First of all, the first step will be to install our mobile phone-data cable-brush machine package.
1. Prepare our flashing package, as shown in the picture:
2 Unlock the BL lock before flashing, and there will be a detailed tutorial under "How to unlock BL in Xiaomi" on Baidu. Not much to say here.
After unlocking, we open the Mi 6 flashing tool, as shown in the picture:
First, flash into one of our packages "Mi 6 official package" After completing the steps in the picture, click on the flashing tool, and wait for it to turn green.
After the official package is flashed, we will shut it down directly after it is turned on, press and hold the volume down and power off keys at the same time to enter "FASTBOOT mode", plug in the data cable, and we will flash into "recovery"
Then we open the Mi 6 flashing tool as shown in the figure:
After following the steps, the phone will automatically restart, and then restart to enter the twrp interface. Let's double-clear first, first click on Advanced Clear, check the first five, then slide, return to click Format DATA after completion, and enter "yes". After double clearing, you will go to the main interface of twrp, click restart, restart recovery.
After restarting, we connect the data cable to the mobile phone, drag the virtual package to the built-in storage of the mobile phone, and click Install.
As shown in the picture:
After brushing the virtual package, you must turn it on. After booting and entering the Lineage OS native system normally, the interface is very different from the Xiaomi system, and you can tell it at a glance!
After it can be turned on, we turn it off, turn it off, press the volume up button, and enter the recovery interface, which is the twrp interface. At this time, we will add the
three supplementary packages that were flashed into the folder and send them to Xiaomi. 6 In the mobile phone, there are two ways to copy, one is to directly
send it to the mobile phone in the recovery mode interface, and the other is to slide down the status bar to find the usb connection and click on the side of the usb connection when starting up, so
that you can start In the same state, it is copied into the mobile phone, and the same process is followed by putting the video into the mobile phone.
After copying the three flashing packages of 1.2.3 in the supplementary flash folder , we click Install, flash these three supplementary packs in the installation interface, first flash 1.zip and pay attention after flashing! Do not restart the system here
, return to the return icon in the lower right corner of the mobile phone, continue to click to enter the installation interface, flash 2, return to the same operation after flashing 2, and continue to flash 3 until the three supplementary packages are
flashed, and then restart the system.
After booting, we scroll up, first find edxp and click in, if everything follows the tutorial, you can see the activation status inside, at this time
we click the upper left corner and then click the module, check all the options, and then Go back to the desktop and swipe, find the virtual live broadcast app and click to enter, see
the activation interface, and authorize him to access the photo album and file access.
6. The last step is to activate. Enter *#06# in the place where you make a call on your mobile phone to find out the unique identification serial code of your mobile phone. There are two dual-card Mi 6s. Just copy the first serial code and send it to me for activation. The activation
here It is permanently activated offline, and can be used without networking!
7. After we send and copy the video to the mobile phone, select the video in the selection video. If the video is too large and flashes back, then wait for him to jump back and don’t move
anything. This is the literal meaning. When you encounter this In this case, operate like this. After jumping back to the selection interface, turn on the local camera, switch the scan code
interface, and switch the icon interface of the photo, you can see the display effect. If there is no effect, remember to operate it a few times. Check whether each step is
in place
8. You can manually play the video. The video folder of the mobile phone is the selected video. If there is only one video 1.MP4, it will automatically play a video in a loop. If you want to play
multiple videos in a loop, you can name the text in sequence in the video folder and Put videos in order, such as 1.MP4 2.MP4 3.MP4
, so that multiple videos can be played in a loop in order. Please test the specific supported project platforms by yourself.
The test chart is as follows:
