table of Contents
1. acquaintance equipment
1.1 Appearance
Software Version 1.2
2. How to log in
When you first get the AC / SG device, you can log onto the device console in the following ways
SANGFOR AC / SG devices, each network port factory default IP address is: eth0 (LAN): 10.251.251.251/24, eth1 (DMZ) 10.252.252.252/24
1, using a crossover cable and computer equipment
(1) If the computer is connected to a port of the device eth0, need to configure a 10.251.251.0/24 network address (except 10.251.251.251) on the computer, to open the browser to input https://10.251.251.251 log gateway device console.
(2) If the computer is connected to a port of the device eth1, need to configure a 10.252.252.0/24 network address (except 10.252.252.252) on the computer, to open the browser to input https://10.252.252.252 log gateway device console.
2. Enter the admin account login console device. The default administrator username and password admin / admin.
If the device interface address is modified, without knowing the interface address changeUnder the circumstances, the following two methods to log in
1, lan port SANGFOR AC / SG device (eth0 defined as the default LAN) with a reserved IP address is 128.127.125.252/29, configure the computer's IP address 128.127.125.253/29, and devices connected to the computer eth0 oral cross lines, https://128.127.125.252 console by logging in gateways.
Meanwhile, AC / SG apparatus dmz port (defined as the default eth1 dmz) have reserved IP address 128.128.125.252/29, the device may also be connected to a computer via a crossover cable eth1 port and IP computer configured to 128.128.125.253/29, via https : //128.128.125.252 login console device.
注意：
1、路由模式部署时lan和dmz都有保留地址，网桥模式网桥br0和dmz 有保留地址，旁路模式部署时管理口有保留地址。
2、路由模式出厂默认eth0定义为lan，eth1口定义为dmz，如设备部署模式
Example: configuration is redefined network port, such as port defined as eth2 lan, defined as dmz eth0, eth2 case there lan port reserved port addresses, reserved port eth0 mouth dmz address; bypass mode and a deployed bridge network interface reserved addresses also follows this principle.
2, upgrade the system by SANGFOR tool after finding the device address, an address obtained by looking into the console equipment
(1) mounted SANGFOR upgrade system tools and devices that use a PC directly connected to cross-line
(2) installed on the PC firewall to close windows and from with a firewall, as in FIG.
(3) Find the device addresses SANGFOR system upgrade tool, as shown in FIG.
(4) found by SANGFOR upgrade system tools address Login device
3. How to restore factory settings
Restore factory settings cause the device to reboot.
In the case of the normal logging in, you can restore factory settings in two ways
1, configured through the console interface to restore the factory
restore factory defaults will reboot the device after factory configuration restored by this method, once again log into the console, the lower right corner there will be "successful recovery" prompt, as shown below.
2, restore the factory configuration tool to upgrade the system by SANGFOR
3, two cross-line short electrical equipment recovery ports
If login to the device (e.g., device interface address not available), the following methods may attempt to restore the factory configuration
(1) The first device is switched off.
(2) preparing an intersection line.
(3) using a crossover cable panel of any two devices on a set of non-bypasse electrical interface (eth0 and eth2 are bypasse e.g. mouth, can not shorting the two ports recovery password)
(4) applied to the device is powered on.
Wait until the device restarts (Description device to factory configuration is successful), then be sure to disconnect the crossover cable shorted electrical outlet.
(5) other equipment up to the factory by address, account number and password default console device
4. How Password Recovery Console
If you forget your admin password, making it impossible to log in, they need to keep device configuration (ie can not be restored factory configuration), you can restore the admin password solely by the following method.
1. Make sure your computer and devices can communicate, access the device address, HTTPS: //acip/php/rp.php, as shown below, suggesting that "create the file successfully, crossover cable connection and restart the device."
2, any cross-line preparation of two non-shorted devices set bypasse electrical interface (eth0 and eth2 are bypasse e.g. mouth, can not shorting the two ports recovery password)
3, manually restart the device, the restart process, observe the cross-line shorting two electrical ports ACT lamp state, the two lights blink ACT electrical interface 10 that the password recovery is complete at this time can be shorted to unplug cross-line, by default console account password admin / admin log in to the device. Reboot to password recovery success about about 3-5 minutes.
4, step 3 can not determine if password recovery is successful, you can always wait, wait about 5-10 minutes, according to the LAN light state attempts by default account admin / admin account to log in