Detailed configuration steps for connecting Hikvision Dahua surveillance cameras to the SkeyeVSS video fusion platform

Surveillance camera access to SkeyeVSS video fusion platform configuration

• Monitoring access preparation

1. a laptop
2. Install Hikvision camera debugging tool
3. Install Dahua camera debugging tool
4. Hardware debugging tools (bring your own)

• Monitoring access steps

1. Hikvision network camera access steps:

1. Open the device network search tool (SADPTool.exe) and open the interface as shown below:
2. Under normal circumstances, you can search when the network cable is connected. If you click the "Refresh" button and still can't find it, you can restart the search tool and you should be able to search, as shown below:

1. Double-click the searched device item to access the camera background. Sometimes if there is no response after double-clicking, just click the refresh button a few times, or open the browser and enter the camera IP address, such as: http: // 192.168.1.100  is enough;
2. If access is not possible, the computer needs to configure an IP address in the same network segment, open the network and Internet settings, as shown in the figure below, and the configured IP address must be consistent with the first three items of the searched camera IP address. As shown below:

Manually configured IP addresses only require configuring the IP address and subnet mask.

1. Log in to the network camera background. Default username: admin and password: skeyevss. Enter to log in to the camera background. If the password is incorrect, please obtain the correct password and enter it again, as shown in the following figure:

1. After logging in to the backend, open "Configuration"->"Network"->Advanced Configuration->Select the platform access method. If there is EHome, select the Ehome protocol (2.0 or 5.0). If not, select the 28181 protocol access, as shown in the figure below. Show:

1. National standard access configuration

First, check Start, then select the protocol, and then configure the server SIP IP and port in sequence. Password: 12345678. The SIP user name and SIP user authentication ID can be configured to be the same. The details can be set according to the national standard encoding ID of the point document. ,As shown below:

After the registration is completed, refresh the page. If the registration status shows "online", it means the national standard access is successful.

1. Ehome protocol access configuration

First, select the Ehome (ISUP) protocol, then check to enable it, and configure the server IP address: 114.116.122.72. If it is the Ehome2.0 protocol, you do not need to configure a password. If it is the 5.0 protocol, you need to configure the password: abc1234

Just click Save.

After successful registration, the registration status shows "Online" to indicate successful registration.

1. Dahua network camera access steps'

(1) First, open the Dahua network camera search tool (ConfigTool) and open the interface as shown:

If the device cannot be found, you need to access the router and configure the network routing IP . The machine can be manually set to 1 92.168.1.x network segment IP, or use DHCP to automatically search. If it is still not found, you can restart it. config tool configuration tool, or re-plug the network cable, you should be able to search for it.

(2) Click "WEB" to enter the camera backend, or access the web backend through http://192.168.1.100 using the IP address (192.168.1.100) , as shown in the figure below:

Enter username: admin Password: skeyevss

   (3) Configure national standard access through Settings->Network Settings->Platform Access->National Standard 28181, as shown in the figure below:

First, check the enable access

Then, configure

SIP server IP: 114.116.122.72

Port: 15060

Equipment ID reference point national standard ID configuration document

Registration password: 12345678

After the configuration is completed, click OK. Under normal circumstances, the red refresh button next to the access enable turns green, indicating that the access is completed.

3. Monitoring access and debugging

You can enter the video fusion platform background through http://114.116.122.72:8000  (default username: skeyevss password: skeyevss) to view the accessed surveillance video.