| gNeighborLookupThreshold |
1 The condition that triggers roam scan is in the WCNSS_qcom_cfg.ini file gNeighborLookupThreshold=78, which means that roam scan will be triggered when the signal is less than -78db. |
0 |
120 |
0 |
| RTSThreshold |
Mainly used to solve the "hidden node" problem, refer to https://blog.csdn.net/oriel123/article/details/77976737 |
|
|
|
| WmmIsEnabled |
WMM is enabled: 1-enable, only QoS, 2-enable, but not enable QoS, 0-automatic, join any AP |
0 |
2 |
0 |
| BandCapability |
Preferred frequency band, 0: both, 1: 2.4G only, 2: 5G only |
0 |
2 |
1 |
| gTxBFEnable |
Enable Tx beamforming |
0 |
1 |
0 |
| Intf0MacAddress |
Assigned MAC address-the location has been used until the NV item is inserted. There are 4, f0-f3 |
|
|
|
| gNumRxAnt |
Set 1 x 1 as the default antenna configuration. |
1 |
2 |
2 |
| gNthBeaconFilter |
Beacon filtering frequency (in units of beacon interval). Every Nth beacon will check the content of the change beacon frame. If the beacon frame changes, the frame is forwarded to the host. |
0 |
255 |
10 |
| McastBcastFilter |
Flag value for filtering multicast and broadcast Rx packets: 0-no filtering, 1-filtering all multicasts, 2-filtering all broadcasts, 3-filtering all multicasts and broadcasts |
0 |
3 |
0 |
| hostArpOffload |
Enable/disable the HostARPOffload function to uninstall the ARP reply firmware. For more information |
|
|
|
| gEnableApProt |
802.11n protection flag |
|
|
|
| gFixedRate |
Fixed transmission data rate; 0 means automatic rate adjustment. |
|
|
0 |
| gDisableIntraBssFwd |
BSS internal forwarding |
|
|
0 |
| g11dSupportEnabled |
Enable/disable 11d support |
0 |
1 |
1 |
| gNeighborScanTimerPeriod |
Single channel in CCX support and fast transition scan |
3 |
300 |
200 |
| gShortGI20Mhz gShortGI40Mhz |
Enable short guard interval for HT20 and HT40 |
|
|
|
| gAPAutoShutOff |
If there is no activity for this period, then SAP disconnects with that STA. Enable/disable values are in seconds Automatic shutdown value, in seconds. A value of 0 means automatic shutdown is disabled |
|
|
|
| gChannelBondingMode5GHz gChannelBondingMode24GHz |
After setting to 1, 2.4G/5G can open the maximum channel bandwidth in frequency bands, such as 40M, 80M, 160M |
|
|
|
| gEnableModulatedDTIM |
Enable/disable modulation DTIM function |
0 |
5 |
0 |
| gMaxLIModulatedDTIM |
Modulate the maximum LI of DTIM |
1 |
10 |
10 |
| gGoKeepAlivePeriod |
gGoKeepAlivePeriod / gApKeepAlivePeriod is the time used to check whether the frame is being sent. Therefore, the total effective detection time is gGoLinkMonitorPeriod +gGoKeepAlivePeriod / gApLinkMonitorPeriod +gApKeepAlivePeriod |
3 |
255 |
3 |
| gEnableAutomaticTxPowerControl |
Enable automatic Tx power control |
|
|
|
| gEnableCloseLoop |
0 for OLPC 1 for CLPC and SCPC |
|
|
|
| gDataInactivityTimeout |
Data inactivity timeout milliseconds during power saving) |
1 |
255 |
20 |
| gVhtChannelWidth |
Channel width of VHT mode. 1-20 and 40MHz, 2-80MHz |
|
|
|
| g_enable_probereq_whitelist_ies |
Enable or disable the whitelist of Probe Req information elements |
|
|
|