防火墙NAT Server实验

2.实验步骤

步骤 1 完成 USG6330-1 上、下行业务接口的配置。配置各接口 IP 地址并加入相应安全区域。

<USG> system-view

[USG6000V1]sysname USG6330-1

[USG6330-1] interface GigabitEthernet 1/0/1

[USG6330-1-GigabitEthernet1/0/1] ip address 10.1.2.1 255.255.255.0

[USG6330-1-GigabitEthernet1/0/1] quit

[USG6330-1] interface GigabitEthernet 1/0/4

[USG6330-1-GigabitEthernet1/0/4] ip address 40.1.1.1 255.255.255.0

[USG6330-1-GigabitEthernet1/0/4] quit

[USG6330-1] firewall zone trust

[USG6330-1-zone-trust] add interface GigabitEthernet 1/0/1

[USG6330-1-zone-trust] quit

[USG6330-1] firewall zone untrust

[USG6330-1-zone-untrust] add interface GigabitEthernet 1/0/4

[USG6330-1-zone-untrust] quit

步骤 2 配置域间包过滤策略。

[USG6330-1]security-policy

[USG6330-1-policy-security] rule name bidectinal_nat

[USG6330-1-policy-security-rule-policy_sec] source-zone untrust

[USG6330-1-policy-security-rule-policy_sec] destination-zone dmz

[USG6330-1-policy-security-rule-policy_sec] action permit

[USG6330-1-policy-security-rule-policy_sec] service ftp

[USG6330-1-policy-security-rule-policy_sec] quit

步骤 3 配置 NAT server。

[USG6330-1] nat server ftpserver protocol tcp global 40.1.1.2 ftp inside 10.1.1.100 ftp

[USG6330-1]nat address-group natpool2

[USG6330-1-address-group-natpool]section 10.1.1.10 10.1.1.20

步骤 5 在 DMZ 与 Untrust 域间应用 NAT ALG 功能，使服务器可以正常对外提供 FTP 服务。

[USG6330-1] firewall interzone dmz untrust

[USG6330-1 -interzone-dmz-untrust] detect ftp

[USG6330-1 -interzone-dmz-untrust] quit

步骤 6 创建 DMZ 区域和 Untrust 区域之间的 NAT 策略，确定进行 NAT 转换的源地址范围，并且将其与 NAT 地址池 2 进行绑定。

[USG6330-1]nat-policy

[USG6330-1-policy-nat]rule name biderectinal_nat

[USG6330-1-policy-nat-rule-source_nat]destination-zone dmz

[USG6330-1-policy-nat-rule-source_nat]source-zone untrust

[USG6330-1-policy-nat-rule-source_nat]source-address 40.1.1.0 24

[USG6330-1-policy-nat-rule-source_nat]action nat address-group natpool2

步骤 7 配置 Switch。

分别将两台 Switch 的三个接口加入同一个 VLAN，缺省即可。