1. WiFi settings
1. WiFI network configuration steps are as follows:
- Connect your phone non 5Ghz WiFi, two-dimensional code scanning box (Figure 1), lost a good WiFi password, do not point connection (Figure 2)!
- Operation box. Press the green button behind the door, enter the administrator password: 123456 Press # to confirm, press 6 to configure the network, the box indicator flashes (Figure 3). Immediately operate the phone and click Connect (Figure 4).
- After the network distribution is successful, the mobile phone page jumps (Figure 5). Click on the device that appears-Smart Safe xxx (Figure 6).
- Click Bind Device (Figure 7). Device binding is successful, click on the safe to view (Figure 8).
- View the safe page (Figure 9).
2. WiFI distribution network timeout problem
- You must use 2.4Ghz WiFi, dual-band routers need to turn off 5Ghz WiFi or set to two WiFi. Changing the settings has no effect on the network!
- The signal distance of the box is limited, please put the box and the router in a room to match the network, do not partition the wall!
- Observe the distribution light of the box during the distribution, flashing!
Modify the setting steps of the dual-band router:
1) Connect the mobile phone to wifi, enter the management address on the back of the router in the browser
2) Log in to your own router, and forget the password to reset the router
3) Turn off multi-band integration or 5G preference in the wireless settings Set two WiFi passwords, save and exit.
4) Use 2.4Ghz wifi distribution network
. 3. WiFi function introduction
After the operation of binding the safe, if there is a change in the unpacking status of the box, it will be notified in a timely manner via WeChat. After receiving the notification, please confirm the unpacking status information of the safe to prevent property damage caused by unexpected circumstances. There are four types of messages that can be notified:
- The door is opened with the correct fingerprint or password
- The battery is under voltage, please replace the battery in time
- Strong vibration, please confirm the situation
- The wrong fingerprint or password has been used to try to open the box multiple times, please confirm the situation
4. WiFi remote door opening
Press long on the panel # will be in the state of applying for remote door opening (the indicator flashes), you will receive a remote door opening request on the mobile phone, click on the message to enter the door opening interface, agree within 30 seconds to open the door, refuse to accept or not operate the door is still Disabled. After consent, the door can be opened and you will receive a remote door opening message. As shown below.
5. Temporary password
After setting the door opening password, the box can be used without binding the device. In the menu bar of the Bull Lock-the temporary password will jump to the temporary password interface, enter the box's door opening password (the function cannot be used if the door opening password is not set, the function cannot be used if the box is not supported), click to generate a temporary password, you can use The generated temporary password is unpacked on the safe. As shown below.
2. Other function settings of fingerprint
1. Password setting
1.1 User password
Press the green button behind the door and enter the initial management password: "123456" according to the system prompt. Press the "#" key, then press the "1" key, enter the 4-12 digit new password, press the "#" key, please enter the new password, and finally press the "#" key to confirm, indicating that the setting is successful, press the "*" key drop out.
1.2 Management password
Press the green button behind the door and enter the initial management password: "123456" according to the system prompt. Press the "#" key, then press the "4" key, enter the 4-12 digit new password, press the "#" key, please re-enter the new password, and finally press the "#" key to confirm that the setting is successful, press the "*" key drop out.
2. Fingerprint settings
2.1 Add fingerprint
Press the green button behind the door and enter the initial management password: "123456" according to the system prompt. If the management password has been modified, please enter the modified management password, press the "#" key, then press the "2" key, the fingerprint window lights up, please put your finger on the voice prompt, let your finger rest in the fingerprint window for 1 second, the voice Prompt, please lift your finger, lift up and put on three times in succession, the unlock light is on, the system prompts that the registration is successful. If you need to add other fingerprints, please press the "2" key. After the registration is successful, press the "*" key to exit. Registration fails, the lock light turns on, and the system will emit a beep.
2.2 Delete fingerprint
Press the green button behind the door and enter the initial management password: "123456" according to the system prompt. If the management password has been modified, please enter the modified management password, press the "#" key, then press the "3" key, the fingerprint window lights up, please leave the fingerprint to be deleted in the fingerprint window for 3 seconds, the system prompts to delete The successful unlock light is on. If you need to delete other fingerprints, please press the "3" key. After the deletion is successful, press the "*" key to exit. If the deletion fails, the system will emit a beep.
3 Set the on mode
The system defaults to the common mode, that is, the password or fingerprint is turned on.
Press the green button behind the door and enter the initial management password: "123456" according to the system prompt. If modified, please enter the modified password, press the "#" key, and then press the "5" key. Press "1" for the common mode, that is, the password or fingerprint is turned on; press "2" for the security mode, that is, the fingerprint + password is turned on, you need to enter the fingerprint first, you can turn on after entering the password, and press the "*" button to exit .
4 Open and close the cabinet door
4.1 Open the cabinet door,
slide open the main lock hole cover and insert the main lock key, and turn clockwise to the limit.
Common mode: light touch the key area, enter a new password or do not touch the key area, directly put the registered finger in the fingerprint window, the system prompts verification, and rotate the handle clockwise to the limit within 5 seconds. Open the cabinet door.
Safe mode: light touch on the key area, enter the password that has been set, the system prompts verification and the fingerprint window lights up, enter the fingerprint directly, the system prompts verification, and rotate the handle clockwise to the limit within 5 seconds Cabinet door.
4.2 Closing the cabinet door
When you need to close the cabinet door after accessing valuables, first close the cabinet door to the limit, then turn the handle counterclockwise to the limit, and then turn the main lock key counterclockwise to the limit, the door lock key After unplugging, please keep it in a safe place.
5 Other functions
5.1 Vibration alarm
light touches the bright button area, press "*" key, the system prompts the alert to open, the cabinet is subject to vibration, the built-in alarm will emit an alarm sound, and it will remain alert after 60 seconds. Enter the correct password or fingerprint when alarm Dismiss the alarm (note the open mode). You need to reset the alert every time you turn it on.
5.2 Fingerprint error alarm When the
fingerprint or password is entered six times in a row, the panel will emit a 20-second treble horn. At this time, entering the correct password or fingerprint can cancel the alarm.
5.3 Restore settings
Press the green button behind the door for 3-5 seconds, the system prompts that the factory settings are successfully restored, and restores to the factory state (initial password 123456), you can reset the password or fingerprint.
5.4 Undervoltage
When the battery is undervoltage, the system automatically prompts that the power is low, please replace the battery.
6 Emergency start
When the system fails, the emergency key can be used to open the door
A: insert the main lock key and turn it clockwise to the limit, slide the emergency lock cover, insert the emergency lock key and rotate it counterclockwise to the limit, then rotate the handle clockwise To the limit, you can open the door.
Type B: Press and rotate to remove the emergency lock cover, insert the emergency lock key and rotate counterclockwise to the limit, and then rotate the handle clockwise to the limit to open the cabinet door.
