Systemctl es una herramienta systemd principalmente responsable de controlar el sistema systemd y el administrador de servicios.
Systemd es una colección de daemons, herramientas y bibliotecas de administración de sistemas diseñados para reemplazar el proceso de inicio de System V. La función de Systemd es administrar y configurar centralmente sistemas similares a UNIX.
En el ecosistema de Linux, Systemd se implementa en la mayoría de las distribuciones estándar de Linux, solo unas pocas distribuciones aún no se implementan. Systemd suele ser el proceso principal de todos los demás demonios, pero no siempre.
Este artículo tiene como objetivo aclarar "cómo controlar sistemas y servicios" en sistemas que ejecutan systemd.
Primera experiencia de Systemd y conceptos básicos de Systemctl
1. Primero verifique si systemd está instalado en su sistema y determine la versión instalada actualmente
# systemctl --version
systemd 215
+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR
En el ejemplo anterior, está claro que tenemos instalada la versión 215 de systemd.
2. Verifique las ubicaciones de instalación de los binarios y bibliotecas de systemd y systemctl
# whereis systemd
systemd: /usr/lib/systemd /etc/systemd /usr/share/systemd /usr/share/man/man1/systemd.1.gz
# whereis systemctl
systemctl: /usr/bin/systemctl /usr/share/man/man1/systemctl.1.gz
3. Compruebe si systemd se está ejecutando
# ps -eaf | grep [s]ystemd
root 1 0 0 16:27 ? 00:00:00 /usr/lib/systemd/systemd --switched-root --system --deserialize 23
root 444 1 0 16:27 ? 00:00:00 /usr/lib/systemd/systemd-journald
root 469 1 0 16:27 ? 00:00:00 /usr/lib/systemd/systemd-udevd
root 555 1 0 16:27 ? 00:00:00 /usr/lib/systemd/systemd-logind
dbus 556 1 0 16:27 ? 00:00:00 /bin/dbus-daemon --system --address=systemd: --nofork --nopidfile --systemd-activation
Nota: systemd se ejecuta como un proceso principal (PID=1). En la salida del comando ps anterior con el parámetro (-e), selecciona todos los procesos, (-a) selecciona todos los procesos excepto el líder de la sesión y usa el parámetro (-f) para generar una lista de formato completo (es decir, -eaf).
También tenga en cuenta los corchetes finales en el ejemplo anterior y el resto del ejemplo. Las expresiones de paréntesis son parte de las expresiones de clase de caracteres de grep.
4. Analizar el proceso de inicio de systemd
# systemd-analyze
Startup finished in 487ms (kernel) + 2.776s (initrd) + 20.229s (userspace) = 23.493s
5. Analizar el tiempo empleado por cada proceso al inicio
# systemd-analyze blame
8.565s mariadb.service
7.991s webmin.service
6.095s postfix.service
4.311s httpd.service
3.926s firewalld.service
3.780s kdump.service
3.238s tuned.service
1.712s network.service
1.394s lvm2-monitor.service
1.126s systemd-logind.service
....
6. Analizar la cadena crítica al inicio
# systemd-analyze critical-chain
The time after the unit is active or started is printed after the "@" character.
The time the unit takes to start is printed after the "+" character.
multi-user.target @20.222s
└─mariadb.service @11.657s +8.565s
└─network.target @11.168s
└─network.service @9.456s +1.712s
└─NetworkManager.service @8.858s +596ms
└─firewalld.service @4.931s +3.926s
└─basic.target @4.916s
└─sockets.target @4.916s
└─dbus.socket @4.916s
└─sysinit.target @4.905s
└─systemd-update-utmp.service @4.864s +39ms
└─auditd.service @4.563s +301ms
└─systemd-tmpfiles-setup.service @4.485s +69ms
└─rhel-import-state.service @4.342s +142ms
└─local-fs.target @4.324s
└─boot.mount @4.286s +31ms
└─systemd-fsck@dev-disk-by\x2duuid-79f594ad\x2da332\x2d4730\x2dbb5f\x2d85d19608096
└─dev-disk-by\x2duuid-79f594ad\x2da332\x2d4730\x2dbb5f\x2d85d196080964.device @4
Importante: Systemctl acepta servicios (.service), puntos de montaje (.mount), sockets (.socket) y dispositivos (.device) como unidades.
