Dynamic NAT Network Address Translation (practice)

Topology FIG.

---

---

Step 1: Configure switch SW

sw#conf t 
sw(config)#no ip routing        //关闭路由功能
sw(config)#int f1/0
sw(config-if)#speed 100         //配置速率  
sw(config-if)#dup full          //配置全双工模式

---

Step: configure the router R1, and sets NAT

1. Configure router routing arms

R1#conf t
R1(config)#int f0/0
R1(config-if)#ip add 192.168.100.1 255.255.255.0
R1(config-if)#no shut
R1(config-if)#int f0/1 
R1(config-if)#ip add 12.0.0.1 255.255.255.0
R1(config-if)#no shut
R1(config-if)#ex

---

2. Set the NAT address translation

R1(config)#access-list 1 permit 192.168.100.0 0.0.0.255         //设定内部地址转化范围
R1(config)#ip nat pool test 12.0.0.10 12.0.0.100 netmask 255.255.255.0          ////设定外部地址转化范围
R1(config)#ip nat inside source list 1 pool test            //调用ip地址池
R1(config)#int f0/0
R1(config-if)#ip nat inside                 //将NAT应用于内部端口
R1(config-if)#int f0/1
R1(config-if)#ip nat outside                //将NAT应用于外部端口
R1(config-if)#end 

---

Step Three: Configure the client ip address

PC1> ip 192.168.100.10 192.168.100.1
Checking for duplicate address...
PC1 : 192.168.100.10 255.255.255.0 gateway 192.168.100.1

PC2> ip 192.168.100.20 192.168.100.1 
Checking for duplicate address...
PC1 : 192.168.100.20 255.255.255.0 gateway 192.168.100.1

PC3> ip 12.0.0.12 12.0.0.1
Checking for duplicate address...
PC1 : 12.0.0.12 255.255.255.0 gateway 12.0.0.1

---

Step four: Test the whole network interoperability, and use the debug function

1. Test Interoperability

PC1> ping 12.0.0.12
84 bytes from 12.0.0.12 icmp_seq=1 ttl=63 time=31.244 ms
84 bytes from 12.0.0.12 icmp_seq=2 ttl=63 time=31.282 ms
84 bytes from 12.0.0.12 icmp_seq=3 ttl=63 time=46.897 ms
84 bytes from 12.0.0.12 icmp_seq=4 ttl=63 time=46.834 ms
84 bytes from 12.0.0.12 icmp_seq=5 ttl=63 time=31.210 ms

PC2> ping 12.0.0.12
84 bytes from 12.0.0.12 icmp_seq=1 ttl=63 time=46.864 ms
84 bytes from 12.0.0.12 icmp_seq=2 ttl=63 time=46.864 ms
84 bytes from 12.0.0.12 icmp_seq=3 ttl=63 time=31.242 ms
84 bytes from 12.0.0.12 icmp_seq=4 ttl=63 time=31.273 ms
84 bytes from 12.0.0.12 icmp_seq=5 ttl=63 time=31.208 ms

---

2.debug ability to view the address translation process

R1#debug ip nat
IP NAT debugging is on
R1#
*Mar  1 00:15:21.287: NAT*: s=192.168.100.10->12.0.0.10, d=12.0.0.12 [55463]
*Mar  1 00:15:21.295: NAT*: s=12.0.0.12, d=12.0.0.10->192.168.100.10 [55463]

//PC1 地址转换成功

R1#
*Mar  1 00:19:12.139: NAT*: s=192.168.100.20->12.0.0.11, d=12.0.0.12 [55693]
*Mar  1 00:19:12.159: NAT*: s=12.0.0.12, d=12.0.0.11->192.168.100.20 [55693]

//PC2 地址转换成功