IEC/PAS 62722-2-1 specifies the performance requirements and test methods and conditions for lamps; it applies to ordinary LED lighting lamps claiming working performance;
IEC/PAS 62722-2-1 tests are as follows:
1. Luminous flux: the The initial luminous flux should not be less than 90% of the rated light output;
2. Light intensity distribution, peak light intensity and beam angle:
A: The light intensity distribution should be as claimed by the manufacturer,
B: When the peak light intensity is provided by the manufacturer or the responsible seller , the initial peak light intensity of LED lamps should not be lower than 75% of the rated light intensity;
C: When the beam angle value is provided by the manufacturer or the responsible seller, the beam angle of the LED lamps should not deviate more than 25% of the rated value;
3 Lamps Efficiency: The regulations in IEC/PAS62717 apply to all LED lamps. The efficacy of the lamp should be calculated by dividing the measured luminous flux by the measured input power. The efficiency of the lamp should not be less than 90% of the efficiency of the lamp;
4. Color coordinates: corresponding The initial and 6000-hour color coordinate values should not exceed the rated color change range;
5. Correlated color temperature: The measured correlated color temperature should not exceed the value specified by the manufacturer or the responsible seller;
6. Color rendering index: For a sample of For all tested samples, the decrease in the measured color rendering index should not be greater than: 3 points of the rated CRI value for the initial CRI value; 4 points of the rated CRI value for the CRI maintenance value at 2000H test;
7. Lumen maintenance : The test time can be reduced from 6000 hours to 2000 hours if appropriate component reliability data is available:
8. Endurance test:
a: temperature cycle test
b: power supply voltage switch test: under test voltage, current or power, the module It should be connected and short-opened for 30s each.
c: Accelerated working life test!
Jordan IEC62722, Jordan LED lamp performance test report, Jordan IEC62722 performance report, Jordan EN62722 performance report.
LED lamps IEC62722, LED high bay lamps IEC62722, ELD bulb lamps IEC62722, LED filament lamps IEC62722, LED
down lamps 2 Optical properties 040902 Luminaire performance - Part 2-1: Performance requirements for LED lamps
IEC 62722-2-1: 2014
EN 62722 -2-1: 2014 8
3 Color coordinates, color temperature,
color rendering index 040902 Luminaire performance - Part 2-1: Performance requirements for LED luminaires
IEC 62722-2-1: 2014
EN 62722-2-1: 2014 9
4 Lifetime 040902 Luminaire performance - Part 2-1: Performance requirements for LED luminaires
IEC 62722-2-1: 2014
EN 62722-2-1: 2014 10
1 Mark 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 4
2 Size 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 5
3 Input 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 7
4 Light output 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 8
5 Color coordinates, color temperature,
color rendering index 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 9
6 Lifetime 040908 Common Performance Requirements for LED Modules for Lighting
IEC 62717:2015
EN 62717:2015 10
1 Energy Efficiency Requirements 040904 Energy Efficiency, Functionality and Labeling Requirements for Lighting Products
Part 1
SASO-2870: 2015 4.1
2 Functionality
Requirements 040904 Energy Efficiency, Functionality for Lighting Products and Labeling Requirements
Part 1
SASO-2870: 2015 4.2
3 Labeling Requirements 040904 Energy Efficiency, Functionality and Labeling Requirements for Lighting Products
Part 1
SASO-2870: 2015 4.3
IEC/PAS 62722-2-1 tests are as follows:
1. Luminous flux: the The initial luminous flux should not be less than 90% of the rated light output;
2. Light intensity distribution, peak light intensity and beam angle:
A: The light intensity distribution should be as claimed by the manufacturer,
B: When the peak light intensity is provided by the manufacturer or the responsible seller , the initial peak light intensity of LED lamps should not be lower than 75% of the rated light intensity;
C: When the beam angle value is provided by the manufacturer or the responsible seller, the beam angle of the LED lamps should not deviate more than 25% of the rated value;
3 Lamps Efficiency: The regulations in IEC/PAS62717 apply to all LED lamps. The efficacy of the lamp should be calculated by dividing the measured luminous flux by the measured input power. The efficiency of the lamp should not be less than 90% of the efficiency of the lamp;
4. Color coordinates: corresponding The initial and 6000-hour color coordinate values should not exceed the rated color change range;
5. Correlated color temperature: The measured correlated color temperature should not exceed the value specified by the manufacturer or the responsible seller;
6. Color rendering index: For a sample of For all tested samples, the decrease in the measured color rendering index should not be greater than: 3 points of the rated CRI value for the initial CRI value; 4 points of the rated CRI value for the CRI maintenance value at 2000H test;
7. Lumen maintenance : The test time can be reduced from 6000 hours to 2000 hours if appropriate component reliability data is available:
8. Endurance test:
a: temperature cycle test
b: power supply voltage switch test: under test voltage, current or power, the module It should be connected and short-opened for 30s each.
c: Accelerated working life test!
Jordan IEC62722, Jordan LED lamp performance test report, Jordan IEC62722 performance report, Jordan EN62722 performance report.
LED lamps IEC62722, LED high bay lamps IEC62722, ELD bulb lamps IEC62722, LED filament lamps IEC62722, LED
down lamps 2 Optical properties 040902 Luminaire performance - Part 2-1: Performance requirements for LED lamps
IEC 62722-2-1: 2014
EN 62722 -2-1: 2014 8
3 Color coordinates, color temperature,
color rendering index 040902 Luminaire performance - Part 2-1: Performance requirements for LED luminaires
IEC 62722-2-1: 2014
EN 62722-2-1: 2014 9
4 Lifetime 040902 Luminaire performance - Part 2-1: Performance requirements for LED luminaires
IEC 62722-2-1: 2014
EN 62722-2-1: 2014 10
1 Mark 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 4
2 Size 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 5
3 Input 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 7
4 Light output 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 8
5 Color coordinates, color temperature,
color rendering index 040908 Performance requirements for LED modules for general lighting
IEC 62717:2015
EN 62717:2015 9
6 Lifetime 040908 Common Performance Requirements for LED Modules for Lighting
IEC 62717:2015
EN 62717:2015 10
1 Energy Efficiency Requirements 040904 Energy Efficiency, Functionality and Labeling Requirements for Lighting Products
Part 1
SASO-2870: 2015 4.1
2 Functionality
Requirements 040904 Energy Efficiency, Functionality for Lighting Products and Labeling Requirements
Part 1
SASO-2870: 2015 4.2
3 Labeling Requirements 040904 Energy Efficiency, Functionality and Labeling Requirements for Lighting Products
Part 1
SASO-2870: 2015 4.3