7. Enumere todas las unidades disponibles
# systemctl list-unit-files
UNIT FILE STATE
proc-sys-fs-binfmt_misc.automount static
dev-hugepages.mount static
dev-mqueue.mount static
proc-sys-fs-binfmt_misc.mount static
sys-fs-fuse-connections.mount static
sys-kernel-config.mount static
sys-kernel-debug.mount static
tmp.mount disabled
brandbot.path disabled
.....
8. Enumere todas las unidades en ejecución
# systemctl list-units
UNIT LOAD ACTIVE SUB DESCRIPTION
proc-sys-fs-binfmt_misc.automount loaded active waiting Arbitrary Executable File Formats File Syste
sys-devices-pc...0-1:0:0:0-block-sr0.device loaded active plugged VBOX_CD-ROM
sys-devices-pc...:00:03.0-net-enp0s3.device loaded active plugged PRO/1000 MT Desktop Adapter
sys-devices-pc...00:05.0-sound-card0.device loaded active plugged 82801AA AC'97 Audio Controller
sys-devices-pc...:0:0-block-sda-sda1.device loaded active plugged VBOX_HARDDISK
sys-devices-pc...:0:0-block-sda-sda2.device loaded active plugged LVM PV Qzyo3l-qYaL-uRUa-Cjuk-pljo-qKtX-VgBQ8
sys-devices-pc...0-2:0:0:0-block-sda.device loaded active plugged VBOX_HARDDISK
sys-devices-pl...erial8250-tty-ttyS0.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS0
sys-devices-pl...erial8250-tty-ttyS1.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS1
sys-devices-pl...erial8250-tty-ttyS2.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS2
sys-devices-pl...erial8250-tty-ttyS3.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS3
sys-devices-virtual-block-dm\x2d0.device loaded active plugged /sys/devices/virtual/block/dm-0
sys-devices-virtual-block-dm\x2d1.device loaded active plugged /sys/devices/virtual/block/dm-1
sys-module-configfs.device loaded active plugged /sys/module/configfs
...
9. Enumere todas las unidades fallidas
# systemctl --failed
UNIT LOAD ACTIVE SUB DESCRIPTION
kdump.service loaded failed failed Crash recovery kernel arming
LOAD = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB = The low-level unit activation state, values depend on unit type.
1 loaded units listed. Pass --all to see loaded but inactive units, too.
To show all installed unit files use 'systemctl list-unit-files'.
10. Verifique si una unidad (como cron.service) está habilitada
# systemctl is-enabled crond.service
enabled
11. Comprobar si una unidad o servicio está funcionando
# systemctl status firewalld.service
firewalld.service - firewalld - dynamic firewall daemon
Loaded: loaded (/usr/lib/systemd/system/firewalld.service; enabled)
Active: active (running) since Tue 2015-04-28 16:27:55 IST; 34min ago
Main PID: 549 (firewalld)
CGroup: /system.slice/firewalld.service
└─549 /usr/bin/python -Es /usr/sbin/firewalld --nofork --nopid
Apr 28 16:27:51 tecmint systemd[1]: Starting firewalld - dynamic firewall daemon...
Apr 28 16:27:55 tecmint systemd[1]: Started firewalld - dynamic firewall daemon.
