From August 9th to 11th, the 2023 Automotive Testing and Quality Control Expo will be held in Hall 1 of the Shanghai World Expo Exhibition and Convention Center. This exhibition will showcase new developments in testing and verification technology in the fields of vehicle, component and system development, New products and new solutions. YiXing Technology will bring its latest ETH testing, smart driving testing, PPS testing and other solutions to the test exhibition. Welcome to visit booth No. 8051 .
Today Xiaoyi will introduce the upcoming eTM series products and give everyone a sneak peek!
ETS4640
100M Ethernet converter
ETS4640 is a vehicle-mounted Ethernet media conversion module that supports mutual conversion between 100BASE-T1 and 100BASE-TX interfaces to achieve normal communication between the vehicle-mounted Ethernet ECU and the PC.
Product Highlights
✔ Support Master/Slave mode configuration
✔Micro USB 5V power supply
✔ Plug and play, easy to operate
Application scenarios
ETS4640 is used as a media conversion device for the development or testing of automotive Ethernet ECUs to improve development and testing efficiency.
Technical Parameters
Operating Voltage |
5±0.5V DC |
Power supply |
Micro USB powered |
Number of channels |
1 |
Operating temperature |
0-50℃ |
Dimensions (length*width*height) |
83mm*50mm*20mm |
weight |
About 56g |
ETS4650
100M/1000M Ethernet converter
ETS4650 is a vehicle-mounted Ethernet interface conversion module that supports mutual conversion between 100/1000BASE-T1 and 100/1000BASE-T interfaces to achieve normal communication between the vehicle-mounted Ethernet ECU and PC.
Product Highlights
✔ 100M and 1000M rate self-adaptation
✔Master/Slave mode self-adaptation
✔ Link delay impact <2μs
✔ Plug and play, easy to operate
✔ The T1 interface adopts Roseberger vehicle Ethernet connector, which is safe and reliable
Application scenarios
ETS4650 is used as a media conversion device for the development or testing of automotive Ethernet ECUs to improve development and testing efficiency.
Technical Parameters
PHY chip |
MARVELL:88Q2112-A2 |
Operating Voltage |
4-18V DC |
Power supply |
Type-C power supply |
Working current |
5V power supply, 100M rate 280mA 5V power supply, 1000M rate 380mA |
Conversion delay |
100BASE-T1—100BASE-TX: about 2μs 1000BASE-T1—1000BASE-T: about 2μs |
Number of channels |
1 |
Operating temperature |
0-50℃ |
Dimensions (length*width*height) |
105mm*85mm*28.5mm |
weight |
About 150g |
ETS4660
MultiGBASE-T1 and MultiGBASE-T media conversion modules
ETS4660 is a vehicle-mounted Ethernet interface conversion module, mainly used to support the mutual conversion of 2.5/5/10GBASE-T1 and 2.5/5/10GBASE-T interfaces to achieve normal communication between the vehicle-mounted Ethernet ECU and the PC.
Product Highlights
✔ T1 interface adopts Rosenberger H-MTD standard connector
✔T interface adopts SFP+ standard interface
✔ Supports two power supply methods: 5V power supply and 7V-28V power supply
✔ Supports three communication rates of 2.5Gbps, 5Gbps and 10Gbps
✔ Plug and play, easy to operate
Product Features
● Supports mutual conversion between 2.5GBASE-T1 and 2.5GBASE-T interfaces
● Supports mutual conversion between 5GBASE-T1 and 5GBASE-T interfaces
● Supports mutual conversion between 10GBASE-T1 and 10GBASE-T interfaces
● Switching between Master/Slave and communication rate through DIP switch
●Type-C interface power supply (5V) or Phoenix interface power supply (7V-28V) PHY working status indicator light
ETS6201-BR/CR
Single channel Gigabit Ethernet fault injection module
ETS6201-BR/CR is a Gigabit Ethernet fault injection module. The module is controlled through CAN bus communication to realize the Ethernet fault injection function. It can support fault simulation of an independent 100/1000BASE-T1 interface and ECU operating voltage and current. monitor. (*ECU working voltage and current monitoring functions are only available in the CR version, but not in the BR basic version)
Product Highlights
✔Supports 1 100/1000BASE-T1 test channel
✔ Supports multiple fault injections: short circuit to power, short circuit to ground, PN short circuit, PN open circuit, etc.
