From
PEmicro official website
for information:
1: BOOTUPDATEAPP with Bootloader v1.11 fixes Added Windows 8.1 Support;
2: MSD - DEBUG Version 1.14 adds Windows8.1 support system
- Added combined MSD, DEBUG and CDC virtual serial support in a single APP .
switching the BETWEEN MSD and DEBUG Apps iS NO longer Necessary
-. Added Windows 8.1 Support
OpenSDA firmware version rose 1.14
to MSD , DEBUG , CDC virtual serial ports into one (later use MSD or DEBUG no longer need to enter Bootloader switched) increase the Windows8.1 support system
detailed operation: a, installation
PE driver, enter PEmicro: http://www.pemicro.com/opensda/
Download PEDrivers_install.exe for manual install.
If you have installed:
Kinetis Design Studio installer for Microsoft Windows
or
Kinetis Design Studio installer for Linux 64-bit RPM 3.0.0,
you do not need to install the PE driver. It is strongly recommended to install the Kinetis suite.
2. Download the firmware Program, enter PEmicro: http://www.pemicro.com/opensda/
download Firmware Apps (.zip file). 3. After decompression, you can see the following icon: BOOTUPDATEAPP description, Bootloader upgrade package, OpenSDA description, version 1.14 The OpenSDA firmware program of each board of each board . Fourth, to update the Bootloader , please read the BOOTUPDATEAPP_release_notes and follow the steps below:
To update Bootloader please follow these steps:
1. Enter bootloader mode (generally by holding down the target reset button on the OpenSDA board and plugging in the USB connection).
2. Drag and drop the BOOTUPDATEAPP.SDA file to the root directory of the Bootloader "drive".
即OpenSDA_Bootloader_Update_App_v111_2013_12_11压缩包内的BOOTUPDATEAPP_Pemicro_v111.SDA
3. Unplug and replug your OpenSDA board to initiate Bootloader update. Bootloader update should take less than 15 seconds (probably averages 3 seconds).
4. Once update is complete, OpenSDA will automatically enumerate in Bootloader mode and green status LED will go on blinking with .5 second on/off intervals.
5. Run the SDA_INFO.HTM file in the root directory of the Bootloader "drive".
IMPORTANT: Please do not unplug OpenSDA while Bootloader is updating. You
can see from the webpage that the development board Bootloader has been upgraded to 1.11 (see the figure below)
5. Continue to update the Application Version:
Copy & paste or drag & drop the v 1.14 OpenSDA firmware applications (MSD-DEBUG-FRDM-KE02Z_Pemicro_v114.SDA ) into Bootloader disk / removable storage drive/ OpenSDA board;
6. Unplug and replug your OpenSDA board , It will appear as a removable storage drive with a volume label of FRDM-KE02Z. The Freedom Board is now updated to the latest firmware and application
(The status is justDeubg , can throw inside .srec file OpenSDA date)
seven, the Run at The SDA_INFO.HTM File in Directory at The root of at The Bootloader "Drive"
you can see from the web development board OpenSDA the Application Version has been upgraded to 1.14 (Refer to the figure below)
After completing the above steps, if you want to switch from OpenSDA 's debug and MSD modes, you no longer need to enter the Bootloader to choose between Debug or MSD firmware.
1: BOOTUPDATEAPP with Bootloader v1.11 fixes Added Windows 8.1 Support;
2: MSD - DEBUG Version 1.14 adds Windows8.1 support system
- Added combined MSD, DEBUG and CDC virtual serial support in a single APP .
switching the BETWEEN MSD and DEBUG Apps iS NO longer Necessary
-. Added Windows 8.1 Support
OpenSDA firmware version rose 1.14
to MSD , DEBUG , CDC virtual serial ports into one (later use MSD or DEBUG no longer need to enter Bootloader switched) increase the Windows8.1 support system
detailed operation: a, installation
PE driver, enter PEmicro: http://www.pemicro.com/opensda/
Download PEDrivers_install.exe for manual install.
If you have installed:
Kinetis Design Studio installer for Microsoft Windows
or
Kinetis Design Studio installer for Linux 64-bit RPM 3.0.0,
you do not need to install the PE driver. It is strongly recommended to install the Kinetis suite.
2. Download the firmware Program, enter PEmicro: http://www.pemicro.com/opensda/
download Firmware Apps (.zip file). 3. After decompression, you can see the following icon: BOOTUPDATEAPP description, Bootloader upgrade package, OpenSDA description, version 1.14 The OpenSDA firmware program of each board of each board . Fourth, to update the Bootloader , please read the BOOTUPDATEAPP_release_notes and follow the steps below:
To update Bootloader please follow these steps:
1. Enter bootloader mode (generally by holding down the target reset button on the OpenSDA board and plugging in the USB connection).
2. Drag and drop the BOOTUPDATEAPP.SDA file to the root directory of the Bootloader "drive".
即OpenSDA_Bootloader_Update_App_v111_2013_12_11压缩包内的BOOTUPDATEAPP_Pemicro_v111.SDA
3. Unplug and replug your OpenSDA board to initiate Bootloader update. Bootloader update should take less than 15 seconds (probably averages 3 seconds).
4. Once update is complete, OpenSDA will automatically enumerate in Bootloader mode and green status LED will go on blinking with .5 second on/off intervals.
5. Run the SDA_INFO.HTM file in the root directory of the Bootloader "drive".
IMPORTANT: Please do not unplug OpenSDA while Bootloader is updating. You
can see from the webpage that the development board Bootloader has been upgraded to 1.11 (see the figure below)
5. Continue to update the Application Version:
Copy & paste or drag & drop the v 1.14 OpenSDA firmware applications (MSD-DEBUG-FRDM-KE02Z_Pemicro_v114.SDA ) into Bootloader disk / removable storage drive/ OpenSDA board;
6. Unplug and replug your OpenSDA board , It will appear as a removable storage drive with a volume label of FRDM-KE02Z. The Freedom Board is now updated to the latest firmware and application
(The status is justDeubg , can throw inside .srec file OpenSDA date)
seven, the Run at The SDA_INFO.HTM File in Directory at The root of at The Bootloader "Drive"
you can see from the web development board OpenSDA the Application Version has been upgraded to 1.14 (Refer to the figure below)
After completing the above steps, if you want to switch from OpenSDA 's debug and MSD modes, you no longer need to enter the Bootloader to choose between Debug or MSD firmware.