Controla y gestiona servicios con Systemctl
12. Listar todos los servicios (tanto habilitados como deshabilitados)
# systemctl list-unit-files --type=service
UNIT FILE STATE
arp-ethers.service disabled
auditd.service enabled
[email protected] disabled
blk-availability.service disabled
brandbot.service static
collectd.service disabled
console-getty.service disabled
console-shell.service disabled
cpupower.service disabled
crond.service enabled
dbus-org.fedoraproject.FirewallD1.service enabled
....
13. Cómo iniciar, reiniciar, detener, recargar servicios y verificar el estado de los servicios (como httpd.service) en Linux
# systemctl start httpd.service
# systemctl restart httpd.service
# systemctl stop httpd.service
# systemctl reload httpd.service
# systemctl status httpd.service
httpd.service - The Apache HTTP Server
Loaded: loaded (/usr/lib/systemd/system/httpd.service; enabled)
Active: active (running) since Tue 2015-04-28 17:21:30 IST; 6s ago
Process: 2876 ExecStop=/bin/kill -WINCH ${MAINPID} (code=exited, status=0/SUCCESS)
Main PID: 2881 (httpd)
Status: "Processing requests..."
CGroup: /system.slice/httpd.service
├─2881 /usr/sbin/httpd -DFOREGROUND
├─2884 /usr/sbin/httpd -DFOREGROUND
├─2885 /usr/sbin/httpd -DFOREGROUND
├─2886 /usr/sbin/httpd -DFOREGROUND
├─2887 /usr/sbin/httpd -DFOREGROUND
└─2888 /usr/sbin/httpd -DFOREGROUND
Apr 28 17:21:30 tecmint systemd[1]: Starting The Apache HTTP Server...
Apr 28 17:21:30 tecmint httpd[2881]: AH00558: httpd: Could not reliably determine the server's fully q...ssage
Apr 28 17:21:30 tecmint systemd[1]: Started The Apache HTTP Server.
Hint: Some lines were ellipsized, use -l to show in full.
Nota: Cuando usamos los comandos de inicio, reinicio, detención y recarga de systemctl, no obtendremos ningún resultado del terminal, solo el comando de estado puede imprimir el resultado.
14. Cómo activar un servicio y habilitar o deshabilitar un servicio en el momento del arranque (es decir, iniciar un servicio automáticamente cuando se inicia el sistema)
# systemctl is-active httpd.service
# systemctl enable httpd.service
# systemctl disable httpd.service
15. Cómo blindar (hacer que sea imposible iniciar) o mostrar servicios (como httpd.service)
# systemctl mask httpd.service
ln -s '/dev/null' '/etc/systemd/system/httpd.service'
# systemctl unmask httpd.service
rm '/etc/systemd/system/httpd.service'
16. Mata el servicio usando el comando systemctl
# systemctl kill httpd
# systemctl status httpd
httpd.service - The Apache HTTP Server
Loaded: loaded (/usr/lib/systemd/system/httpd.service; enabled)
Active: failed (Result: exit-code) since Tue 2015-04-28 18:01:42 IST; 28min ago
Main PID: 2881 (code=exited, status=0/SUCCESS)
Status: "Total requests: 0; Current requests/sec: 0; Current traffic: 0 B/sec"
Apr 28 17:37:29 tecmint systemd[1]: httpd.service: Got notification message from PID 2881, but recepti...bled.
Apr 28 17:37:29 tecmint systemd[1]: httpd.service: Got notification message from PID 2881, but recepti...bled.
Apr 28 17:37:39 tecmint systemd[1]: httpd.service: Got notification message from PID 2881, but recepti...bled.
Apr 28 17:37:39 tecmint systemd[1]: httpd.service: Got notification message from PID 2881, but recepti...bled.
Apr 28 17:37:49 tecmint systemd[1]: httpd.service: Got notification message from PID 2881, but recepti...bled.
Apr 28 17:37:49 tecmint systemd[1]: httpd.service: Got notification message from PID 2881, but recepti...bled.
Apr 28 17:37:59 tecmint systemd[1]: httpd.service: Got notification message from PID 2881, but recepti...bled.