✔ Support 1-way ECU power supply control
✔ ECU working voltage and current monitoring (this function is only available in the CR version)
✔ The module is controlled through the 500Kbps CAN interface and supports multi-module cascading
✔ Provide over-current protection and over-voltage protection
✔ Provide SDK for secondary development
Application scenarios
ETS6201 can be used for Ethernet physical layer and system testing to improve the automation of Ethernet testing. The connection diagram is as follows:
Technical Parameters
Operating Voltage |
12±1VDC |
Working current |
12V@500mA |
ECU power supply interface |
Support voltage 0-36V, current 0-10A |
Current monitoring range |
0-10A, accuracy ≤3% |
Program control method |
CAN |
Number of channels |
1 |
Operating temperature |
-20℃~85℃ |
Dimensions (length*width*height) |
149mm*145mm*53mm |
weight |
About 600g |
ETS6204-BR/CR
4-way Gigabit Ethernet fault injection module
ETS6204-BR/CR is a Gigabit Ethernet fault injection module. The module is controlled through CAN bus communication to realize the Ethernet fault injection function. It can support fault simulation of 4 independent 100/1000BASE-T1 interfaces and ECU operating voltage and current. monitor. (*ECU working voltage and current monitoring functions are only available in the CR version, but not in the BR basic version)
Product Highlights
✔ Support 4-channel 100/1000BASE-T1 test channels
✔ Supports multiple fault simulations: short circuit to power, short circuit to ground, PN short circuit, PN open circuit, etc.
✔ Support 1-way ECU power supply control
✔ ECU working voltage and current monitoring (this function is only available in the CR version)
✔ The module is controlled through the 500Kbps CAN interface and supports multi-module cascading
✔ Provide over-current protection and over-voltage protection
✔ Provide SDK for secondary development
Application scenarios
ETS6204 can be used for Ethernet physical layer and system testing to improve the automation of Ethernet testing. The connection diagram is as follows:
Technical Parameters
Operating Voltage |
12±1VDC |
Working current |
12V@500mA |
ECU power supply interface |
Support voltage 0-36V, current 0-10A |
Current monitoring range |
0-10A, accuracy ≤3% |
Program control method |
CAN |
Number of channels |
4 |
Operating temperature |
-20℃~85℃ |
Dimensions (length*width*height) |
219mm*145mm*53mm |
weight |
About 900g |
ETS6124-BR/CR
CAN/LIN fault injection module
ETS6124-BR/CR is a fault simulation module that implements ECU network fault injection and ECU power supply control in traditional network CAN/LIN test projects. It can also monitor the ECU operating voltage and current. (*ECU working voltage and current monitoring functions are only available in the CR version, but not in the BR basic version)
Product Highlights
✔ Provide 2 CAN or 4 LIN test channels
✔ Supports multiple fault injections: bus short circuit to power supply and ground, short circuit between buses, bus open circuit, etc.
✔ 2-way ECU power supply control
✔ ECU working voltage and current monitoring (this function is only available in the CR version)
✔ The module is controlled through the 500Kbps CAN interface and supports multi-module cascading
✔ Provide SDK for secondary development
Application scenarios
ETS6124-BR/CR solves the problems of complex wiring, excessive number of relays, high programming complexity, and poor scalability that occur when using network automated test systems for system-level testing. The connection block diagram is as follows:
Technical Parameters
Operating Voltage |
12±1VDC |
Working current |
12V@500mA |
ECU power supply interface |
Support voltage 0-36V, current 0-10A |
Current monitoring range |
0-10A, accuracy ≤3% |
Program control method |
CAN |
Number of channels |
The following channel configuration methods are supported: 2-way CAN 1 channel CAN, 2 channels LIN 4-way LIN |
Operating temperature |
-20℃~85℃ |
Dimensions (length*width*height) |
120mm*135mm*50mm |
weight |
About 433g |
…………………………………………………………………………………………………………………
EH6302
ECU power management board
EH6302 is an ECU power management board that supports 2 independent power on/off channels. It can measure the voltage and current values of each power supply in real time and upload them to the host computer through the CAN interface.
Product Highlights
✔ ECU monitoring voltage: 4-36V, accuracy 0.1V
✔ ECU monitoring current: 30μA-30A
✔ CAN communication interface, 500K rate, supports bus cascade
✔Supports channel opening and channel fault indicator lights, overcurrent protection, and overvoltage protection
Product Features
●Support 2 independent power supply on/off functions
● CAN communication interface, 500K rate, supports bus cascade
● Support board support light and power channel indicator light
●Support board relay fault diagnosis function
Technical Parameters
Board working voltage |
12V DC |
|
Board working current |
12V@500mA |
|
Voltage measurement range |
4-36VDC, accuracy 0.1V |
|
Current measurement range |
30μA-30A: Resolution: 5uA: Accuracy is as follows: |
|
30uA≤current range≤1mA |
±1.5% |
|
Current range≤10mA |
±1.5% |
|
Current range≤100mA |
±1% |
|
Current range≤1A |
±1% |
|
Current range≤10A |
±1% |
|
Current range≤30A |
±1% |
|
Voltage/current raw data acquisition frequency |
200Hz |
|
Operating temperature |
-40°C-85°C(no icing) |
|
size |
220*145*53mm(4U) |
|
weight |
About 700g |
Today’s introduction ends here~ Friends who are interested in our Yinxing products are welcome to come find Xiaoyi offline. We will arrange a dedicated person at our offline booth to communicate with you one-on-one!