1. The goal of the experiment
is to complete the backup and recovery of the win10 system in the win10 virtual system in the VMware virtual machine.
Second, the experimental steps to
complete this experiment we can be divided into the following steps:
1. Install VMware software 2. Create a virtual machine in VMware software and complete the installation of win10 system 3. Complete the system backup and recovery in virtual win10 system
3. The 
following interface appears after the downloaded VMware software is found during the experiment . Click Next 
to check I accept the license terms. Click Next 
to continue. Click Next 
to uncheck the following two options. 
Click Next to 
install. Click the license after completion, enter the activation code, activate the software, open the software after activation. 
Here we have installed VMware, let's proceed to the next step, create a new virtual machine and complete the installation of win10 system.
Click to create a new virtual machine, 
choose custom, 
choose next, 
choose to install the operating system later, 
we install the win10 system, choose the system, click next, and 
pay special attention here, it is best to choose to install in the solid state drive when choosing the installation location, In this way, the operation speed will be much improved. Name the name of the virtual machine. Click Next to 
select the firmware type. Click Next. 
Here is the number of processors for the virtual machine. Here, the author ’s computer is 4-core. 
This step of selecting memory will directly affect our post-virtualization. The running speed of the machine, please be careful not to exceed the memory of your real machine. The author's memory is 16G, choose 4G, 6G. 
Here we choose the network type. We choose NAT mode (special attention to these three modes: the bridge mode is directly used by the virtual machine. IP address of the machine to connect a network, the NAT IP address mode is to use a sub-device connection to connect real machine IP network, only the master mode can not connect to the network, only a LAN connection with the real machine) 
where the type of controller selected as required 
in accordance with It is required to select the disk type. 
Here you need to choose to create a new virtual disk 
. The size of the disk is virtual, you can make it according to your own needs. Note that you must choose to split the virtual disk into multiple files. 
The file name is directly jumped out here. We click Next. 
Here we choose custom hardware and operate the hardware 
here. Processor Virtualization must be checked. If not, the system may not be able to install 
the sound card and printer here. Because it is a virtual machine, there is no need to exist. We can remove it. A 
very important step. We use the ISO image file in the CD option. Ok, 
after setting up our system image , click Finish 
so we can see that a virtual machine is created
Next, we start to install the win10 operating system. Click to open the virtual machine. 
Pay special attention to this screen after opening the virtual machine. Press TAB quickly, otherwise you cannot install the system. 
Click next. 
Click to 
install the system installed here. According to the demand, we choose win10 professional Workstation Edition
I need to check I accept the license terms. 
Here we need to click Customize . Here we 
can see that we can assign disks. We choose New, the newly created disk locates the C drive, installs the system, and another disk locates the D drive. Customize, 
click OK to create the partition. 
Here, we need to format the D drive and 
install our win10 system in the C drive. Click Next. 
Here we can see that it is already installed, wait patiently and you can 
jump out of this interface after the installation is complete , you can restart 
the virtual machine screen after the restart, we chose China, and click Next 
select the keyboard layout, click Next 
here are some basic settings, then follow the prompts to complete
Here I do n’t want to create a Microsoft account, so I chose an offline account
Create your own computer name here, 
set your computer password, 
create your own secret security question, and 
follow the prompts
After accepting here, we can see that the win10 system has been preliminarily installed
Click here to open the personalized 
selection theme, desktop icon settings, check the desktop icons of 
commonly used computers, 
right-click on the virtual machine here, select to install VMware Tools, here is to install the driver
Follow the guidance, click Next, 
select the typical installation, 
click Install 
, and click Finish after installation. 
This will ask us to restart the system. Click Yes to restart and 
right-click on my computer. Select Properties to see the basic properties. Here we can see our windows. Not activated, we can buy a CDK on Taobao for activation (note your version), or you can choose online activation software for activation, but there are risks, which may cause viruses in the system. Here the author bought a CDK on Taobao for activation. Click on the device manager to see whether our driver is installed successfully, and an exclamation mark will be displayed if it is not successful!
Open the control panel, select the network, 
select the network and sharing center. 
Click here 
to see whether our virtual machine is connected to the network. If it is not connected, you can click the property to set it. 
Double-click to open the Internet protocol version 4 to 
set your own IP address
This method is troublesome. If you are bothered, you can open the virtual machine editor, click on the virtual network editor, and choose to assign the IP address to the virtual machine 
. If our win10 system has been successfully deployed, proceed to the next step. Backup and restore.
The system backup and restore need to use the micro PE tool, here I have installed the micro PE tool box in the U disk
We restart the system, press F12 on the opening page to enter the biso interface, select the U disk to enter
The following words will demonstrate two backup systems and recovery methods, one is to use backup software, this method is relatively simple, and the other is to use manual backup and restore.
First of all, we click on CGI backup and restore to
select the backup partition, we select the C drive, select the save path, click execute 
here and select restart, make sure 
you can see that there is already a backup here, wait patiently to 
complete, you can see the backup after the backup is completed Once the file has been 
opened, open the CGI software again, select the restore partition, select the restored C drive, the image file, and click execute to restore the system
note! Here the author has the following situation. After a study, it is found that the software version is low and it cannot be restored. You can download the latest CGI software online and put it in the micro PE tool to restore it. 
Below we introduce manual backup and restore system operations.
Click to run Ghost manually
Here Select OK 
here, according to pictures Select Backup system 
to select the hard disk backup partition where the 
C drive select backup 
here click also need to select the location to store the image file, select a good position on the list
below is selected compression: no compression, fast compression, high compression. Select fast compression, 
click YES to start compression, wait patiently to 
finish, you can see the image file, 
then restore the system backup, open Ghost, 
select the image file according to the method in the picture , select the restored partition, 
select the hard disk, 
select restore Partition, we are the C drive, 
click YES to restore
Just wait patiently for completion
Finally: installing the system on the real machine is actually the same as the virtual step. Press ESC when the computer starts (the author is an Asus notebook, according to the different keys of the respective computer) to enter the BISO interface, select the U disk, follow the steps Reinstall the system on the real machine and perform the system backup operation.