Apr 28 17:37:59 tecmint systemd[1]: httpd.service: Got notification message from PID 2881, but recepti...bled.
Apr 28 18:01:42 tecmint systemd[1]: httpd.service: control process exited, code=exited status=226
Apr 28 18:01:42 tecmint systemd[1]: Unit httpd.service entered failed state.
Hint: Some lines were ellipsized, use -l to show in full.
```shell
使用Systemctl控制并管理挂载点
## 17. 列出所有系统挂载点
```shell
# systemctl list-unit-files --type=mount
UNIT FILE STATE
dev-hugepages.mount static
dev-mqueue.mount static
proc-sys-fs-binfmt_misc.mount static
sys-fs-fuse-connections.mount static
sys-kernel-config.mount static
sys-kernel-debug.mount static
tmp.mount disabled
18. Montar, desmontar, volver a montar, recargar el punto de montaje del sistema y comprobar el estado del punto de montaje en el sistema
# systemctl start tmp.mount
# systemctl stop tmp.mount
# systemctl restart tmp.mount
# systemctl reload tmp.mount
# systemctl status tmp.mount
tmp.mount - Temporary Directory
Loaded: loaded (/usr/lib/systemd/system/tmp.mount; disabled)
Active: active (mounted) since Tue 2015-04-28 17:46:06 IST; 2min 48s ago
Where: /tmp
What: tmpfs
Docs: man:hier(7)
http://www.freedesktop.org/wiki/Software/systemd/APIFileSystems
Process: 3908 ExecMount=/bin/mount tmpfs /tmp -t tmpfs -o mode=1777,strictatime (code=exited, status=0/SUCCESS)
Apr 28 17:46:06 tecmint systemd[1]: Mounting Temporary Directory...
Apr 28 17:46:06 tecmint systemd[1]: tmp.mount: Directory /tmp to mount over is not empty, mounting anyway.
Apr 28 17:46:06 tecmint systemd[1]: Mounted Temporary Directory.
19. Activar, habilitar o deshabilitar puntos de montaje en el momento del arranque (montar automáticamente en el arranque del sistema)
# systemctl is-active tmp.mount
# systemctl enable tmp.mount
# systemctl disable tmp.mount
20. Máscara (para que no se pueda habilitar) o punto de montaje visible en Linux
# systemctl mask tmp.mount
ln -s '/dev/null' '/etc/systemd/system/tmp.mount'
# systemctl unmask tmp.mount
rm '/etc/systemd/system/tmp.mount'
Use Systemctl para controlar y administrar sockets
21. Enumere todos los enchufes del sistema disponibles
# systemctl list-unit-files --type=socket
UNIT FILE STATE
dbus.socket static
dm-event.socket enabled
lvm2-lvmetad.socket enabled
rsyncd.socket disabled
sshd.socket disabled
syslog.socket static
systemd-initctl.socket static
systemd-journald.socket static
systemd-shutdownd.socket static
systemd-udevd-control.socket static
systemd-udevd-kernel.socket static
11 unit files listed.
22. Iniciar, reiniciar, detener, recargar socket y comprobar su estado en Linux
# systemctl start cups.socket
# systemctl restart cups.socket
# systemctl stop cups.socket
# systemctl reload cups.socket
# systemctl status cups.socket
cups.socket - CUPS Printing Service Sockets
Loaded: loaded (/usr/lib/systemd/system/cups.socket; enabled)
Active: active (listening) since Tue 2015-04-28 18:10:59 IST; 8s ago
Listen: /var/run/cups/cups.sock (Stream)
Apr 28 18:10:59 tecmint systemd[1]: Starting CUPS Printing Service Sockets.
Apr 28 18:10:59 tecmint systemd[1]: Listening on CUPS Printing Service Sockets.
