拟磁盘
（6）输入 iSCSI 虚拟磁盘的完整路径，在这里 VD1.vhd 为需要创建的 iSCSI 虚拟磁盘文件
（7）设置 iSCSI 虚拟磁盘的容量，此处设置为15GB。注意：目标目录中会创建出一个 15GB 的虚拟磁盘文件，请确认目标盘符的可用空间是否足够
（8）输入虚拟磁盘描述
（9）设置可以访问此虚拟磁盘的 iSCSI 目标：点击添加，选择之前创建的 iSCSI 目标
（10）以下为创建好的虚拟磁盘
3、连接 iSCSI 网络存储
（1）在 Windows 10操作系统中，打开控制面板，管理工具， iSCSI 发起程序，点击“是”启动 iSCSI 服务。
（2）切换到“发现”标签，点击“发现门户”，输入 Windows Server 2008 R2 服务器的 IP 地址 192.168.169.133（第一张图中的IP地址）
3）切换到“目标”标签，可以看到 iSCSI 目标的 IQN。如果看不到，请点击“刷新
(4) Select 2008 R2 iSCSI IQN Windows Server destination server, click the link, cancel "this connection Add to Favorites target list" (If you select "Add this to the list of favorite destinations connected", the Windows10 each boot, will automatically connect to the iSCSI target. in the experimental environment, need not do so.)
state (5) of the iSCSI target is connected
(6) to open the control panel management tools, computer management, disk management to the switching, prompts the new disk must be initialized, the 15GB disk 2 is located in the Windows Server iSCSI target 2008 R2. Select the disk partition style MBR (master boot record), click OK.
(7) can be carried out for the disk partition, format and other operations, and access the Explorer, and operation of the local hard drive.
The created partition on the hard disk iSCSI (8) G is a disk.
(9) operating on the iSCSI hard disk partition as a local hard drive.
4, delete the iSCSI network storage
above steps backward step by step can be deleted! ! !