23. Active el zócalo al inicio y actívelo o desactívelo (inicio automático al inicio del sistema)
# systemctl is-active cups.socket
# systemctl enable cups.socket
# systemctl disable cups.socket
24. Bloquear (hacer que sea imposible comenzar) o mostrar el zócalo
# systemctl mask cups.socket
ln -s '/dev/null' '/etc/systemd/system/cups.socket'
# systemctl unmask cups.socket
rm '/etc/systemd/system/cups.socket'
服务的CPU利用率(分配额)
25. Obtenga la asignación de CPU actual de un servicio (como httpd)
# systemctl show -p CPUShares httpd.service
CPUShares=1024
Nota: El porcentaje de asignación de CPU predeterminado de cada servicio = 1024, puede aumentar/disminuir el porcentaje de asignación de CPU de un proceso.
26. Limite la cuota de asignación de CPU de un servicio (httpd.service) a 2000 CPUShares/
# systemctl set-property httpd.service CPUShares=2000
# systemctl show -p CPUShares httpd.service
CPUShares=2000
Nota: Cuando configura CPUShares para un servicio, se creará automáticamente un directorio con el nombre del servicio (como httpd.service), que contiene un archivo llamado 90-CPUShares.conf, que contiene información sobre el límite de CPUShare. Este archivo puede ser visto con:
# vi /etc/systemd/system/httpd.service.d/90-CPUShares.conf
[Service]
CPUShares=2000
27. Verifica todos los detalles de configuración de un servicio
# systemctl show httpd
Id=httpd.service
Names=httpd.service
Requires=basic.target
Wants=system.slice
WantedBy=multi-user.target
Conflicts=shutdown.target
Before=shutdown.target multi-user.target
After=network.target remote-fs.target nss-lookup.target systemd-journald.socket basic.target system.slice
Description=The Apache HTTP Server
LoadState=loaded
ActiveState=active
SubState=running
FragmentPath=/usr/lib/systemd/system/httpd.service
....
28. Analizar la cadena crítica de un servicio (httpd)
# systemd-analyze critical-chain httpd.service
The time after the unit is active or started is printed after the "@" character.
The time the unit takes to start is printed after the "+" character.
httpd.service +142ms
└─network.target @11.168s
└─network.service @9.456s +1.712s
└─NetworkManager.service @8.858s +596ms
└─firewalld.service @4.931s +3.926s
└─basic.target @4.916s
└─sockets.target @4.916s
└─dbus.socket @4.916s
└─sysinit.target @4.905s
└─systemd-update-utmp.service @4.864s +39ms
└─auditd.service @4.563s +301ms
└─systemd-tmpfiles-setup.service @4.485s +69ms
└─rhel-import-state.service @4.342s +142ms
└─local-fs.target @4.324s
└─boot.mount @4.286s +31ms
└─systemd-fsck@dev-disk-by\x2duuid-79f594ad\x2da332\x2d4730\x2dbb5f\x2d85d196080964.service @4.092s +149ms
└─dev-disk-by\x2duuid-79f594ad\x2da332\x2d4730\x2dbb5f\x2d85d196080964.device @4.092s
29. Obtenga la lista de dependencias de un servicio (httpd)
# systemctl list-dependencies httpd.service
httpd.service
├─system.slice
└─basic.target
├─firewalld.service
├─microcode.service
├─rhel-autorelabel-mark.service
├─rhel-autorelabel.service
├─rhel-configure.service
├─rhel-dmesg.service
├─rhel-loadmodules.service
├─paths.target
├─slices.target
│ ├─-.slice
│ └─system.slice
├─sockets.target
│ ├─dbus.socket
....
30. Enumere los grupos de control por rango
# systemd-cgls
├─1 /usr/lib/systemd/systemd --switched-root --system --deserialize 23
├─user.slice
│ └─user-0.slice
│ └─session-1.scope
│ ├─2498 sshd: root@pts/0
│ ├─2500 -bash
│ ├─4521 systemd-cgls
│ └─4522 systemd-cgls
└─system.slice
├─httpd.service
│ ├─4440 /usr/sbin/httpd -DFOREGROUND
│ ├─4442 /usr/sbin/httpd -DFOREGROUND
│ ├─4443 /usr/sbin/httpd -DFOREGROUND
│ ├─4444 /usr/sbin/httpd -DFOREGROUND
│ ├─4445 /usr/sbin/httpd -DFOREGROUND
│ └─4446 /usr/sbin/httpd -DFOREGROUND
├─polkit.service
│ └─721 /usr/lib/polkit-1/polkitd --no-debug
....
```shell
## 31. 按CPU、内存、输入和输出列出控制组
```shell
# systemd-cgtop
Path Tasks %CPU Memory Input/s Output/s
/ 83 1.0 437.8M - -
/system.slice - 0.1 - - -
/system.slice/mariadb.service 2 0.1 - - -
/system.slice/tuned.service 1 0.0 - - -
/system.slice/httpd.service 6 0.0 - - -
/system.slice/NetworkManager.service 1 - - - -
/system.slice/atop.service 1 - - - -
/system.slice/atopacct.service 1 - - - -
/system.slice/auditd.service 1 - - - -
/system.slice/crond.service 1 - - - -
/system.slice/dbus.service 1 - - - -
/system.slice/firewalld.service 1 - - - -
/system.slice/lvm2-lvmetad.service 1 - - - -
/system.slice/polkit.service 1 - - - -
/system.slice/postfix.service 3 - - - -
/system.slice/rsyslog.service 1 - - - -
/system.slice/system-getty.slice/[email protected] 1 - - - -
/system.slice/systemd-journald.service 1 - - - -
/system.slice/systemd-logind.service 1 - - - -
/system.slice/systemd-udevd.service 1 - - - -
/system.slice/webmin.service 1 - - - -
/user.slice/user-0.slice/session-1.scope 3 - - - -
nivel de ejecución del sistema de control
32. Iniciar el modo de rescate del sistema
# systemctl rescue
Broadcast message from root@tecmint on pts/0 (Wed 2015-04-29 11:31:18 IST):
The system is going down to rescue mode NOW!
33. Ingrese al modo de emergencia
# systemctl emergency
Welcome to emergency mode! After logging in, type "journalctl -xb" to view
system logs, "systemctl reboot" to reboot, "systemctl default" to try again
to boot into default mode.
34. Enumere el nivel de ejecución utilizado actualmente
# systemctl get-default
multi-user.target
35. Inicie el nivel de ejecución 5, es decir, el modo de gráficos
# systemctl isolate runlevel5.target
o
# systemctl isolate graphical.target
36. Inicie el nivel de ejecución 3, es decir, modo multiusuario (línea de comando)
# systemctl isolate runlevel3.target
o
# systemctl isolate multiuser.target
36. Configure el modo multiusuario o el modo gráfico como el nivel de ejecución predeterminado
# systemctl set-default runlevel3.target
# systemctl set-default runlevel5.target
37. Reiniciar, detener, suspender, hibernar o poner el sistema en suspensión híbrida
# systemctl reboot
# systemctl halt
# systemctl suspend
# systemctl hibernate
# systemctl hybrid-sleep
Para aquellos que no saben qué son los niveles de ejecución, aquí están las instrucciones.
Nivel de ejecución 0: Apagar el sistema
Nivel de ejecución 1: ¿Rescate? Modo de mantenimiento
Nivel de ejecución 3: multiusuario, sin sistema gráfico
Nivel de ejecución 4: multiusuario, sin sistema gráfico
Nivel de ejecución 5: multiusuario, sistema gráfico
Nivel de ejecución 6: apagar y reiniciar la máquina
Eso es todo. Mantente conectado y comenta. No olvides darnos tu valiosa opinión en los comentarios a continuación. Dale me gusta, comparte con nosotros y difunde.
Original: https://linux.cn/article-5926-1.html